rte_pmd_i40e.h File Reference

#include <rte_compat.h>
#include <rte_ethdev.h>
#include <rte_ether.h>

Go to the source code of this file.

Data Structures
struct	rte_pmd_i40e_mb_event_param
struct	rte_pmd_i40e_ddp_version
struct	rte_pmd_i40e_ddp_device_id
struct	rte_pmd_i40e_profile_info
struct	rte_pmd_i40e_profile_list
struct	rte_pmd_i40e_proto_info
struct	rte_pmd_i40e_ptype_info
struct	rte_pmd_i40e_queue_region_conf
struct	rte_pmd_i40e_pkt_template_action
struct	rte_pmd_i40e_pkt_template_input
struct	rte_pmd_i40e_pkt_template_conf

Macros
#define	RTE_PMD_I40E_PTYPE_USER_DEFINE_MASK   0x80000000

Enumerations
enum	rte_pmd_i40e_mb_event_rsp { RTE_PMD_I40E_MB_EVENT_NOOP_ACK, RTE_PMD_I40E_MB_EVENT_NOOP_NACK, RTE_PMD_I40E_MB_EVENT_PROCEED, RTE_PMD_I40E_MB_EVENT_MAX }
enum	rte_pmd_i40e_package_op { , RTE_PMD_I40E_PKG_OP_WR_ADD, RTE_PMD_I40E_PKG_OP_WR_DEL, RTE_PMD_I40E_PKG_OP_WR_ONLY }
enum	rte_pmd_i40e_package_info
enum	rte_pmd_i40e_queue_region_op { ,   RTE_PMD_I40E_RSS_QUEUE_REGION_SET, RTE_PMD_I40E_RSS_QUEUE_REGION_FLOWTYPE_SET, RTE_PMD_I40E_RSS_QUEUE_REGION_USER_PRIORITY_SET, RTE_PMD_I40E_RSS_QUEUE_REGION_ALL_FLUSH_ON,   RTE_PMD_I40E_RSS_QUEUE_REGION_ALL_FLUSH_OFF }
enum	rte_pmd_i40e_pkt_template_behavior
enum	rte_pmd_i40e_pkt_template_status { RTE_PMD_I40E_PKT_TEMPLATE_NO_REPORT_STATUS, RTE_PMD_I40E_PKT_TEMPLATE_REPORT_ID, RTE_PMD_I40E_PKT_TEMPLATE_REPORT_ID_FLEX_4, RTE_PMD_I40E_PKT_TEMPLATE_REPORT_FLEX_8 }

