DPDK
22.11.7-rc1
|
#include <rte_compat.h>
#include <rte_common.h>
#include <rte_errno.h>
#include <rte_mbuf_pool_ops.h>
#include <rte_mempool.h>
#include "rte_eventdev_trace_fp.h"
#include <rte_eventdev_core.h>
Go to the source code of this file.
Data Structures | |
struct | rte_event_dev_info |
struct | rte_event_dev_config |
struct | rte_event_queue_conf |
struct | rte_event_port_conf |
struct | rte_event_vector |
struct | rte_event |
struct | rte_event_dev_xstats_name |
Typedefs | |
typedef void(* | rte_eventdev_port_flush_t) (uint8_t dev_id, struct rte_event event, void *arg) |
typedef void(* | rte_eventdev_stop_flush_t) (uint8_t dev_id, struct rte_event event, void *arg) |
Enumerations | |
enum | rte_event_dev_xstats_mode |
Functions | |
uint8_t | rte_event_dev_count (void) |
int | rte_event_dev_get_dev_id (const char *name) |
int | rte_event_dev_socket_id (uint8_t dev_id) |
int | rte_event_dev_info_get (uint8_t dev_id, struct rte_event_dev_info *dev_info) |
int | rte_event_dev_attr_get (uint8_t dev_id, uint32_t attr_id, uint32_t *attr_value) |
int | rte_event_dev_configure (uint8_t dev_id, const struct rte_event_dev_config *dev_conf) |
int | rte_event_queue_default_conf_get (uint8_t dev_id, uint8_t queue_id, struct rte_event_queue_conf *queue_conf) |
int | rte_event_queue_setup (uint8_t dev_id, uint8_t queue_id, const struct rte_event_queue_conf *queue_conf) |
int | rte_event_queue_attr_get (uint8_t dev_id, uint8_t queue_id, uint32_t attr_id, uint32_t *attr_value) |
__rte_experimental int | rte_event_queue_attr_set (uint8_t dev_id, uint8_t queue_id, uint32_t attr_id, uint64_t attr_value) |
int | rte_event_port_default_conf_get (uint8_t dev_id, uint8_t port_id, struct rte_event_port_conf *port_conf) |
int | rte_event_port_setup (uint8_t dev_id, uint8_t port_id, const struct rte_event_port_conf *port_conf) |
__rte_experimental void | rte_event_port_quiesce (uint8_t dev_id, uint8_t port_id, rte_eventdev_port_flush_t release_cb, void *args) |
int | rte_event_port_attr_get (uint8_t dev_id, uint8_t port_id, uint32_t attr_id, uint32_t *attr_value) |
int | rte_event_dev_start (uint8_t dev_id) |
void | rte_event_dev_stop (uint8_t dev_id) |
int | rte_event_dev_stop_flush_callback_register (uint8_t dev_id, rte_eventdev_stop_flush_t callback, void *userdata) |
int | rte_event_dev_close (uint8_t dev_id) |
int | rte_event_eth_rx_adapter_caps_get (uint8_t dev_id, uint16_t eth_port_id, uint32_t *caps) |
int | rte_event_timer_adapter_caps_get (uint8_t dev_id, uint32_t *caps) |
int | rte_event_crypto_adapter_caps_get (uint8_t dev_id, uint8_t cdev_id, uint32_t *caps) |
int | rte_event_eth_tx_adapter_caps_get (uint8_t dev_id, uint16_t eth_port_id, uint32_t *caps) |
int | rte_event_dequeue_timeout_ticks (uint8_t dev_id, uint64_t ns, uint64_t *timeout_ticks) |
int | rte_event_port_link (uint8_t dev_id, uint8_t port_id, const uint8_t queues[], const uint8_t priorities[], uint16_t nb_links) |
int | rte_event_port_unlink (uint8_t dev_id, uint8_t port_id, uint8_t queues[], uint16_t nb_unlinks) |
int | rte_event_port_unlinks_in_progress (uint8_t dev_id, uint8_t port_id) |
int | rte_event_port_links_get (uint8_t dev_id, uint8_t port_id, uint8_t queues[], uint8_t priorities[]) |
int | rte_event_dev_service_id_get (uint8_t dev_id, uint32_t *service_id) |
int | rte_event_dev_dump (uint8_t dev_id, FILE *f) |
int | rte_event_dev_xstats_names_get (uint8_t dev_id, enum rte_event_dev_xstats_mode mode, uint8_t queue_port_id, struct rte_event_dev_xstats_name *xstats_names, uint64_t *ids, unsigned int size) |
int | rte_event_dev_xstats_get (uint8_t dev_id, enum rte_event_dev_xstats_mode mode, uint8_t queue_port_id, const uint64_t ids[], uint64_t values[], unsigned int n) |
uint64_t | rte_event_dev_xstats_by_name_get (uint8_t dev_id, const char *name, uint64_t *id) |
int | rte_event_dev_xstats_reset (uint8_t dev_id, enum rte_event_dev_xstats_mode mode, int16_t queue_port_id, const uint64_t ids[], uint32_t nb_ids) |
int | rte_event_dev_selftest (uint8_t dev_id) |
struct rte_mempool * | rte_event_vector_pool_create (const char *name, unsigned int n, unsigned int cache_size, uint16_t nb_elem, int socket_id) |
static uint16_t | rte_event_enqueue_burst (uint8_t dev_id, uint8_t port_id, const struct rte_event ev[], uint16_t nb_events) |
static uint16_t | rte_event_enqueue_new_burst (uint8_t dev_id, uint8_t port_id, const struct rte_event ev[], uint16_t nb_events) |
static uint16_t | rte_event_enqueue_forward_burst (uint8_t dev_id, uint8_t port_id, const struct rte_event ev[], uint16_t nb_events) |
static uint16_t | rte_event_dequeue_burst (uint8_t dev_id, uint8_t port_id, struct rte_event ev[], uint16_t nb_events, uint64_t timeout_ticks) |
static __rte_experimental int | rte_event_maintain (uint8_t dev_id, uint8_t port_id, int op) |
RTE Event Device API
In a polling model, lcores poll ethdev ports and associated rx queues directly to look for packet. In an event driven model, by contrast, lcores call the scheduler that selects packets for them based on programmer specified criteria. Eventdev library adds support for event driven programming model, which offer applications automatic multicore scaling, dynamic load balancing, pipelining, packet ingress order maintenance and synchronization services to simplify application packet processing.
