#include <rte_ethdev.h>

Data Fields
uint32_t	link_speeds
struct rte_eth_rxmode	rxmode
struct rte_eth_txmode	txmode
uint32_t	lpbk_mode
struct {
struct rte_eth_rss_conf rss_conf
struct rte_eth_vmdq_dcb_conf vmdq_dcb_conf
struct rte_eth_dcb_rx_conf dcb_rx_conf
struct rte_eth_vmdq_rx_conf vmdq_rx_conf
}	rx_adv_conf
union {
struct rte_eth_vmdq_dcb_tx_conf vmdq_dcb_tx_conf
struct rte_eth_dcb_tx_conf dcb_tx_conf
struct rte_eth_vmdq_tx_conf vmdq_tx_conf
}	tx_adv_conf
uint32_t	dcb_capability_en
struct rte_fdir_conf	fdir_conf
struct rte_intr_conf	intr_conf

Detailed Description

A structure used to configure an Ethernet port. Depending upon the RX multi-queue mode, extra advanced configuration settings may be needed.

Examples:: bond/main.c, distributor/main.c, dpdk_qat/main.c, ethtool/ethtool-app/main.c, exception_path/main.c, ip_fragmentation/main.c, ip_reassembly/main.c, ipv4_multicast/main.c, kni/main.c, l2fwd-crypto/main.c, l2fwd-ivshmem/host/host.c, l2fwd-jobstats/main.c, l2fwd-keepalive/main.c, l2fwd/main.c, l3fwd-acl/main.c, l3fwd-power/main.c, l3fwd-vf/main.c, l3fwd/main.c, link_status_interrupt/main.c, load_balancer/init.c, multi_process/client_server_mp/mp_server/init.c, multi_process/l2fwd_fork/main.c, multi_process/symmetric_mp/main.c, netmap_compat/bridge/bridge.c, netmap_compat/lib/compat_netmap.c, packet_ordering/main.c, performance-thread/l3fwd-thread/main.c, ptpclient/ptpclient.c, qos_meter/main.c, qos_sched/init.c, quota_watermark/qw/init.c, rxtx_callbacks/main.c, skeleton/basicfwd.c, tep_termination/vxlan_setup.c, vhost/main.c, vhost_xen/main.c, vmdq/main.c, and vmdq_dcb/main.c.

Definition at line 810 of file rte_ethdev.h.

Field Documentation

uint32_t link_speeds

bitmap of ETH_LINK_SPEED_XXX of speeds to be used. ETH_LINK_SPEED_FIXED disables link autonegotiation, and a unique speed shall be set. Otherwise, the bitmap defines the set of speeds to be advertised. If the special value ETH_LINK_SPEED_AUTONEG (0) is used, all speeds supported are advertised.

Definition at line 811 of file rte_ethdev.h.

struct rte_eth_rxmode rxmode

Port RX configuration.

Examples:: bond/main.c, distributor/main.c, dpdk_qat/main.c, exception_path/main.c, ip_fragmentation/main.c, ip_reassembly/main.c, ipv4_multicast/main.c, kni/main.c, l2fwd-crypto/main.c, l2fwd-ivshmem/host/host.c, l2fwd-jobstats/main.c, l2fwd-keepalive/main.c, l2fwd/main.c, l3fwd-acl/main.c, l3fwd-power/main.c, l3fwd-vf/main.c, l3fwd/main.c, link_status_interrupt/main.c, load_balancer/init.c, multi_process/client_server_mp/mp_server/init.c, multi_process/l2fwd_fork/main.c, multi_process/symmetric_mp/main.c, netmap_compat/bridge/bridge.c, performance-thread/l3fwd-thread/main.c, ptpclient/ptpclient.c, qos_meter/main.c, qos_sched/init.c, quota_watermark/qw/init.c, rxtx_callbacks/main.c, skeleton/basicfwd.c, tep_termination/vxlan_setup.c, vhost/main.c, vhost_xen/main.c, vmdq/main.c, and vmdq_dcb/main.c.

Definition at line 818 of file rte_ethdev.h.

struct rte_eth_txmode txmode

Port TX configuration.

Definition at line 819 of file rte_ethdev.h.

uint32_t lpbk_mode

Loopback operation mode. By default the value is 0, meaning the loopback mode is disabled. Read the datasheet of given ethernet controller for details. The possible values of this field are defined in implementation of each driver.

Definition at line 820 of file rte_ethdev.h.

struct rte_eth_rss_conf rss_conf

Port RSS configuration