34. IXGBE Driver

34.1. Vector PMD for IXGBE

Vector PMD uses Intel® SIMD instructions to optimize packet I/O. It improves load/store bandwidth efficiency of L1 data cache by using a wider SSE/AVX register 1 (1). The wider register gives space to hold multiple packet buffers so as to save instruction number when processing bulk of packets.

There is no change to PMD API. The RX/TX handler are the only two entries for vPMD packet I/O. They are transparently registered at runtime RX/TX execution if all condition checks pass.

Some constraints apply as pre-conditions for specific optimizations on bulk packet transfers. The following sections explain RX and TX constraints in the vPMD.

34.1.1. RX Constraints

34.1.1.1. Linux Prerequisites and Pre-conditions

The following prerequisites apply:

  • To enable vPMD to work for RX, bulk allocation for Rx must be allowed.

Ensure that the following pre-conditions are satisfied:

  • rxq->rx_free_thresh >= RTE_PMD_IXGBE_RX_MAX_BURST
  • rxq->rx_free_thresh < rxq->nb_rx_desc
  • (rxq->nb_rx_desc % rxq->rx_free_thresh) == 0
  • rxq->nb_rx_desc < (IXGBE_MAX_RING_DESC - RTE_PMD_IXGBE_RX_MAX_BURST)

These conditions are checked in the code.

Scattered packets are not supported in this mode. If an incoming packet is greater than the maximum acceptable length of one “mbuf” data size (by default, the size is 2 KB), vPMD for RX would be disabled.

By default, IXGBE_MAX_RING_DESC is set to 4096 and RTE_PMD_IXGBE_RX_MAX_BURST is set to 32.

34.1.1.2. Windows Prerequisites and Pre-conditions

  • Follow the guide for Windows to setup the basic DPDK environment.
  • Identify the Intel® Ethernet adapter and get the latest NVM/FW version.
  • To access any Intel® Ethernet hardware, load the NetUIO driver in place of existing built-in (inbox) driver.
  • To load NetUIO driver, follow the steps mentioned in dpdk-kmods repository.
  • Loading of private Dynamic Device Personalization (DDP) package is not supported on Windows.

34.1.1.3. Feature not Supported by RX Vector PMD

Some features are not supported when trying to increase the throughput in vPMD. They are:

  • IEEE1588
  • FDIR
  • RX checksum off load

Other features are supported using optional MACRO configuration. They include:

  • HW VLAN strip
  • HW extend dual VLAN

To guarantee the constraint, capabilities in dev_conf.rxmode.offloads will be checked:

  • RTE_ETH_RX_OFFLOAD_VLAN_STRIP
  • RTE_ETH_RX_OFFLOAD_VLAN_EXTEND
  • RTE_ETH_RX_OFFLOAD_CHECKSUM
  • dev_conf

34.1.1.5. VF Runtime Options

The following devargs options can be enabled at runtime. They must be passed as part of EAL arguments. For example,

dpdk-testpmd -a af:10.0,pflink_fullchk=1 -- -i

  • pflink_fullchk (default 0)

    When calling rte_eth_link_get_nowait() to get VF link status, this option is used to control how VF synchronizes its status with PF’s. If set, VF will not only check the PF’s physical link status by reading related register, but also check the mailbox status. We call this behavior as fully checking. And checking mailbox will trigger PF’s mailbox interrupt generation. If unset, the application can get the VF’s link status quickly by just reading the PF’s link status register, this will avoid the whole system’s mailbox interrupt generation.

    rte_eth_link_get() will still use the mailbox method regardless of the pflink_fullchk setting.

34.1.1.6. RX Burst Size

As vPMD is focused on high throughput, it assumes that the RX burst size is equal to or greater than 32 per burst. It returns zero if using nb_pkt < 32 as the expected packet number in the receive handler.

34.1.2. TX Constraint

34.1.2.1. Prerequisite

The only prerequisite is related to tx_rs_thresh. The tx_rs_thresh value must be greater than or equal to RTE_PMD_IXGBE_TX_MAX_BURST, but less or equal to RTE_IXGBE_TX_MAX_FREE_BUF_SZ. Consequently, by default the tx_rs_thresh value is in the range 32 to 64.

34.1.2.2. Feature not Supported by TX Vector PMD

TX vPMD only works when offloads is set to 0

This means that it does not support any TX offload.

34.2. Application Programming Interface

In DPDK release v16.11 an API for ixgbe specific functions has been added to the ixgbe PMD. The declarations for the API functions are in the header rte_pmd_ixgbe.h.

34.3. Sample Application Notes

34.3.1. l3fwd

When running l3fwd with vPMD, there is one thing to note. In the configuration, ensure that RTE_ETH_RX_OFFLOAD_CHECKSUM in port_conf.rxmode.offloads is NOT set. Otherwise, by default, RX vPMD is disabled.