The Event Device API is composed of two parts:
Event device components:
+-----------------+ | +-------------+ | +-------+ | | flow 0 | | |Packet | | +-------------+ | |event | | +-------------+ | | | | | flow 1 | |port_link(port0, queue0) +-------+ | +-------------+ | | +--------+ +-------+ | +-------------+ o-----v-----o |dequeue +------+ |Crypto | | | flow n | | | event +------->|Core 0| |work | | +-------------+ o----+ | port 0 | | | |done ev| | event queue 0 | | +--------+ +------+ +-------+ +-----------------+ | +-------+ | |Timer | +-----------------+ | +--------+ |expiry | | +-------------+ | +------o |dequeue +------+ |event | | | flow 0 | o-----------o event +------->|Core 1| +-------+ | +-------------+ | +----o port 1 | | | Event enqueue | +-------------+ | | +--------+ +------+ o-------------> | | flow 1 | | | enqueue( | +-------------+ | | queue_id, | | | +--------+ +------+ flow_id, | +-------------+ | | | |dequeue |Core 2| sched_type, | | flow n | o-----------o event +------->| | event_type, | +-------------+ | | | port 2 | +------+ subev_type, | event queue 1 | | +--------+ event) +-----------------+ | +--------+ | | |dequeue +------+ +-------+ +-----------------+ | | event +------->|Core n| |Core | | +-------------+ o-----------o port n | | | |(SW) | | | flow 0 | | | +--------+ +--+---+ |event | | +-------------+ | | | +-------+ | +-------------+ | | | ^ | | flow 1 | | | | | | +-------------+ o------+ | | | +-------------+ | | | | | flow n | | | | | +-------------+ | | | | event queue n | | | +-----------------+ | | | +-----------------------------------------------------------+
Event device: A hardware or software-based event scheduler.
Event: A unit of scheduling that encapsulates a packet or other datatype like SW generated event from the CPU, Crypto work completion notification, Timer expiry event notification etc as well as metadata. The metadata includes flow ID, scheduling type, event priority, event_type, sub_event_type etc.
Event queue: A queue containing events that are scheduled by the event dev. An event queue contains events of different flows associated with scheduling types, such as atomic, ordered, or parallel.
Event port: An application's interface into the event dev for enqueue and dequeue operations. Each event port can be linked with one or more event queues for dequeue operations.
By default, all the functions of the Event Device API exported by a PMD are lock-free functions which assume to not be invoked in parallel on different logical cores to work on the same target object. For instance, the dequeue function of a PMD cannot be invoked in parallel on two logical cores to operates on same event port. Of course, this function can be invoked in parallel by different logical cores on different ports. It is the responsibility of the upper level application to enforce this rule.
In all functions of the Event API, the Event device is designated by an integer >= 0 named the device identifier dev_id
At the Event driver level, Event devices are represented by a generic data structure of type rte_event_dev.
Event devices are dynamically registered during the PCI/SoC device probing phase performed at EAL initialization time. When an Event device is being probed, a rte_event_dev structure and a new device identifier are allocated for that device. Then, the event_dev_init() function supplied by the Event driver matching the probed device is invoked to properly initialize the device.
The role of the device init function consists of resetting the hardware or software event driver implementations.
If the device init operation is successful, the correspondence between the device identifier assigned to the new device and its associated rte_event_dev structure is effectively registered. Otherwise, both the rte_event_dev structure and the device identifier are freed.
The functions exported by the application Event API to setup a device designated by its device identifier must be invoked in the following order:
Then, the application can invoke, in any order, the functions exported by the Event API to schedule events, dequeue events, enqueue events, change event queue(s) to event port [un]link establishment and so on.
Application may use rte_event_[queue/port]_default_conf_get() to get the default configuration to set up an event queue or event port by overriding few default values.
If the application wants to change the configuration (i.e. call rte_event_dev_configure(), rte_event_queue_setup(), or rte_event_port_setup()), it must call rte_event_dev_stop() first to stop the device and then do the reconfiguration before calling rte_event_dev_start() again. The schedule, enqueue and dequeue functions should not be invoked when the device is stopped.
Finally, an application can close an Event device by invoking the rte_event_dev_close() function.
Each function of the application Event API invokes a specific function of the PMD that controls the target device designated by its device identifier.
For this purpose, all device-specific functions of an Event driver are supplied through a set of pointers contained in a generic structure of type event_dev_ops. The address of the event_dev_ops structure is stored in the rte_event_dev structure by the device init function of the Event driver, which is invoked during the PCI/SoC device probing phase, as explained earlier.
In other words, each function of the Event API simply retrieves the rte_event_dev structure associated with the device identifier and performs an indirect invocation of the corresponding driver function supplied in the event_dev_ops structure of the rte_event_dev structure.
For performance reasons, the address of the fast-path functions of the Event driver is not contained in the event_dev_ops structure. Instead, they are directly stored at the beginning of the rte_event_dev structure to avoid an extra indirect memory access during their invocation.
RTE event device drivers do not use interrupts for enqueue or dequeue operation. Instead, Event drivers export Poll-Mode enqueue and dequeue functions to applications.
The events are injected to event device through enqueue operation by event producers in the system. The typical event producers are ethdev subsystem for generating packet events, CPU(SW) for generating events based on different stages of application processing, cryptodev for generating crypto work completion notification etc
The dequeue operation gets one or more events from the event ports. The application process the events and send to downstream event queue through rte_event_enqueue_burst() if it is an intermediate stage of event processing, on the final stage, the application may use Tx adapter API for maintaining the ingress order and then send the packet/event on the wire.
The point at which events are scheduled to ports depends on the device. For hardware devices, scheduling occurs asynchronously without any software intervention. Software schedulers can either be distributed (each worker thread schedules events to its own port) or centralized (a dedicated thread schedules to all ports). Distributed software schedulers perform the scheduling in rte_event_dequeue_burst(), whereas centralized scheduler logic need a dedicated service core for scheduling. The RTE_EVENT_DEV_CAP_DISTRIBUTED_SCHED capability flag is not set indicates the device is centralized and thus needs a dedicated scheduling thread that repeatedly calls software specific scheduling function.
An event driven worker thread has following typical workflow on fastpath:
Definition in file rte_eventdev.h.
#define RTE_EVENT_DEV_CAP_QUEUE_QOS (1ULL << 0) |
Event scheduling prioritization is based on the priority and weight associated with each event queue. Events from a queue with highest priority is scheduled first. If the queues are of same priority, weight of the queues are considered to select a queue in a weighted round robin fashion. Subsequent dequeue calls from an event port could see events from the same event queue, if the queue is configured with an affinity count. Affinity count is the number of subsequent dequeue calls, in which an event port should use the same event queue if the queue is non-empty
Definition at line 225 of file rte_eventdev.h.
#define RTE_EVENT_DEV_CAP_EVENT_QOS (1ULL << 1) |
Event scheduling prioritization is based on the priority associated with each event. Priority of each event is supplied in rte_event structure on each enqueue operation.
Definition at line 237 of file rte_eventdev.h.
#define RTE_EVENT_DEV_CAP_DISTRIBUTED_SCHED (1ULL << 2) |
Event device operates in distributed scheduling mode. In distributed scheduling mode, event scheduling happens in HW or rte_event_dequeue_burst() or the combination of these two. If the flag is not set then eventdev is centralized and thus needs a dedicated service core that acts as a scheduling thread .
Definition at line 244 of file rte_eventdev.h.
#define RTE_EVENT_DEV_CAP_QUEUE_ALL_TYPES (1ULL << 3) |
Event device is capable of enqueuing events of any type to any queue. If this capability is not set, the queue only supports events of the RTE_SCHED_TYPE_ type that it was created with.
Definition at line 253 of file rte_eventdev.h.
#define RTE_EVENT_DEV_CAP_BURST_MODE (1ULL << 4) |
Event device is capable of operating in burst mode for enqueue(forward, release) and dequeue operation. If this capability is not set, application still uses the rte_event_dequeue_burst() and rte_event_enqueue_burst() but PMD accepts only one event at a time.
