26. QEDE Poll Mode Driver

26.1. Supported Features

• Unicast/Multicast filtering
• Promiscuous mode
• Allmulti mode
• Port hardware statistics
• Jumbo frames
• Multiple MAC address
• MTU change
• Default pause flow control
• Multiprocess aware
• Scatter-Gather
• Multiple Rx/Tx queues
• RSS (with RETA/hash table/key)
• TSS
• Stateless checksum offloads (IPv4/IPv6/TCP/UDP)
• LRO/TSO
• VLAN offload - Filtering and stripping
• N-tuple filter and flow director (limited support)
• NPAR (NIC Partitioning)
• SR-IOV VF
• VXLAN Tunneling offload
• GENEVE Tunneling offload
• MPLSoUDP Tx Tunneling offload

26.2. Non-supported Features

• SR-IOV PF
• GRE and NVGRE Tunneling offloads

26.3. Co-existence considerations

• QLogic FastLinQ QL4xxxx CNAs can have both NIC and Storage personalities. However, coexistence with storage protocol drivers (qedi and qedf) is not supported on the same adapter. So storage personality has to be disabled on that adapter when used in DPDK applications.
• For SR-IOV case, qede PMD will be used to bind to SR-IOV VF device and Linux native kernel driver (qede) will be attached to SR-IOV PF.

26.4. Supported QLogic Adapters

• QLogic FastLinQ QL4xxxx 10G/25G/40G/50G/100G Intelligent Ethernet Adapters (IEA) and Converged Network Adapters (CNA)

26.5. Prerequisites

• Requires storm firmware version 8.30.12.0. Firmware may be available inbox in certain newer Linux distros under the standard directory E.g. /lib/firmware/qed/qed_init_values-8.30.12.0.bin If the required firmware files are not available then download it from QLogic Driver Download Center. For downloading firmware file, select adapter category, model and DPDK Poll Mode Driver.
• Requires management firmware (MFW) version 8.30.x.x or higher to be flashed on to the adapter. If the required management firmware is not available then download from QLogic Driver Download Center. For downloading firmware upgrade utility, select adapter category, model and Linux distro. To flash the management firmware refer to the instructions in the QLogic Firmware Upgrade Utility Readme document.
• SR-IOV requires Linux PF driver version 8.20.x.x or higher. If the required PF driver is not available then download it from QLogic Driver Download Center. For downloading PF driver, select adapter category, model and Linux distro.

26.6. Driver compilation and testing

Refer to the document compiling and testing a PMD for a NIC for details.

26.7. SR-IOV: Prerequisites and Sample Application Notes

This section provides instructions to configure SR-IOV with Linux OS.

Note: librte_pmd_qede will be used to bind to SR-IOV VF device and Linux native kernel driver (qede) will function as SR-IOV PF driver. Requires PF driver to be 8.10.x.x or higher.

1. Verify SR-IOV and ARI capability is enabled on the adapter using lspci:

   lspci -s <slot> -vvv
   

   Example output:

   [...]
   Capabilities: [1b8 v1] Alternative Routing-ID Interpretation (ARI)
   [...]
   Capabilities: [1c0 v1] Single Root I/O Virtualization (SR-IOV)
   [...]
   Kernel driver in use: igb_uio
   

2. Load the kernel module:

   modprobe qede
   

   Example output:

   systemd-udevd[4848]: renamed network interface eth0 to ens5f0
   systemd-udevd[4848]: renamed network interface eth1 to ens5f1
   

3. Bring up the PF ports:

   ifconfig ens5f0 up
   ifconfig ens5f1 up
   

4. Create VF device(s):

   Echo the number of VFs to be created into "sriov_numvfs" sysfs entry of the parent PF.

   Example output:

   echo 2 > /sys/devices/pci0000:00/0000:00:03.0/0000:81:00.0/sriov_numvfs
   

5. Assign VF MAC address:

   Assign MAC address to the VF using iproute2 utility. The syntax is:

   ip link set <PF iface> vf <VF id> mac <macaddr>
   

   Example output:

   ip link set ens5f0 vf 0 mac 52:54:00:2f:9d:e8
   

6. PCI Passthrough:

   The VF devices may be passed through to the guest VM using virt-manager or virsh. QEDE PMD should be used to bind the VF devices in the guest VM using the instructions from Driver compilation and testing section above.