34.3.2. load_balancer

As in the case of l3fwd, to enable vPMD, do NOT set RTE_ETH_RX_OFFLOAD_CHECKSUM in port_conf.rxmode.offloads. In addition, for improved performance, use -bsz “(32,32),(64,64),(32,32)” in load_balancer to avoid using the default burst size of 144.

34.4. Limitations or Known issues

34.4.1. Malicious Driver Detection not Supported

The Intel x550 series NICs support a feature called MDD (Malicious Driver Detection) which checks the behavior of the VF driver. If this feature is enabled, the VF must use the advanced context descriptor correctly and set the CC (Check Context) bit. DPDK PF doesn’t support MDD, but kernel PF does. We may hit problem in this scenario kernel PF + DPDK VF. If user enables MDD in kernel PF, DPDK VF will not work. Because kernel PF thinks the VF is malicious. But actually it’s not. The only reason is the VF doesn’t act as MDD required. There’s significant performance impact to support MDD. DPDK should check if the advanced context descriptor should be set and set it. And DPDK has to ask the info about the header length from the upper layer, because parsing the packet itself is not acceptable. So, it’s too expensive to support MDD. When using kernel PF + DPDK VF on x550, please make sure to use a kernel PF driver that disables MDD or can disable MDD.

Some kernel drivers already disable MDD by default while some kernels can use the command insmod ixgbe.ko MDD=0,0 to disable MDD. Each “0” in the command refers to a port. For example, if there are 6 ixgbe ports, the command should be changed to insmod ixgbe.ko MDD=0,0,0,0,0,0.

34.4.2. Statistics

The statistics of ixgbe hardware must be polled regularly in order for it to remain consistent. Running a DPDK application without polling the statistics will cause registers on hardware to count to the maximum value, and “stick” at that value.

In order to avoid statistic registers every reaching the maximum value, read the statistics from the hardware using rte_eth_stats_get() or rte_eth_xstats_get().

The maximum time between statistics polls that ensures consistent results can be calculated as follows:

max_read_interval = UINT_MAX / max_packets_per_second
max_read_interval = 4294967295 / 14880952
max_read_interval = 288.6218096127183 (seconds)
max_read_interval = ~4 mins 48 sec.

In order to ensure valid results, it is recommended to poll every 4 minutes.

34.4.3. MTU setting

Although the user can set the MTU separately on PF and VF ports, the ixgbe NIC only supports one global MTU per physical port. So when the user sets different MTUs on PF and VF ports in one physical port, the real MTU for all these PF and VF ports is the largest value set. This behavior is based on the kernel driver behavior.

34.4.4. VF MAC address setting

On ixgbe, the concept of “pool” can be used for different things depending on the mode. In VMDq mode, “pool” means a VMDq pool. In IOV mode, “pool” means a VF.

There is no RTE API to add a VF’s MAC address from the PF. On ixgbe, the rte_eth_dev_mac_addr_add() function can be used to add a VF’s MAC address, as a workaround.

34.4.5. X550 does not support legacy interrupt mode

34.4.5.1. Description

X550 cannot get interrupts if using uio_pci_generic module or using legacy interrupt mode of igb_uio or vfio. Because the errata of X550 states that the Interrupt Status bit is not implemented. The errata is the item #22 from X550 spec update

34.4.5.2. Implication

When using uio_pci_generic module or using legacy interrupt mode of igb_uio or vfio, the Interrupt Status bit would be checked if the interrupt is coming. Since the bit is not implemented in X550, the irq cannot be handled correctly and cannot report the event fd to DPDK apps. Then apps cannot get interrupts and dmesg will show messages like irq #No.: `` ``nobody cared.

34.4.5.3. Workaround

Do not bind the uio_pci_generic module in X550 NICs. Do not bind igb_uio with legacy mode in X550 NICs. Before binding vfio with legacy mode in X550 NICs, use modprobe vfio `` ``nointxmask=1 to load vfio module if the intx is not shared with other devices.

34.4.6. RSS isn’t supported when QinQ is enabled

Due to FW limitation, IXGBE doesn’t support RSS when QinQ is enabled currently.

34.4.7. UDP with zero checksum is reported as error

Intel 82599 10 Gigabit Ethernet Controller Specification Update (Revision 2.87) Errata: 44 Integrity Error Reported for IPv4/UDP Packets With Zero Checksum

To support UDP zero checksum, the zero and bad UDP checksum packet is marked as RTE_MBUF_F_RX_L4_CKSUM_UNKNOWN, so the application needs to recompute the checksum to validate it.

34.5. Inline crypto processing support

Inline IPsec processing is supported for RTE_SECURITY_ACTION_TYPE_INLINE_CRYPTO mode for ESP packets only:

  • ESP authentication only: AES-128-GMAC (128-bit key)
  • ESP encryption and authentication: AES-128-GCM (128-bit key)

IPsec Security Gateway Sample Application supports inline IPsec processing for ixgbe PMD.