Definition at line 260 of file rte_eventdev.h.
#define RTE_EVENT_DEV_CAP_IMPLICIT_RELEASE_DISABLE (1ULL << 5) |
Event device ports support disabling the implicit release feature, in which the port will release all unreleased events in its dequeue operation. If this capability is set and the port is configured with implicit release disabled, the application is responsible for explicitly releasing events using either the RTE_EVENT_OP_FORWARD or the RTE_EVENT_OP_RELEASE event enqueue operations.
Definition at line 268 of file rte_eventdev.h.
#define RTE_EVENT_DEV_CAP_NONSEQ_MODE (1ULL << 6) |
Event device is capable of operating in none sequential mode. The path of the event is not necessary to be sequential. Application can change the path of event at runtime. If the flag is not set, then event each event will follow a path from queue 0 to queue 1 to queue 2 etc. If the flag is set, events may be sent to queues in any order. If the flag is not set, the eventdev will return an error when the application enqueues an event for a qid which is not the next in the sequence.
Definition at line 279 of file rte_eventdev.h.
#define RTE_EVENT_DEV_CAP_RUNTIME_PORT_LINK (1ULL << 7) |
Event device is capable of configuring the queue/port link at runtime. If the flag is not set, the eventdev queue/port link is only can be configured during initialization.
Definition at line 289 of file rte_eventdev.h.
#define RTE_EVENT_DEV_CAP_MULTIPLE_QUEUE_PORT (1ULL << 8) |
Event device is capable of setting up the link between multiple queue with single port. If the flag is not set, the eventdev can only map a single queue to each port or map a single queue to many port.
Definition at line 295 of file rte_eventdev.h.
#define RTE_EVENT_DEV_CAP_CARRY_FLOW_ID (1ULL << 9) |
Event device preserves the flow ID from the enqueued event to the dequeued event if the flag is set. Otherwise, the content of this field is implementation dependent.
Definition at line 301 of file rte_eventdev.h.
#define RTE_EVENT_DEV_CAP_MAINTENANCE_FREE (1ULL << 10) |
Event device does not require calls to rte_event_maintain(). An event device that does not set this flag requires calls to rte_event_maintain() during periods when neither rte_event_dequeue_burst() nor rte_event_enqueue_burst() are called on a port. This will allow the event device to perform internal processing, such as flushing buffered events, return credits to a global pool, or process signaling related to load balancing.
Definition at line 307 of file rte_eventdev.h.
#define RTE_EVENT_DEV_CAP_RUNTIME_QUEUE_ATTR (1ULL << 11) |
Event device is capable of changing the queue attributes at runtime i.e after rte_event_queue_setup() or rte_event_start() call sequence. If this flag is not set, eventdev queue attributes can only be configured during rte_event_queue_setup().
Definition at line 317 of file rte_eventdev.h.
#define RTE_EVENT_DEV_PRIORITY_HIGHEST 0 |
Highest priority expressed across eventdev subsystem
Definition at line 325 of file rte_eventdev.h.
#define RTE_EVENT_DEV_PRIORITY_NORMAL 128 |
Normal priority expressed across eventdev subsystem
Definition at line 330 of file rte_eventdev.h.
#define RTE_EVENT_DEV_PRIORITY_LOWEST 255 |
Lowest priority expressed across eventdev subsystem
Definition at line 335 of file rte_eventdev.h.
#define RTE_EVENT_QUEUE_WEIGHT_HIGHEST 255 |
Highest weight of an event queue
Definition at line 342 of file rte_eventdev.h.
#define RTE_EVENT_QUEUE_WEIGHT_LOWEST 0 |
Lowest weight of an event queue
Definition at line 346 of file rte_eventdev.h.
#define RTE_EVENT_QUEUE_AFFINITY_HIGHEST 255 |
Highest scheduling affinity of an event queue
Definition at line 352 of file rte_eventdev.h.
#define RTE_EVENT_QUEUE_AFFINITY_LOWEST 0 |
Lowest scheduling affinity of an event queue
Definition at line 356 of file rte_eventdev.h.
#define RTE_EVENT_DEV_ATTR_PORT_COUNT 0 |
The count of ports.
Definition at line 473 of file rte_eventdev.h.
#define RTE_EVENT_DEV_ATTR_QUEUE_COUNT 1 |
The count of queues.
Definition at line 477 of file rte_eventdev.h.
#define RTE_EVENT_DEV_ATTR_STARTED 2 |
The status of the device, zero for stopped, non-zero for started.
Definition at line 481 of file rte_eventdev.h.
#define RTE_EVENT_DEV_CFG_PER_DEQUEUE_TIMEOUT (1ULL << 0) |
Override the global dequeue_timeout_ns and use per dequeue timeout in ns.
Definition at line 501 of file rte_eventdev.h.
#define RTE_EVENT_QUEUE_CFG_ALL_TYPES (1ULL << 0) |
Allow ATOMIC,ORDERED,PARALLEL schedule type enqueue
Definition at line 606 of file rte_eventdev.h.
#define RTE_EVENT_QUEUE_CFG_SINGLE_LINK (1ULL << 1) |
This event queue links only to a single event port.
Definition at line 612 of file rte_eventdev.h.
#define RTE_EVENT_QUEUE_ATTR_PRIORITY 0 |
The priority of the queue.
Definition at line 726 of file rte_eventdev.h.
#define RTE_EVENT_QUEUE_ATTR_NB_ATOMIC_FLOWS 1 |
The number of atomic flows configured for the queue.
Definition at line 730 of file rte_eventdev.h.
#define RTE_EVENT_QUEUE_ATTR_NB_ATOMIC_ORDER_SEQUENCES 2 |
The number of atomic order sequences configured for the queue.
Definition at line 734 of file rte_eventdev.h.
#define RTE_EVENT_QUEUE_ATTR_EVENT_QUEUE_CFG 3 |
The cfg flags for the queue.
Definition at line 738 of file rte_eventdev.h.
#define RTE_EVENT_QUEUE_ATTR_SCHEDULE_TYPE 4 |
The schedule type of the queue.
Definition at line 742 of file rte_eventdev.h.
#define RTE_EVENT_QUEUE_ATTR_WEIGHT 5 |
The weight of the queue.
Definition at line 746 of file rte_eventdev.h.
#define RTE_EVENT_QUEUE_ATTR_AFFINITY 6 |
Affinity of the queue.
Definition at line 750 of file rte_eventdev.h.
#define RTE_EVENT_PORT_CFG_DISABLE_IMPL_REL (1ULL << 0) |
Configure the port not to release outstanding events in rte_event_dev_dequeue_burst(). If set, all events received through the port must be explicitly released with RTE_EVENT_OP_RELEASE or RTE_EVENT_OP_FORWARD. Must be unset if the device is not RTE_EVENT_DEV_CAP_IMPLICIT_RELEASE_DISABLE capable.
Definition at line 802 of file rte_eventdev.h.
#define RTE_EVENT_PORT_CFG_SINGLE_LINK (1ULL << 1) |
This event port links only to a single event queue.
Definition at line 809 of file rte_eventdev.h.
