18. Intel(R) QuickAssist (QAT) Crypto Poll Mode Driver

QAT documentation consists of three parts:

  • Details of the symmetric and asymmetric crypto services below.
  • Details of the compression service in the compressdev drivers section.
  • Details of building the common QAT infrastructure and the PMDs to support the above services. See Building PMDs on QAT below.

18.1. Symmetric Crypto Service on QAT

The QAT symmetric crypto PMD (hereafter referred to as QAT SYM [PMD]) provides poll mode crypto driver support for the following hardware accelerator devices:

  • Intel QuickAssist Technology DH895xCC
  • Intel QuickAssist Technology C62x
  • Intel QuickAssist Technology C3xxx
  • Intel QuickAssist Technology 200xx
  • Intel QuickAssist Technology D15xx
  • Intel QuickAssist Technology C4xxx

18.1.1. Features

The QAT SYM PMD has support for:

Cipher algorithms:

  • RTE_CRYPTO_CIPHER_3DES_CBC
  • RTE_CRYPTO_CIPHER_3DES_CTR
  • RTE_CRYPTO_CIPHER_AES128_CBC
  • RTE_CRYPTO_CIPHER_AES192_CBC
  • RTE_CRYPTO_CIPHER_AES256_CBC
  • RTE_CRYPTO_CIPHER_AES128_CTR
  • RTE_CRYPTO_CIPHER_AES192_CTR
  • RTE_CRYPTO_CIPHER_AES256_CTR
  • RTE_CRYPTO_CIPHER_AES_XTS
  • RTE_CRYPTO_CIPHER_SNOW3G_UEA2
  • RTE_CRYPTO_CIPHER_NULL
  • RTE_CRYPTO_CIPHER_KASUMI_F8
  • RTE_CRYPTO_CIPHER_DES_CBC
  • RTE_CRYPTO_CIPHER_AES_DOCSISBPI
  • RTE_CRYPTO_CIPHER_DES_DOCSISBPI
  • RTE_CRYPTO_CIPHER_ZUC_EEA3

Hash algorithms:

  • RTE_CRYPTO_AUTH_SHA1
  • RTE_CRYPTO_AUTH_SHA1_HMAC
  • RTE_CRYPTO_AUTH_SHA224
  • RTE_CRYPTO_AUTH_SHA224_HMAC
  • RTE_CRYPTO_AUTH_SHA256
  • RTE_CRYPTO_AUTH_SHA256_HMAC
  • RTE_CRYPTO_AUTH_SHA384
  • RTE_CRYPTO_AUTH_SHA384_HMAC
  • RTE_CRYPTO_AUTH_SHA512
  • RTE_CRYPTO_AUTH_SHA512_HMAC
  • RTE_CRYPTO_AUTH_AES_XCBC_MAC
  • RTE_CRYPTO_AUTH_SNOW3G_UIA2
  • RTE_CRYPTO_AUTH_MD5_HMAC
  • RTE_CRYPTO_AUTH_NULL
  • RTE_CRYPTO_AUTH_KASUMI_F9
  • RTE_CRYPTO_AUTH_AES_GMAC
  • RTE_CRYPTO_AUTH_ZUC_EIA3
  • RTE_CRYPTO_AUTH_AES_CMAC

Supported AEAD algorithms:

  • RTE_CRYPTO_AEAD_AES_GCM
  • RTE_CRYPTO_AEAD_AES_CCM
  • RTE_CRYPTO_AEAD_CHACHA20_POLY1305

Protocol offloads:

  • RTE_SECURITY_PROTOCOL_DOCSIS

18.1.2. Supported Chains

All the usual chains are supported and also some mixed chains:

Table 18.1 Supported hash-cipher chains for wireless digest-encrypted cases
Cipher algorithm NULL AUTH SNOW3G UIA2 ZUC EIA3 AES CMAC
NULL CIPHER Y 2&3 2&3 Y
SNOW3G UEA2 2&3 Y 2&3 2&3
ZUC EEA3 2&3 2&3 2&3 2&3
AES CTR Y 2&3 2&3 Y
  • The combinations marked as “Y” are supported on all QAT hardware versions.
  • The combinations marked as “2&3” are supported on GEN2/GEN3 QAT hardware only.