7. Running testpmd (Supply --log-level="pmd.net.qede.driver",7 to view informational messages):

   Refer to the document compiling and testing a PMD for a NIC to run testpmd application.

   Example output:

     testpmd -l 0,4-11 -n 4 -- -i --nb-cores=8 --portmask=0xf --rxd=4096 \
     --txd=4096 --txfreet=4068 --enable-rx-cksum --rxq=4 --txq=4 \
     --rss-ip --rss-udp
   
     [...]
   
   EAL: PCI device 0000:84:00.0 on NUMA socket 1
   EAL:   probe driver: 1077:1634 rte_qede_pmd
   EAL:   Not managed by a supported kernel driver, skipped
   EAL: PCI device 0000:84:00.1 on NUMA socket 1
   EAL:   probe driver: 1077:1634 rte_qede_pmd
   EAL:   Not managed by a supported kernel driver, skipped
   EAL: PCI device 0000:88:00.0 on NUMA socket 1
   EAL:   probe driver: 1077:1656 rte_qede_pmd
   EAL:   PCI memory mapped at 0x7f738b200000
   EAL:   PCI memory mapped at 0x7f738b280000
   EAL:   PCI memory mapped at 0x7f738b300000
   PMD: Chip details : BB1
   PMD: Driver version : QEDE PMD 8.7.9.0_1.0.0
   PMD: Firmware version : 8.7.7.0
   PMD: Management firmware version : 8.7.8.0
   PMD: Firmware file : /lib/firmware/qed/qed_init_values_zipped-8.7.7.0.bin
   [QEDE PMD: (84:00.0:dpdk-port-0)]qede_common_dev_init:macaddr \
                                                       00:0e:1e:d2:09:9c
     [...]
   [QEDE PMD: (84:00.0:dpdk-port-0)]qede_tx_queue_setup:txq 0 num_desc 4096 \
                                               tx_free_thresh 4068 socket 0
   [QEDE PMD: (84:00.0:dpdk-port-0)]qede_tx_queue_setup:txq 1 num_desc 4096 \
                                               tx_free_thresh 4068 socket 0
   [QEDE PMD: (84:00.0:dpdk-port-0)]qede_tx_queue_setup:txq 2 num_desc 4096 \
                                                tx_free_thresh 4068 socket 0
   [QEDE PMD: (84:00.0:dpdk-port-0)]qede_tx_queue_setup:txq 3 num_desc 4096 \
                                                tx_free_thresh 4068 socket 0
   [QEDE PMD: (84:00.0:dpdk-port-0)]qede_rx_queue_setup:rxq 0 num_desc 4096 \
                                               rx_buf_size=2148 socket 0
   [QEDE PMD: (84:00.0:dpdk-port-0)]qede_rx_queue_setup:rxq 1 num_desc 4096 \
                                               rx_buf_size=2148 socket 0
   [QEDE PMD: (84:00.0:dpdk-port-0)]qede_rx_queue_setup:rxq 2 num_desc 4096 \
                                               rx_buf_size=2148 socket 0
   [QEDE PMD: (84:00.0:dpdk-port-0)]qede_rx_queue_setup:rxq 3 num_desc 4096 \
                                               rx_buf_size=2148 socket 0
   [QEDE PMD: (84:00.0:dpdk-port-0)]qede_dev_start:port 0
   [QEDE PMD: (84:00.0:dpdk-port-0)]qede_dev_start:link status: down
     [...]
   Checking link statuses...
   Port 0 Link Up - speed 25000 Mbps - full-duplex
   Port 1 Link Up - speed 25000 Mbps - full-duplex
   Port 2 Link Up - speed 25000 Mbps - full-duplex
   Port 3 Link Up - speed 25000 Mbps - full-duplex
   Done
   testpmd>