#define RTE_EVENT_PORT_CFG_HINT_PRODUCER (1ULL << 2) |
Hint that this event port will primarily enqueue events to the system. A PMD can optimize its internal workings by assuming that this port is primarily going to enqueue NEW events.
Note that this flag is only a hint, so PMDs must operate under the assumption that any port can enqueue an event with any type of op.
Definition at line 814 of file rte_eventdev.h.
#define RTE_EVENT_PORT_CFG_HINT_CONSUMER (1ULL << 3) |
Hint that this event port will primarily dequeue events from the system. A PMD can optimize its internal workings by assuming that this port is primarily going to consume events, and not enqueue FORWARD or RELEASE events.
Note that this flag is only a hint, so PMDs must operate under the assumption that any port can enqueue an event with any type of op.
Definition at line 824 of file rte_eventdev.h.
#define RTE_EVENT_PORT_CFG_HINT_WORKER (1ULL << 4) |
Hint that this event port will primarily pass existing events through. A PMD can optimize its internal workings by assuming that this port is primarily going to FORWARD events, and not enqueue NEW or RELEASE events often.
Note that this flag is only a hint, so PMDs must operate under the assumption that any port can enqueue an event with any type of op.
Definition at line 835 of file rte_eventdev.h.
#define RTE_EVENT_PORT_ATTR_ENQ_DEPTH 0 |
The queue depth of the port on the enqueue side
Definition at line 966 of file rte_eventdev.h.
#define RTE_EVENT_PORT_ATTR_DEQ_DEPTH 1 |
The queue depth of the port on the dequeue side
Definition at line 970 of file rte_eventdev.h.
#define RTE_EVENT_PORT_ATTR_NEW_EVENT_THRESHOLD 2 |
The new event threshold of the port
Definition at line 974 of file rte_eventdev.h.
#define RTE_EVENT_PORT_ATTR_IMPLICIT_RELEASE_DISABLE 3 |
The implicit release disable attribute of the port
Definition at line 978 of file rte_eventdev.h.
#define RTE_SCHED_TYPE_ORDERED 0 |
Ordered scheduling
Events from an ordered flow of an event queue can be scheduled to multiple ports for concurrent processing while maintaining the original event order. This scheme enables the user to achieve high single flow throughput by avoiding SW synchronization for ordering between ports which bound to cores.
The source flow ordering from an event queue is maintained when events are enqueued to their destination queue within the same ordered flow context. An event port holds the context until application call rte_event_dequeue_burst() from the same port, which implicitly releases the context. User may allow the scheduler to release the context earlier than that by invoking rte_event_enqueue_burst() with RTE_EVENT_OP_RELEASE operation.
Events from the source queue appear in their original order when dequeued from a destination queue. Event ordering is based on the received event(s), but also other (newly allocated or stored) events are ordered when enqueued within the same ordered context. Events not enqueued (e.g. released or stored) within the context are considered missing from reordering and are skipped at this time (but can be ordered again within another context).
Definition at line 1147 of file rte_eventdev.h.
#define RTE_SCHED_TYPE_ATOMIC 1 |
Atomic scheduling
Events from an atomic flow of an event queue can be scheduled only to a single port at a time. The port is guaranteed to have exclusive (atomic) access to the associated flow context, which enables the user to avoid SW synchronization. Atomic flows also help to maintain event ordering since only one port at a time can process events from a flow of an event queue.
The atomic queue synchronization context is dedicated to the port until application call rte_event_dequeue_burst() from the same port, which implicitly releases the context. User may allow the scheduler to release the context earlier than that by invoking rte_event_enqueue_burst() with RTE_EVENT_OP_RELEASE operation.
Definition at line 1174 of file rte_eventdev.h.
#define RTE_SCHED_TYPE_PARALLEL 2 |
Parallel scheduling
The scheduler performs priority scheduling, load balancing, etc. functions but does not provide additional event synchronization or ordering. It is free to schedule events from a single parallel flow of an event queue to multiple events ports for concurrent processing. The application is responsible for flow context synchronization and event ordering (SW synchronization).
Definition at line 1193 of file rte_eventdev.h.
#define RTE_EVENT_TYPE_ETHDEV 0x0 |
The event generated from ethdev subsystem
Definition at line 1207 of file rte_eventdev.h.
#define RTE_EVENT_TYPE_CRYPTODEV 0x1 |
The event generated from crypodev subsystem
Definition at line 1209 of file rte_eventdev.h.
#define RTE_EVENT_TYPE_TIMER 0x2 |
The event generated from event timer adapter
Definition at line 1211 of file rte_eventdev.h.
#define RTE_EVENT_TYPE_CPU 0x3 |
The event generated from cpu for pipelining. Application may use sub_event_type to further classify the event
Definition at line 1213 of file rte_eventdev.h.
#define RTE_EVENT_TYPE_ETH_RX_ADAPTER 0x4 |
The event generated from event eth Rx adapter
Definition at line 1217 of file rte_eventdev.h.
#define RTE_EVENT_TYPE_VECTOR 0x8 |
Indicates that event is a vector. All vector event types should be a logical OR of EVENT_TYPE_VECTOR. This simplifies the pipeline design as one can split processing the events between vector events and normal event across event types. Example: if (ev.event_type & RTE_EVENT_TYPE_VECTOR) { // Classify and handle vector event. } else { // Classify and handle event. }
Definition at line 1219 of file rte_eventdev.h.
#define RTE_EVENT_TYPE_ETHDEV_VECTOR (RTE_EVENT_TYPE_VECTOR | RTE_EVENT_TYPE_ETHDEV) |
The event vector generated from ethdev subsystem
Definition at line 1231 of file rte_eventdev.h.
#define RTE_EVENT_TYPE_CPU_VECTOR (RTE_EVENT_TYPE_VECTOR | RTE_EVENT_TYPE_CPU) |
The event vector generated from cpu for pipelining.
Definition at line 1234 of file rte_eventdev.h.
#define RTE_EVENT_TYPE_ETH_RX_ADAPTER_VECTOR (RTE_EVENT_TYPE_VECTOR | RTE_EVENT_TYPE_ETH_RX_ADAPTER) |
The event vector generated from eth Rx adapter.
Definition at line 1236 of file rte_eventdev.h.
#define RTE_EVENT_TYPE_CRYPTODEV_VECTOR (RTE_EVENT_TYPE_VECTOR | RTE_EVENT_TYPE_CRYPTODEV) |
The event vector generated from cryptodev adapter.
Definition at line 1239 of file rte_eventdev.h.
#define RTE_EVENT_TYPE_MAX 0x10 |
Maximum number of event types
Definition at line 1243 of file rte_eventdev.h.
#define RTE_EVENT_OP_NEW 0 |
The event producers use this operation to inject a new event to the event device.
Definition at line 1247 of file rte_eventdev.h.
#define RTE_EVENT_OP_FORWARD 1 |
The CPU use this operation to forward the event to different event queue or change to new application specific flow or schedule type to enable pipelining.
This operation must only be enqueued to the same port that the event to be forwarded was dequeued from.
Definition at line 1251 of file rte_eventdev.h.
#define RTE_EVENT_OP_RELEASE 2 |
Release the flow context associated with the schedule type.