18.1.3. Limitations

  • Only supports the session-oriented API implementation (session-less APIs are not supported).
  • SNOW 3G (UEA2), KASUMI (F8) and ZUC (EEA3) supported only if cipher length and offset fields are byte-multiple.
  • SNOW 3G (UIA2) and ZUC (EIA3) supported only if hash length and offset fields are byte-multiple.
  • No BSD support as BSD QAT kernel driver not available.
  • ZUC EEA3/EIA3 is not supported by dh895xcc devices
  • Maximum additional authenticated data (AAD) for GCM is 240 bytes long and must be passed to the device in a buffer rounded up to the nearest block-size multiple (x16) and padded with zeros.
  • Queue-pairs are thread-safe on Intel CPUs but Queues are not (that is, within a single queue-pair all enqueues to the TX queue must be done from one thread and all dequeues from the RX queue must be done from one thread, but enqueues and dequeues may be done in different threads.)
  • A GCM limitation exists, but only in the case where there are multiple generations of QAT devices on a single platform. To optimise performance, the GCM crypto session should be initialised for the device generation to which the ops will be enqueued. Specifically if a GCM session is initialised on a GEN2 device, but then attached to an op enqueued to a GEN3 device, it will work but cannot take advantage of hardware optimisations in the GEN3 device. And if a GCM session is initialised on a GEN3 device, then attached to an op sent to a GEN1/GEN2 device, it will not be enqueued to the device and will be marked as failed. The simplest way to mitigate this is to use the bdf whitelist to avoid mixing devices of different generations in the same process if planning to use for GCM.
  • The mixed algo feature on GEN2 is not supported by all kernel drivers. Check the notes under the Available Kernel Drivers table below for specific details.
  • Out-of-place is not supported for combined Crypto-CRC DOCSIS security protocol.
  • RTE_CRYPTO_CIPHER_DES_DOCSISBPI is not supported for combined Crypto-CRC DOCSIS security protocol.
  • Multi-segment buffers are not supported for combined Crypto-CRC DOCSIS security protocol.

18.1.4. Extra notes on KASUMI F9

When using KASUMI F9 authentication algorithm, the input buffer must be constructed according to the 3GPP KASUMI specification (section 4.4, page 13). The input buffer has to have COUNT (4 bytes), FRESH (4 bytes), MESSAGE and DIRECTION (1 bit) concatenated. After the DIRECTION bit, a single ‘1’ bit is appended, followed by between 0 and 7 ‘0’ bits, so that the total length of the buffer is multiple of 8 bits. Note that the actual message can be any length, specified in bits.

Once this buffer is passed this way, when creating the crypto operation, length of data to authenticate “op.sym.auth.data.length” must be the length of all the items described above, including the padding at the end. Also, offset of data to authenticate “op.sym.auth.data.offset” must be such that points at the start of the COUNT bytes.

18.2. Asymmetric Crypto Service on QAT

The QAT asymmetric crypto PMD (hereafter referred to as QAT ASYM [PMD]) provides poll mode crypto driver support for the following hardware accelerator devices:

  • Intel QuickAssist Technology DH895xCC
  • Intel QuickAssist Technology C62x
  • Intel QuickAssist Technology C3xxx
  • Intel QuickAssist Technology D15xx
  • Intel QuickAssist Technology C4xxx

The QAT ASYM PMD has support for:

  • RTE_CRYPTO_ASYM_XFORM_MODEX
  • RTE_CRYPTO_ASYM_XFORM_MODINV

18.2.1. Limitations

  • Big integers longer than 4096 bits are not supported.
  • Queue-pairs are thread-safe on Intel CPUs but Queues are not (that is, within a single queue-pair all enqueues to the TX queue must be done from one thread and all dequeues from the RX queue must be done from one thread, but enqueues and dequeues may be done in different threads.)
  • RSA-2560, RSA-3584 are not supported

18.3. Building PMDs on QAT

A QAT device can host multiple acceleration services:

  • symmetric cryptography
  • data compression
  • asymmetric cryptography

These services are provided to DPDK applications via PMDs which register to implement the corresponding cryptodev and compressdev APIs. The PMDs use common QAT driver code which manages the QAT PCI device. They also depend on a QAT kernel driver being installed on the platform, see Dependency on the QAT kernel driver below.

18.3.1. Configuring and Building the DPDK QAT PMDs

Further information on configuring, building and installing DPDK is described here.