For more details see the IPsec Security Gateway Sample Application and Security library documentation.

34.6. Virtual Function Port Representors

The IXGBE PF PMD supports the creation of VF port representors for the control and monitoring of IXGBE virtual function devices. Each port representor corresponds to a single virtual function of that device. Using the devargs option representor the user can specify which virtual functions to create port representors for on initialization of the PF PMD by passing the VF IDs of the VFs which are required.:

-a DBDF,representor=[0,1,4]

Currently hot-plugging of representor ports is not supported so all required representors must be specified on the creation of the PF.

34.7. Supported Chipsets and NICs

  • Intel 82599EB 10 Gigabit Ethernet Controller
  • Intel 82598EB 10 Gigabit Ethernet Controller
  • Intel 82599ES 10 Gigabit Ethernet Controller
  • Intel 82599EN 10 Gigabit Ethernet Controller
  • Intel Ethernet Controller X540-AT2
  • Intel Ethernet Controller X550-BT2
  • Intel Ethernet Controller X550-AT2
  • Intel Ethernet Controller X550-AT
  • Intel Ethernet Converged Network Adapter X520-SR1
  • Intel Ethernet Converged Network Adapter X520-SR2
  • Intel Ethernet Converged Network Adapter X520-LR1
  • Intel Ethernet Converged Network Adapter X520-DA1
  • Intel Ethernet Converged Network Adapter X520-DA2
  • Intel Ethernet Converged Network Adapter X520-DA4
  • Intel Ethernet Converged Network Adapter X520-QDA1
  • Intel Ethernet Converged Network Adapter X520-T2
  • Intel 10 Gigabit AF DA Dual Port Server Adapter
  • Intel 10 Gigabit AT Server Adapter
  • Intel 10 Gigabit AT2 Server Adapter
  • Intel 10 Gigabit CX4 Dual Port Server Adapter
  • Intel 10 Gigabit XF LR Server Adapter
  • Intel 10 Gigabit XF SR Dual Port Server Adapter
  • Intel 10 Gigabit XF SR Server Adapter
  • Intel Ethernet Converged Network Adapter X540-T1
  • Intel Ethernet Converged Network Adapter X540-T2
  • Intel Ethernet Converged Network Adapter X550-T1
  • Intel Ethernet Converged Network Adapter X550-T2

34.8. Testpmd driver specific commands

Some ixgbe driver specific features are integrated in testpmd.

34.8.1. set split drop enable (for VF)

Set split drop enable bit for VF from PF:

testpmd> set vf split drop (port_id) (vf_id) (on|off)

34.8.2. set macsec offload

Enable/disable MACsec offload:

testpmd> set macsec offload (port_id) on encrypt (on|off) replay-protect (on|off)
testpmd> set macsec offload (port_id) off

34.8.3. set macsec sc

Configure MACsec secure connection (SC):

testpmd> set macsec sc (tx|rx) (port_id) (mac) (pi)

Note

The pi argument is ignored for tx. Check the NIC Datasheet for hardware limitations.

34.8.4. set macsec sa

Configure MACsec secure association (SA):

testpmd> set macsec sa (tx|rx) (port_id) (idx) (an) (pn) (key)

Note

The IDX value must be 0 or 1. Check the NIC Datasheet for hardware limitations.

34.8.5. set tc tx min bandwidth

Set all TCs’ TX min relative bandwidth (%) globally for all PF and VFs:

testpmd> set tc tx min-bandwidth (port_id) (bw1, bw2, ...)

34.8.6. port config bypass

Enable/disable bypass feature:

port config bypass (port_id) (on|off)

34.8.7. set bypass mode

Set the bypass mode for the lowest port on bypass enabled NIC:

testpmd> set bypass mode (normal|bypass|isolate) (port_id)

34.8.8. set bypass event

Set the event required to initiate specified bypass mode for the lowest port on a bypass enabled:

testpmd> set bypass event (timeout|os_on|os_off|power_on|power_off) \
         mode (normal|bypass|isolate) (port_id)

Where:

  • timeout: Enable bypass after watchdog timeout.
  • os_on: Enable bypass when OS/board is powered on.
  • os_off: Enable bypass when OS/board is powered off.
  • power_on: Enable bypass when power supply is turned on.
  • power_off: Enable bypass when power supply is turned off.

34.8.9. set bypass timeout

Set the bypass watchdog timeout to n seconds where 0 = instant:

testpmd> set bypass timeout (0|1.5|2|3|4|8|16|32)

34.8.10. show bypass config

Show the bypass configuration for a bypass enabled NIC using the lowest port on the NIC:

testpmd> show bypass config (port_id)