If current flow's scheduler type method is RTE_SCHED_TYPE_ATOMIC then this function hints the scheduler that the user has completed critical section processing in the current atomic context. The scheduler is now allowed to schedule events from the same flow from an event queue to another port. However, the context may be still held until the next rte_event_dequeue_burst() call, this call allows but does not force the scheduler to release the context early.
Early atomic context release may increase parallelism and thus system performance, but the user needs to design carefully the split into critical vs non-critical sections.
If current flow's scheduler type method is RTE_SCHED_TYPE_ORDERED then this function hints the scheduler that the user has done all that need to maintain event order in the current ordered context. The scheduler is allowed to release the ordered context of this port and avoid reordering any following enqueues.
Early ordered context release may increase parallelism and thus system performance.
If current flow's scheduler type method is RTE_SCHED_TYPE_PARALLEL or no scheduling context is held then this function may be an NOOP, depending on the implementation.
This operation must only be enqueued to the same port that the event to be released was dequeued from.
Definition at line 1259 of file rte_eventdev.h.
#define RTE_EVENT_ETH_RX_ADAPTER_CAP_INTERNAL_PORT 0x1 |
This flag is sent when the packet transfer mechanism is in HW. Ethdev can send packets to the event device using internal event port.
Definition at line 1371 of file rte_eventdev.h.
#define RTE_EVENT_ETH_RX_ADAPTER_CAP_MULTI_EVENTQ 0x2 |
Adapter supports multiple event queues per ethdev. Every ethdev Rx queue can be connected to a unique event queue.
Definition at line 1375 of file rte_eventdev.h.
#define RTE_EVENT_ETH_RX_ADAPTER_CAP_OVERRIDE_FLOW_ID 0x4 |
The application can override the adapter generated flow ID in the event. This flow ID can be specified when adding an ethdev Rx queue to the adapter using the ev.flow_id member.
Definition at line 1379 of file rte_eventdev.h.
#define RTE_EVENT_ETH_RX_ADAPTER_CAP_EVENT_VECTOR 0x8 |
Adapter supports event vectorization per ethdev.
Definition at line 1386 of file rte_eventdev.h.
#define RTE_EVENT_TIMER_ADAPTER_CAP_INTERNAL_PORT (1ULL << 0) |
This flag is set when the timer mechanism is in HW.
Definition at line 1412 of file rte_eventdev.h.
#define RTE_EVENT_TIMER_ADAPTER_CAP_PERIODIC (1ULL << 1) |
This flag is set if periodic mode is supported.
Definition at line 1415 of file rte_eventdev.h.
#define RTE_EVENT_CRYPTO_ADAPTER_CAP_INTERNAL_PORT_OP_NEW 0x1 |
Flag indicates HW is capable of generating events in RTE_EVENT_OP_NEW enqueue operation. Cryptodev will send packets to the event device as new events using an internal event port.
Definition at line 1435 of file rte_eventdev.h.
#define RTE_EVENT_CRYPTO_ADAPTER_CAP_INTERNAL_PORT_OP_FWD 0x2 |
Flag indicates HW is capable of generating events in RTE_EVENT_OP_FORWARD enqueue operation. Cryptodev will send packets to the event device as forwarded event using an internal event port.
Definition at line 1442 of file rte_eventdev.h.
#define RTE_EVENT_CRYPTO_ADAPTER_CAP_INTERNAL_PORT_QP_EV_BIND 0x4 |
Flag indicates HW is capable of mapping crypto queue pair to event queue.
Definition at line 1449 of file rte_eventdev.h.
#define RTE_EVENT_CRYPTO_ADAPTER_CAP_SESSION_PRIVATE_DATA 0x8 |
Flag indicates HW/SW supports a mechanism to store and retrieve the private data information along with the crypto session.
Definition at line 1454 of file rte_eventdev.h.
#define RTE_EVENT_CRYPTO_ADAPTER_CAP_EVENT_VECTOR 0x10 |
Flag indicates HW is capable of aggregating processed crypto operations into rte_event_vector.
Definition at line 1459 of file rte_eventdev.h.
#define RTE_EVENT_ETH_TX_ADAPTER_CAP_INTERNAL_PORT 0x1 |
This flag is sent when the PMD supports a packet transmit callback
Definition at line 1489 of file rte_eventdev.h.
#define RTE_EVENT_ETH_TX_ADAPTER_CAP_EVENT_VECTOR 0x2 |
Indicates that the Tx adapter is capable of handling event vector of mbufs.
Definition at line 1492 of file rte_eventdev.h.
#define RTE_EVENT_DEV_XSTATS_NAME_SIZE 64 |
Maximum name length for extended statistics counters
Definition at line 1745 of file rte_eventdev.h.
#define RTE_EVENT_DEV_MAINT_OP_FLUSH (1 << 0) |
Force an immediately flush of any buffered events in the port, potentially at the cost of additional overhead.
Definition at line 2225 of file rte_eventdev.h.
typedef void(* rte_eventdev_port_flush_t) (uint8_t dev_id, struct rte_event event, void *arg) |
Callback function prototype that can be passed during rte_event_port_release(), invoked once per a released event.
Definition at line 927 of file rte_eventdev.h.
typedef void(* rte_eventdev_stop_flush_t) (uint8_t dev_id, struct rte_event event, void *arg) |
Callback function called during rte_event_dev_stop(), invoked once per flushed event.
Definition at line 1040 of file rte_eventdev.h.
Selects the component of the eventdev to retrieve statistics from.
Definition at line 1750 of file rte_eventdev.h.
uint8_t rte_event_dev_count | ( | void | ) |
Get the total number of event devices that have been successfully initialised.
int rte_event_dev_get_dev_id | ( | const char * | name | ) |
Get the device identifier for the named event device.
name | Event device name to select the event device identifier. |
int rte_event_dev_socket_id | ( | uint8_t | dev_id | ) |
Return the NUMA socket to which a device is connected.
dev_id | The identifier of the device. |
int rte_event_dev_info_get | ( | uint8_t | dev_id, |
struct rte_event_dev_info * | dev_info | ||
) |
Retrieve the contextual information of an event device.
dev_id | The identifier of the device. | |
[out] | dev_info | A pointer to a structure of type rte_event_dev_info to be filled with the contextual information of the device. |
int rte_event_dev_attr_get | ( | uint8_t | dev_id, |
uint32_t | attr_id, | ||
uint32_t * | attr_value | ||
) |
Get an attribute from a device.
dev_id | Eventdev id | |
attr_id | The attribute ID to retrieve | |
[out] | attr_value | A pointer that will be filled in with the attribute value if successful. |
int rte_event_dev_configure | ( | uint8_t | dev_id, |
const struct rte_event_dev_config * | dev_conf | ||
) |
Configure an event device.
This function must be invoked first before any other function in the API. This function can also be re-invoked when a device is in the stopped state.
The caller may use rte_event_dev_info_get() to get the capability of each resources available for this event device.
dev_id | The identifier of the device to configure. |
dev_conf | The event device configuration structure. |
int rte_event_queue_default_conf_get | ( | uint8_t | dev_id, |
uint8_t | queue_id, | ||
struct rte_event_queue_conf * | queue_conf | ||
) |
Retrieve the default configuration information of an event queue designated by its queue_id from the event driver for an event device.