Quick instructions for QAT cryptodev PMD are as follows:

cd to the top-level DPDK directory
make defconfig
sed -i 's,\(CONFIG_RTE_LIBRTE_PMD_QAT_SYM\)=n,\1=y,' build/.config
or/and
sed -i 's,\(CONFIG_RTE_LIBRTE_PMD_QAT_ASYM\)=n,\1=y,' build/.config
make

Quick instructions for QAT compressdev PMD are as follows:

cd to the top-level DPDK directory
make defconfig
make

18.3.2. Build Configuration

These are the build configuration options affecting QAT, and their default values:

CONFIG_RTE_LIBRTE_PMD_QAT=y
CONFIG_RTE_LIBRTE_PMD_QAT_SYM=n
CONFIG_RTE_LIBRTE_PMD_QAT_ASYM=n
CONFIG_RTE_PMD_QAT_MAX_PCI_DEVICES=48
CONFIG_RTE_PMD_QAT_COMP_IM_BUFFER_SIZE=65536

CONFIG_RTE_LIBRTE_PMD_QAT must be enabled for any QAT PMD to be built.

Both QAT SYM PMD and QAT ASYM PMD have an external dependency on libcrypto, so are not built by default. CONFIG_RTE_LIBRTE_PMD_QAT_SYM/ASYM should be enabled to build them.

The QAT compressdev PMD has no external dependencies, so needs no configuration options and is built by default.

The number of VFs per PF varies - see table below. If multiple QAT packages are installed on a platform then CONFIG_RTE_PMD_QAT_MAX_PCI_DEVICES should be adjusted to the number of VFs which the QAT common code will need to handle.

Note

There are separate config items (not QAT-specific) for max cryptodevs CONFIG_RTE_CRYPTO_MAX_DEVS and max compressdevs CONFIG_RTE_COMPRESS_MAX_DEVS, if necessary these should be adjusted to handle the total of QAT and other devices which the process will use. In particular for crypto, where each QAT VF may expose two crypto devices, sym and asym, it may happen that the number of devices will be bigger than MAX_DEVS and the process will show an error during PMD initialisation. To avoid this problem CONFIG_RTE_CRYPTO_MAX_DEVS may be increased or -w, pci-whitelist domain:bus:devid:func option may be used.

QAT compression PMD needs intermediate buffers to support Deflate compression with Dynamic Huffman encoding. CONFIG_RTE_PMD_QAT_COMP_IM_BUFFER_SIZE specifies the size of a single buffer, the PMD will allocate a multiple of these, plus some extra space for associated meta-data. For GEN2 devices, 20 buffers are allocated while for GEN1 devices, 12 buffers are allocated, plus 1472 bytes overhead.

Note

If the compressed output of a Deflate operation using Dynamic Huffman Encoding is too big to fit in an intermediate buffer, then the operation will be split into smaller operations and their results will be merged afterwards. This is not possible if any checksum calculation was requested - in such case the code falls back to fixed compression. To avoid this less performant case, applications should configure the intermediate buffer size to be larger than the expected input data size (compressed output size is usually unknown, so the only option is to make larger than the input size).

18.3.3. Running QAT PMD with minimum threshold for burst size

If only a small number or packets can be enqueued. Each enqueue causes an expensive MMIO write. These MMIO write occurrences can be optimised by setting any of the following parameters:

  • qat_sym_enq_threshold
  • qat_asym_enq_threshold
  • qat_comp_enq_threshold

When any of these parameters is set rte_cryptodev_enqueue_burst function will return 0 (thereby avoiding an MMIO) if the device is congested and number of packets possible to enqueue is smaller. To use this feature the user must set the parameter on process start as a device additional parameter:

-w 03:01.1,qat_sym_enq_threshold=32,qat_comp_enq_threshold=16

All parameters can be used with the same device regardless of order. Parameters are separated by comma. When the same parameter is used more than once first occurrence of the parameter is used. Maximum threshold that can be set is 32.

18.3.4. Device and driver naming

  • The qat cryptodev symmetric crypto driver name is “crypto_qat”.
  • The qat cryptodev asymmetric crypto driver name is “crypto_qat_asym”.

The “rte_cryptodev_devices_get()” returns the devices exposed by either of these drivers.