This function intended to be used in conjunction with rte_event_queue_setup() where caller needs to set up the queue by overriding few default values.
dev_id | The identifier of the device. | |
queue_id | The index of the event queue to get the configuration information. The value must be in the range [0, nb_event_queues - 1] previously supplied to rte_event_dev_configure(). | |
[out] | queue_conf | The pointer to the default event queue configuration data. |
int rte_event_queue_setup | ( | uint8_t | dev_id, |
uint8_t | queue_id, | ||
const struct rte_event_queue_conf * | queue_conf | ||
) |
Allocate and set up an event queue for an event device.
dev_id | The identifier of the device. |
queue_id | The index of the event queue to setup. The value must be in the range [0, nb_event_queues - 1] previously supplied to rte_event_dev_configure(). |
queue_conf | The pointer to the configuration data to be used for the event queue. NULL value is allowed, in which case default configuration used. |
int rte_event_queue_attr_get | ( | uint8_t | dev_id, |
uint8_t | queue_id, | ||
uint32_t | attr_id, | ||
uint32_t * | attr_value | ||
) |
Get an attribute from a queue.
dev_id | Eventdev id | |
queue_id | Eventdev queue id | |
attr_id | The attribute ID to retrieve | |
[out] | attr_value | A pointer that will be filled in with the attribute value if successful |
__rte_experimental int rte_event_queue_attr_set | ( | uint8_t | dev_id, |
uint8_t | queue_id, | ||
uint32_t | attr_id, | ||
uint64_t | attr_value | ||
) |
Set an event queue attribute.
dev_id | Eventdev id |
queue_id | Eventdev queue id |
attr_id | The attribute ID to set |
attr_value | The attribute value to set |
int rte_event_port_default_conf_get | ( | uint8_t | dev_id, |
uint8_t | port_id, | ||
struct rte_event_port_conf * | port_conf | ||
) |
Retrieve the default configuration information of an event port designated by its port_id from the event driver for an event device.
This function intended to be used in conjunction with rte_event_port_setup() where caller needs to set up the port by overriding few default values.
dev_id | The identifier of the device. | |
port_id | The index of the event port to get the configuration information. The value must be in the range [0, nb_event_ports - 1] previously supplied to rte_event_dev_configure(). | |
[out] | port_conf | The pointer to the default event port configuration data |
int rte_event_port_setup | ( | uint8_t | dev_id, |
uint8_t | port_id, | ||
const struct rte_event_port_conf * | port_conf | ||
) |
Allocate and set up an event port for an event device.
dev_id | The identifier of the device. |
port_id | The index of the event port to setup. The value must be in the range [0, nb_event_ports - 1] previously supplied to rte_event_dev_configure(). |
port_conf | The pointer to the configuration data to be used for the queue. NULL value is allowed, in which case default configuration used. |
__rte_experimental void rte_event_port_quiesce | ( | uint8_t | dev_id, |
uint8_t | port_id, | ||
rte_eventdev_port_flush_t | release_cb, | ||
void * | args | ||
) |
Quiesce any core specific resources consumed by the event port.
Event ports are generally coupled with lcores, and a given Hardware implementation might require the PMD to store port specific data in the lcore. When the application decides to migrate the event port to another lcore or teardown the current lcore it may to call rte_event_port_quiesce
to make sure that all the data associated with the event port are released from the lcore, this might also include any prefetched events. While releasing the event port from the lcore, this function calls the user-provided flush callback once per event.
dev_id | The identifier of the device. |
port_id | The index of the event port to setup. The value must be in the range [0, nb_event_ports - 1] previously supplied to rte_event_dev_configure(). |
release_cb | Callback function invoked once per flushed event. |
args | Argument supplied to callback. |
int rte_event_port_attr_get | ( | uint8_t | dev_id, |
uint8_t | port_id, | ||
uint32_t | attr_id, | ||
uint32_t * | attr_value | ||
) |
Get an attribute from a port.
dev_id | Eventdev id | |
port_id | Eventdev port id | |
attr_id | The attribute ID to retrieve | |
[out] | attr_value | A pointer that will be filled in with the attribute value if successful |
int rte_event_dev_start | ( | uint8_t | dev_id | ) |
Start an event device.
The device start step is the last one and consists of setting the event queues to start accepting the events and schedules to event ports.
On success, all basic functions exported by the API (event enqueue, event dequeue and so on) can be invoked.
dev_id | Event device identifier |
void rte_event_dev_stop | ( | uint8_t | dev_id | ) |
Stop an event device.
This function causes all queued events to be drained, including those residing in event ports. While draining events out of the device, this function calls the user-provided flush callback (if one was registered) once per event.
The device can be restarted with a call to rte_event_dev_start(). Threads that continue to enqueue/dequeue while the device is stopped, or being stopped, will result in undefined behavior. This includes event adapters, which must be stopped prior to stopping the eventdev.
dev_id | Event device identifier. |
int rte_event_dev_stop_flush_callback_register | ( | uint8_t | dev_id, |
rte_eventdev_stop_flush_t | callback, | ||
void * | userdata | ||
) |
Registers a callback function to be invoked during rte_event_dev_stop() for each flushed event. This function can be used to properly dispose of queued events, for example events containing memory pointers.
The callback function is only registered for the calling process. The callback function must be registered in every process that can call rte_event_dev_stop().
To unregister a callback, call this function with a NULL callback pointer.
dev_id | The identifier of the device. |
callback | Callback function invoked once per flushed event. |
userdata | Argument supplied to callback. |
int rte_event_dev_close | ( | uint8_t | dev_id | ) |
Close an event device. The device cannot be restarted!
dev_id | Event device identifier |
int rte_event_eth_rx_adapter_caps_get | ( | uint8_t | dev_id, |
uint16_t | eth_port_id, | ||
uint32_t * | caps | ||
) |
Retrieve the event device's ethdev Rx adapter capabilities for the specified ethernet port
dev_id | The identifier of the device. | |
eth_port_id | The identifier of the ethernet device. | |
[out] | caps | A pointer to memory filled with Rx event adapter capabilities. |
int rte_event_timer_adapter_caps_get | ( | uint8_t | dev_id, |
uint32_t * | caps | ||
) |
Retrieve the event device's timer adapter capabilities.
dev_id | The identifier of the device. | |
[out] | caps | A pointer to memory to be filled with event timer adapter capabilities. |
int rte_event_crypto_adapter_caps_get | ( | uint8_t | dev_id, |
uint8_t | cdev_id, | ||
uint32_t * | caps | ||
) |
Retrieve the event device's crypto adapter capabilities for the specified cryptodev device
dev_id | The identifier of the device. | |
cdev_id | The identifier of the cryptodev device. | |
[out] | caps | A pointer to memory filled with event adapter capabilities. It is expected to be pre-allocated & initialized by caller. |
int rte_event_eth_tx_adapter_caps_get | ( | uint8_t | dev_id, |
uint16_t | eth_port_id, | ||
uint32_t * | caps | ||
) |
Retrieve the event device's eth Tx adapter capabilities
dev_id | The identifier of the device. | |
eth_port_id | The identifier of the ethernet device. | |
[out] | caps | A pointer to memory filled with eth Tx adapter capabilities. |
int rte_event_dequeue_timeout_ticks | ( | uint8_t | dev_id, |
uint64_t | ns, | ||
uint64_t * | timeout_ticks | ||
) |
Converts nanoseconds to timeout_ticks value for rte_event_dequeue_burst()
If the device is configured with RTE_EVENT_DEV_CFG_PER_DEQUEUE_TIMEOUT flag then application can use this function to convert timeout value in nanoseconds to implementations specific timeout value supplied in rte_event_dequeue_burst()
dev_id | The identifier of the device. | |
ns | Wait time in nanosecond | |
[out] | timeout_ticks | Value for the timeout_ticks parameter in rte_event_dequeue_burst() |
int rte_event_port_link | ( | uint8_t | dev_id, |
uint8_t | port_id, | ||
const uint8_t | queues[], | ||
const uint8_t | priorities[], | ||
uint16_t | nb_links | ||
) |
Link multiple source event queues supplied in queues to the destination event port designated by its port_id with associated service priority supplied in priorities on the event device designated by its dev_id.
The link establishment shall enable the event port port_id from receiving events from the specified event queue(s) supplied in queues
An event queue may link to one or more event ports. The number of links can be established from an event queue to event port is implementation defined.
Event queue(s) to event port link establishment can be changed at runtime without re-configuring the device to support scaling and to reduce the latency of critical work by establishing the link with more event ports at runtime.
dev_id | The identifier of the device. |
port_id | Event port identifier to select the destination port to link. |
queues | Points to an array of nb_links event queues to be linked to the event port. NULL value is allowed, in which case this function links all the configured event queues nb_event_queues which previously supplied to rte_event_dev_configure() to the event port port_id |
priorities | Points to an array of nb_links service priorities associated with each event queue link to event port. The priority defines the event port's servicing priority for event queue, which may be ignored by an implementation. The requested priority should in the range of [RTE_EVENT_DEV_PRIORITY_HIGHEST, RTE_EVENT_DEV_PRIORITY_LOWEST]. The implementation shall normalize the requested priority to implementation supported priority value. NULL value is allowed, in which case this function links the event queues with RTE_EVENT_DEV_PRIORITY_NORMAL servicing priority |
nb_links | The number of links to establish. This parameter is ignored if queues is NULL. |
int rte_event_port_unlink | ( | uint8_t | dev_id, |
uint8_t | port_id, | ||
uint8_t | queues[], | ||
uint16_t | nb_unlinks | ||
) |
Unlink multiple source event queues supplied in queues from the destination event port designated by its port_id on the event device designated by its dev_id.
The unlink call issues an async request to disable the event port port_id from receiving events from the specified event queue queue_id. Event queue(s) to event port unlink establishment can be changed at runtime without re-configuring the device.
dev_id | The identifier of the device. |
port_id | Event port identifier to select the destination port to unlink. |
queues | Points to an array of nb_unlinks event queues to be unlinked from the event port. NULL value is allowed, in which case this function unlinks all the event queue(s) from the event port port_id. |
nb_unlinks | The number of unlinks to establish. This parameter is ignored if queues is NULL. |
int rte_event_port_unlinks_in_progress | ( | uint8_t | dev_id, |
uint8_t | port_id | ||
) |
Returns the number of unlinks in progress.
This function provides the application with a method to detect when an unlink has been completed by the implementation.
dev_id | The identifier of the device. |
port_id | Event port identifier to select port to check for unlinks in progress. |
int rte_event_port_links_get | ( | uint8_t | dev_id, |
uint8_t | port_id, | ||
uint8_t | queues[], | ||
uint8_t | priorities[] | ||
) |
Retrieve the list of source event queues and its associated service priority linked to the destination event port designated by its port_id on the event device designated by its dev_id.
dev_id | The identifier of the device. | |
port_id | Event port identifier. | |
[out] | queues | Points to an array of queues for output. The caller has to allocate RTE_EVENT_MAX_QUEUES_PER_DEV bytes to store the event queue(s) linked with event port port_id |
[out] | priorities | Points to an array of priorities for output. The caller has to allocate RTE_EVENT_MAX_QUEUES_PER_DEV bytes to store the service priority associated with each event queue linked |
int rte_event_dev_service_id_get | ( | uint8_t | dev_id, |
uint32_t * | service_id | ||
) |
Retrieve the service ID of the event dev. If the adapter doesn't use a rte_service function, this function returns -ESRCH.
dev_id | The identifier of the device. | |
[out] | service_id | A pointer to a uint32_t, to be filled in with the service id. |
int rte_event_dev_dump | ( | uint8_t | dev_id, |
FILE * | f | ||
) |
Dump internal information about dev_id to the FILE* provided in f.
dev_id | The identifier of the device. |
f | A pointer to a file for output |
int rte_event_dev_xstats_names_get | ( | uint8_t | dev_id, |
enum rte_event_dev_xstats_mode | mode, | ||
uint8_t | queue_port_id, | ||
struct rte_event_dev_xstats_name * | xstats_names, | ||
uint64_t * | ids, | ||
unsigned int | size | ||
) |
Retrieve names of extended statistics of an event device.
dev_id | The identifier of the event device. | |
mode | The mode of statistics to retrieve. Choices include the device statistics, port statistics or queue statistics. | |
queue_port_id | Used to specify the port or queue number in queue or port mode, and is ignored in device mode. | |
[out] | xstats_names | Block of memory to insert names into. Must be at least size in capacity. If set to NULL, function returns required capacity. |
[out] | ids | Block of memory to insert ids into. Must be at least size in capacity. If set to NULL, function returns required capacity. The id values returned can be passed to rte_event_dev_xstats_get to select statistics. |
size | Capacity of xstats_names (number of names). |
int rte_event_dev_xstats_get | ( | uint8_t | dev_id, |
enum rte_event_dev_xstats_mode | mode, | ||
uint8_t | queue_port_id, | ||
const uint64_t | ids[], | ||
uint64_t | values[], | ||
unsigned int | n | ||
) |
Retrieve extended statistics of an event device.
dev_id | The identifier of the device. | |
mode | The mode of statistics to retrieve. Choices include the device statistics, port statistics or queue statistics. | |
queue_port_id | Used to specify the port or queue number in queue or port mode, and is ignored in device mode. | |
ids | The id numbers of the stats to get. The ids can be got from the stat position in the stat list from rte_event_dev_get_xstats_names(), or by using rte_event_dev_xstats_by_name_get(). | |
[out] | values | The values for each stats request by ID. |
n | The number of stats requested |
uint64_t rte_event_dev_xstats_by_name_get | ( | uint8_t | dev_id, |
const char * | name, | ||
uint64_t * | id | ||
) |
Retrieve the value of a single stat by requesting it by name.
dev_id | The identifier of the device | |
name | The stat name to retrieve | |
[out] | id | If non-NULL, the numerical id of the stat will be returned, so that further requests for the stat can be got using rte_event_dev_xstats_get, which will be faster as it doesn't need to scan a list of names for the stat. If the stat cannot be found, the id returned will be (unsigned)-1. |
int rte_event_dev_xstats_reset | ( | uint8_t | dev_id, |
enum rte_event_dev_xstats_mode | mode, | ||
int16_t | queue_port_id, | ||
const uint64_t | ids[], | ||
uint32_t | nb_ids | ||
) |
Reset the values of the xstats of the selected component in the device.