  • Each qat sym crypto device has a unique name, in format “<pci bdf>_<service>”, e.g. “0000:41:01.0_qat_sym”.
  • Each qat asym crypto device has a unique name, in format “<pci bdf>_<service>”, e.g. “0000:41:01.0_qat_asym”. This name can be passed to “rte_cryptodev_get_dev_id()” to get the device_id.

Note

The cryptodev driver name is passed to the dpdk-test-crypto-perf tool in the “-devtype” parameter.

The qat crypto device name is in the format of the slave parameter passed to the crypto scheduler.

  • The qat compressdev driver name is “compress_qat”. The rte_compressdev_devices_get() returns the devices exposed by this driver.
  • Each qat compression device has a unique name, in format <pci bdf>_<service>, e.g. “0000:41:01.0_qat_comp”. This name can be passed to rte_compressdev_get_dev_id() to get the device_id.

18.3.5. Dependency on the QAT kernel driver

To use QAT an SRIOV-enabled QAT kernel driver is required. The VF devices created and initialised by this driver will be used by the QAT PMDs.

Instructions for installation are below, but first an explanation of the relationships between the PF/VF devices and the PMDs visible to DPDK applications.

Each QuickAssist PF device exposes a number of VF devices. Each VF device can enable one symmetric cryptodev PMD and/or one asymmetric cryptodev PMD and/or one compressdev PMD. These QAT PMDs share the same underlying device and pci-mgmt code, but are enumerated independently on their respective APIs and appear as independent devices to applications.

Note

Each VF can only be used by one DPDK process. It is not possible to share the same VF across multiple processes, even if these processes are using different acceleration services.

Conversely one DPDK process can use one or more QAT VFs and can expose both cryptodev and compressdev instances on each of those VFs.

18.3.6. Available kernel drivers

Kernel drivers for each device for each service are listed in the following table. (Scroll right to see the full table)

Table 18.2 QAT device generations, devices and drivers
S A C Gen Device Driver/ver Kernel Module Pci Driver PF Did #PFs VF Did VFs/PF
Yes No No 1 DH895xCC linux/4.4+ qat_dh895xcc dh895xcc 435 1 443 32
Yes Yes No “ “ 01.org/4.2.0+ “ “ “ “ “ “
Yes Yes Yes “ “ 01.org/4.3.0+ “ “ “ “ “ “
Yes No No 2 C62x linux/4.5+ qat_c62x c6xx 37c8 3 37c9 16
Yes Yes Yes “ “ 01.org/4.2.0+ “ “ “ “ “ “
Yes No No 2 C3xxx linux/4.5+ qat_c3xxx c3xxx 19e2 1 19e3 16
Yes Yes Yes “ “ 01.org/4.2.0+ “ “ “ “ “ “
Yes No No 2 200xx p qat_200xx 200xx 18ee 1 18ef 16
Yes No No 2 D15xx 01.org/4.2.0+ qat_d15xx d15xx 6f54 1 6f55 16
Yes No No 3 C4xxx p qat_c4xxx c4xxx 18a0 1 18a1 128
  • Note: Symmetric mixed crypto algorithms feature on Gen 2 works only with 01.org driver version 4.9.0+

The first 3 columns indicate the service:

  • S = Symmetric crypto service (via cryptodev API)
  • A = Asymmetric crypto service (via cryptodev API)
  • C = Compression service (via compressdev API)

The Driver column indicates either the Linux kernel version in which support for this device was introduced or a driver available on Intel’s 01.org website. There are both linux in-tree and 01.org kernel drivers available for some devices. p = release pending.

If you are running on a kernel which includes a driver for your device, see Installation using kernel.org driver below. Otherwise see Installation using 01.org QAT driver.

18.3.7. Installation using kernel.org driver

The examples below are based on the C62x device, if you have a different device use the corresponding values in the above table.

In BIOS ensure that SRIOV is enabled and either:

  • Disable VT-d or
  • Enable VT-d and set "intel_iommu=on iommu=pt" in the grub file.

Check that the QAT driver is loaded on your system, by executing:

lsmod | grep qa

You should see the kernel module for your device listed, e.g.:

qat_c62x               5626  0
intel_qat              82336  1 qat_c62x

Next, you need to expose the Virtual Functions (VFs) using the sysfs file system.

First find the BDFs (Bus-Device-Function) of the physical functions (PFs) of your device, e.g.:

lspci -d:37c8

You should see output similar to:

1a:00.0 Co-processor: Intel Corporation Device 37c8
3d:00.0 Co-processor: Intel Corporation Device 37c8
3f:00.0 Co-processor: Intel Corporation Device 37c8

Enable the VFs for each PF by echoing the number of VFs per PF to the pci driver:

echo 16 > /sys/bus/pci/drivers/c6xx/0000:1a:00.0/sriov_numvfs
echo 16 > /sys/bus/pci/drivers/c6xx/0000:3d:00.0/sriov_numvfs
echo 16 > /sys/bus/pci/drivers/c6xx/0000:3f:00.0/sriov_numvfs

Check that the VFs are available for use. For example lspci -d:37c9 should list 48 VF devices available for a C62x device.

To complete the installation follow the instructions in Binding the available VFs to the DPDK UIO driver.

Note

If the QAT kernel modules are not loaded and you see an error like Failed to load MMP firmware qat_895xcc_mmp.bin in kernel logs, this may be as a result of not using a distribution, but just updating the kernel directly.

Download firmware from the kernel firmware repo.

Copy qat binaries to /lib/firmware:

cp qat_895xcc.bin /lib/firmware
cp qat_895xcc_mmp.bin /lib/firmware

Change to your linux source root directory and start the qat kernel modules:

insmod ./drivers/crypto/qat/qat_common/intel_qat.ko
insmod ./drivers/crypto/qat/qat_dh895xcc/qat_dh895xcc.ko

Note

If you see the following warning in /var/log/messages it can be ignored: IOMMU should be enabled for SR-IOV to work correctly.

18.3.8. Installation using 01.org QAT driver

Download the latest QuickAssist Technology Driver from 01.org. Consult the Getting Started Guide at the same URL for further information.

The steps below assume you are:

  • Building on a platform with one C62x device.
  • Using package qat1.7.l.4.2.0-000xx.tar.gz.
  • On Fedora26 kernel 4.11.11-300.fc26.x86_64.

In the BIOS ensure that SRIOV is enabled and VT-d is disabled.

Uninstall any existing QAT driver, for example by running:

  • ./installer.sh uninstall in the directory where originally installed.

Build and install the SRIOV-enabled QAT driver:

mkdir /QAT
cd /QAT

# Copy the package to this location and unpack
tar zxof qat1.7.l.4.2.0-000xx.tar.gz

./configure --enable-icp-sriov=host
make install

You can use cat /sys/kernel/debug/qat<your device type and bdf>/version/fw to confirm the driver is correctly installed and is using firmware version 4.2.0. You can use lspci -d:37c9 to confirm the presence of the 16 VF devices available per C62x PF.

Confirm the driver is correctly installed and is using firmware version 4.2.0:

cat /sys/kernel/debug/qat<your device type and bdf>/version/fw

Confirm the presence of 48 VF devices - 16 per PF:

lspci -d:37c9

To complete the installation - follow instructions in Binding the available VFs to the DPDK UIO driver.

Note

If using a later kernel and the build fails with an error relating to strict_stroul not being available apply the following patch:

/QAT/QAT1.6/quickassist/utilities/downloader/Target_CoreLibs/uclo/include/linux/uclo_platform.h
+ #if LINUX_VERSION_CODE >= KERNEL_VERSION(3,18,5)
+ #define STR_TO_64(str, base, num, endPtr) {endPtr=NULL; if (kstrtoul((str), (base), (num))) printk("Error strtoull convert %s\n", str); }
+ #else
#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,38)
#define STR_TO_64(str, base, num, endPtr) {endPtr=NULL; if (strict_strtoull((str), (base), (num))) printk("Error strtoull convert %s\n", str); }
#else
#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,25)
#define STR_TO_64(str, base, num, endPtr) {endPtr=NULL; strict_strtoll((str), (base), (num));}
#else
#define STR_TO_64(str, base, num, endPtr)                                 \
     do {                                                               \
           if (str[0] == '-')                                           \
           {                                                            \
                *(num) = -(simple_strtoull((str+1), &(endPtr), (base))); \
           }else {                                                      \
                *(num) = simple_strtoull((str), &(endPtr), (base));      \
           }                                                            \
     } while(0)
+ #endif
#endif
#endif

Note

If the build fails due to missing header files you may need to do following:

sudo yum install zlib-devel
sudo yum install openssl-devel
sudo yum install libudev-devel

Note

If the build or install fails due to mismatching kernel sources you may need to do the following:

sudo yum install kernel-headers-`uname -r`
sudo yum install kernel-src-`uname -r`
sudo yum install kernel-devel-`uname -r`

18.3.9. Binding the available VFs to the DPDK UIO driver

Unbind the VFs from the stock driver so they can be bound to the uio driver.