dev_id | The identifier of the device |
mode | The mode of the statistics to reset. Choose from device, queue or port. |
queue_port_id | The queue or port to reset. 0 and positive values select ports and queues, while -1 indicates all ports or queues. |
ids | Selects specific statistics to be reset. When NULL, all statistics selected by mode will be reset. If non-NULL, must point to array of at least nb_ids size. |
nb_ids | The number of ids available from the ids array. Ignored when ids is NULL. |
int rte_event_dev_selftest | ( | uint8_t | dev_id | ) |
Trigger the eventdev self test.
dev_id | The identifier of the device |
struct rte_mempool* rte_event_vector_pool_create | ( | const char * | name, |
unsigned int | n, | ||
unsigned int | cache_size, | ||
uint16_t | nb_elem, | ||
int | socket_id | ||
) |
Get the memory required per event vector based on the number of elements per vector. This should be used to create the mempool that holds the event vectors.
name | The name of the vector pool. |
n | The number of elements in the mbuf pool. |
cache_size | Size of the per-core object cache. See rte_mempool_create() for details. |
nb_elem | The number of elements that a single event vector should be able to hold. |
socket_id | The socket identifier where the memory should be allocated. The value can be SOCKET_ID_ANY if there is no NUMA constraint for the reserved zone |
|
inlinestatic |
Enqueue a burst of events objects or an event object supplied in rte_event structure on an event device designated by its dev_id through the event port specified by port_id. Each event object specifies the event queue on which it will be enqueued.
The nb_events parameter is the number of event objects to enqueue which are supplied in the ev array of rte_event structure.
Event operations RTE_EVENT_OP_FORWARD and RTE_EVENT_OP_RELEASE must only be enqueued to the same port that their associated events were dequeued from.
The rte_event_enqueue_burst() function returns the number of events objects it actually enqueued. A return value equal to nb_events means that all event objects have been enqueued.
dev_id | The identifier of the device. |
port_id | The identifier of the event port. |
ev | Points to an array of nb_events objects of type rte_event structure which contain the event object enqueue operations to be processed. |
nb_events | The number of event objects to enqueue, typically number of rte_event_port_attr_get(...RTE_EVENT_PORT_ATTR_ENQ_DEPTH...) available for this port. |
Definition at line 2012 of file rte_eventdev.h.
|
inlinestatic |
Enqueue a burst of events objects of operation type RTE_EVENT_OP_NEW on an event device designated by its dev_id through the event port specified by port_id.
Provides the same functionality as rte_event_enqueue_burst(), expect that application can use this API when the all objects in the burst contains the enqueue operation of the type RTE_EVENT_OP_NEW. This specialized function can provide the additional hint to the PMD and optimize if possible.
The rte_event_enqueue_new_burst() result is undefined if the enqueue burst has event object of operation type != RTE_EVENT_OP_NEW.
dev_id | The identifier of the device. |
port_id | The identifier of the event port. |
ev | Points to an array of nb_events objects of type rte_event structure which contain the event object enqueue operations to be processed. |
nb_events | The number of event objects to enqueue, typically number of rte_event_port_attr_get(...RTE_EVENT_PORT_ATTR_ENQ_DEPTH...) available for this port. |
Definition at line 2064 of file rte_eventdev.h.
|
inlinestatic |
Enqueue a burst of events objects of operation type RTE_EVENT_OP_FORWARD on an event device designated by its dev_id through the event port specified by port_id.
Provides the same functionality as rte_event_enqueue_burst(), expect that application can use this API when the all objects in the burst contains the enqueue operation of the type RTE_EVENT_OP_FORWARD. This specialized function can provide the additional hint to the PMD and optimize if possible.
The rte_event_enqueue_new_burst() result is undefined if the enqueue burst has event object of operation type != RTE_EVENT_OP_FORWARD.
dev_id | The identifier of the device. |
port_id | The identifier of the event port. |
ev | Points to an array of nb_events objects of type rte_event structure which contain the event object enqueue operations to be processed. |
nb_events | The number of event objects to enqueue, typically number of rte_event_port_attr_get(...RTE_EVENT_PORT_ATTR_ENQ_DEPTH...) available for this port. |
Definition at line 2116 of file rte_eventdev.h.
|
inlinestatic |
Dequeue a burst of events objects or an event object from the event port designated by its event_port_id, on an event device designated by its dev_id.
rte_event_dequeue_burst() does not dictate the specifics of scheduling algorithm as each eventdev driver may have different criteria to schedule an event. However, in general, from an application perspective scheduler may use the following scheme to dispatch an event to the port.
1) Selection of event queue based on a) The list of event queues are linked to the event port. b) If the device has RTE_EVENT_DEV_CAP_QUEUE_QOS capability then event queue selection from list is based on event queue priority relative to other event queue supplied as priority in rte_event_queue_setup() c) If the device has RTE_EVENT_DEV_CAP_EVENT_QOS capability then event queue selection from the list is based on event priority supplied as priority in rte_event_enqueue_burst() 2) Selection of event a) The number of flows available in selected event queue. b) Schedule type method associated with the event
The nb_events parameter is the maximum number of event objects to dequeue which are returned in the ev array of rte_event structure.
The rte_event_dequeue_burst() function returns the number of events objects it actually dequeued. A return value equal to nb_events means that all event objects have been dequeued.
The number of events dequeued is the number of scheduler contexts held by this port. These contexts are automatically released in the next rte_event_dequeue_burst() invocation if the port supports implicit releases, or invoking rte_event_enqueue_burst() with RTE_EVENT_OP_RELEASE operation can be used to release the contexts early.
Event operations RTE_EVENT_OP_FORWARD and RTE_EVENT_OP_RELEASE must only be enqueued to the same port that their associated events were dequeued from.
dev_id | The identifier of the device. | |
port_id | The identifier of the event port. | |
[out] | ev | Points to an array of nb_events objects of type rte_event structure for output to be populated with the dequeued event objects. |
nb_events | The maximum number of event objects to dequeue, typically number of rte_event_port_dequeue_depth() available for this port. | |
timeout_ticks |
|
Definition at line 2193 of file rte_eventdev.h.
|
inlinestatic |
Maintain an event device.
This function is only relevant for event devices which do not have the RTE_EVENT_DEV_CAP_MAINTENANCE_FREE flag set. Such devices require an application thread using a particular port to periodically call rte_event_maintain() on that port during periods which it is neither attempting to enqueue events to nor dequeue events from the port. rte_event_maintain() is a low-overhead function and should be called at a high rate (e.g., in the application's poll loop).
No port may be left unmaintained.
At the application thread's convenience, rte_event_maintain() may (but is not required to) be called even during periods when enqueue or dequeue functions are being called, at the cost of a slight increase in overhead.
rte_event_maintain() may be called on event devices which have set RTE_EVENT_DEV_CAP_MAINTENANCE_FREE, in which case it is a no-operation.
dev_id | The identifier of the device. |
port_id | The identifier of the event port. |
op | 0, or RTE_EVENT_DEV_MAINT_OP_FLUSH. |
Definition at line 2269 of file rte_eventdev.h.