18.3.9.1. For an Intel(R) QuickAssist Technology DH895xCC device

The unbind command below assumes BDFs of 03:01.00-03:04.07, if your VFs are different adjust the unbind command below:

for device in $(seq 1 4); do \
    for fn in $(seq 0 7); do \
        echo -n 0000:03:0${device}.${fn} > \
        /sys/bus/pci/devices/0000\:03\:0${device}.${fn}/driver/unbind; \
    done; \
done

18.3.9.2. For an Intel(R) QuickAssist Technology C62x device

The unbind command below assumes BDFs of 1a:01.00-1a:02.07, 3d:01.00-3d:02.07 and 3f:01.00-3f:02.07, if your VFs are different adjust the unbind command below:

for device in $(seq 1 2); do \
    for fn in $(seq 0 7); do \
        echo -n 0000:1a:0${device}.${fn} > \
        /sys/bus/pci/devices/0000\:1a\:0${device}.${fn}/driver/unbind; \

        echo -n 0000:3d:0${device}.${fn} > \
        /sys/bus/pci/devices/0000\:3d\:0${device}.${fn}/driver/unbind; \

        echo -n 0000:3f:0${device}.${fn} > \
        /sys/bus/pci/devices/0000\:3f\:0${device}.${fn}/driver/unbind; \
    done; \
done

18.3.9.3. For Intel(R) QuickAssist Technology C3xxx or 200xx or D15xx device

The unbind command below assumes BDFs of 01:01.00-01:02.07, if your VFs are different adjust the unbind command below:

for device in $(seq 1 2); do \
    for fn in $(seq 0 7); do \
        echo -n 0000:01:0${device}.${fn} > \
        /sys/bus/pci/devices/0000\:01\:0${device}.${fn}/driver/unbind; \
    done; \
done

18.3.9.4. Bind to the DPDK uio driver

Install the DPDK igb_uio driver, bind the VF PCI Device id to it and use lspci to confirm the VF devices are now in use by igb_uio kernel driver, e.g. for the C62x device:

cd to the top-level DPDK directory
modprobe uio
insmod ./build/kmod/igb_uio.ko
echo "8086 37c9" > /sys/bus/pci/drivers/igb_uio/new_id
lspci -vvd:37c9

Another way to bind the VFs to the DPDK UIO driver is by using the dpdk-devbind.py script:

cd to the top-level DPDK directory
./usertools/dpdk-devbind.py -b igb_uio 0000:03:01.1

18.3.10. Testing

QAT SYM crypto PMD can be tested by running the test application:

make defconfig
make -j
cd ./build/app
./test -l1 -n1 -w <your qat bdf>
RTE>>cryptodev_qat_autotest

QAT ASYM crypto PMD can be tested by running the test application:

make defconfig
make -j
cd ./build/app
./test -l1 -n1 -w <your qat bdf>
RTE>>cryptodev_qat_asym_autotest

QAT compression PMD can be tested by running the test application:

make defconfig
sed -i 's,\(CONFIG_RTE_COMPRESSDEV_TEST\)=n,\1=y,' build/.config
make -j
cd ./build/app
./test -l1 -n1 -w <your qat bdf>
RTE>>compressdev_autotest

18.3.11. Debugging

There are 2 sets of trace available via the dynamic logging feature:

  • pmd.qat_dp exposes trace on the data-path.
  • pmd.qat_general exposes all other trace.

pmd.qat exposes both sets of traces. They can be enabled using the log-level option (where 8=maximum log level) on the process cmdline, e.g. using any of the following:

--log-level="pmd.qat_general,8"
--log-level="pmd.qat_dp,8"
--log-level="pmd.qat,8"

Note

The global RTE_LOG_DP_LEVEL overrides data-path trace so must be set to RTE_LOG_DEBUG to see all the trace. This variable is in config/rte_config.h for meson build and config/common_base for gnu make. Also the dynamic global log level overrides both sets of trace, so e.g. no QAT trace would display in this case:

--log-level="7" --log-level="pmd.qat_general,8"