Functions
int	rte_pmd_i40e_flow_add_del_packet_template (uint16_t port, const struct rte_pmd_i40e_pkt_template_conf *conf, uint8_t add)
int	rte_pmd_i40e_ping_vfs (uint16_t port, uint16_t vf)
int	rte_pmd_i40e_set_vf_mac_anti_spoof (uint16_t port, uint16_t vf_id, uint8_t on)
int	rte_pmd_i40e_set_vf_vlan_anti_spoof (uint16_t port, uint16_t vf_id, uint8_t on)
int	rte_pmd_i40e_set_tx_loopback (uint16_t port, uint8_t on)
int	rte_pmd_i40e_set_vf_unicast_promisc (uint16_t port, uint16_t vf_id, uint8_t on)
int	rte_pmd_i40e_set_vf_multicast_promisc (uint16_t port, uint16_t vf_id, uint8_t on)
int	rte_pmd_i40e_set_vf_mac_addr (uint16_t port, uint16_t vf_id, struct rte_ether_addr *mac_addr)
int	rte_pmd_i40e_remove_vf_mac_addr (uint16_t port, uint16_t vf_id, struct rte_ether_addr *mac_addr)
int	rte_pmd_i40e_set_vf_vlan_stripq (uint16_t port, uint16_t vf, uint8_t on)
int	rte_pmd_i40e_set_vf_vlan_insert (uint16_t port, uint16_t vf_id, uint16_t vlan_id)
int	rte_pmd_i40e_set_vf_broadcast (uint16_t port, uint16_t vf_id, uint8_t on)
int	rte_pmd_i40e_set_vf_vlan_tag (uint16_t port, uint16_t vf_id, uint8_t on)
int	rte_pmd_i40e_set_vf_vlan_filter (uint16_t port, uint16_t vlan_id, uint64_t vf_mask, uint8_t on)
int	rte_pmd_i40e_get_vf_stats (uint16_t port, uint16_t vf_id, struct rte_eth_stats *stats)
int	rte_pmd_i40e_reset_vf_stats (uint16_t port, uint16_t vf_id)
int	rte_pmd_i40e_set_vf_max_bw (uint16_t port, uint16_t vf_id, uint32_t bw)
int	rte_pmd_i40e_set_vf_tc_bw_alloc (uint16_t port, uint16_t vf_id, uint8_t tc_num, uint8_t *bw_weight)
int	rte_pmd_i40e_set_vf_tc_max_bw (uint16_t port, uint16_t vf_id, uint8_t tc_no, uint32_t bw)
int	rte_pmd_i40e_set_tc_strict_prio (uint16_t port, uint8_t tc_map)
int	rte_pmd_i40e_process_ddp_package (uint16_t port, uint8_t *buff, uint32_t size, enum rte_pmd_i40e_package_op op)
int	rte_pmd_i40e_get_ddp_info (uint8_t *pkg, uint32_t pkg_size, uint8_t *info, uint32_t size, enum rte_pmd_i40e_package_info type)
int	rte_pmd_i40e_get_ddp_list (uint16_t port, uint8_t *buff, uint32_t size)
int	rte_pmd_i40e_ptype_mapping_update (uint16_t port, struct rte_pmd_i40e_ptype_mapping *mapping_items, uint16_t count, uint8_t exclusive)
int	rte_pmd_i40e_ptype_mapping_reset (uint16_t port)
int	rte_pmd_i40e_ptype_mapping_get (uint16_t port, struct rte_pmd_i40e_ptype_mapping *mapping_items, uint16_t size, uint16_t *count, uint8_t valid_only)
int	rte_pmd_i40e_ptype_mapping_replace (uint16_t port, uint32_t target, uint8_t mask, uint32_t pkt_type)
int	rte_pmd_i40e_add_vf_mac_addr (uint16_t port, uint16_t vf_id, struct rte_ether_addr *mac_addr)
int	rte_pmd_i40e_flow_type_mapping_update (uint16_t port, struct rte_pmd_i40e_flow_type_mapping *mapping_items, uint16_t count, uint8_t exclusive)
int	rte_pmd_i40e_flow_type_mapping_get (uint16_t port, struct rte_pmd_i40e_flow_type_mapping *mapping_items)
int	rte_pmd_i40e_flow_type_mapping_reset (uint16_t port)
int	rte_pmd_i40e_query_vfid_by_mac (uint16_t port, const struct rte_ether_addr *vf_mac)
int	rte_pmd_i40e_rss_queue_region_conf (uint16_t port_id, enum rte_pmd_i40e_queue_region_op op_type, void *arg)
int	rte_pmd_i40e_inset_get (uint16_t port, uint8_t pctype, struct rte_pmd_i40e_inset *inset, enum rte_pmd_i40e_inset_type inset_type)
int	rte_pmd_i40e_inset_set (uint16_t port, uint8_t pctype, struct rte_pmd_i40e_inset *inset, enum rte_pmd_i40e_inset_type inset_type)
static int	rte_pmd_i40e_inset_field_get (uint64_t inset, uint8_t field_idx)
static int	rte_pmd_i40e_inset_field_set (uint64_t *inset, uint8_t field_idx)
static int	rte_pmd_i40e_inset_field_clear (uint64_t *inset, uint8_t field_idx)
__rte_experimental int	rte_pmd_i40e_get_fdir_info (uint16_t port, struct rte_eth_fdir_info *fdir_info)
__rte_experimental int	rte_pmd_i40e_get_fdir_stats (uint16_t port, struct rte_eth_fdir_stats *fdir_stat)
__rte_experimental int	rte_pmd_i40e_set_gre_key_len (uint16_t port, uint8_t len)
__rte_experimental int	rte_pmd_i40e_set_switch_dev (uint16_t port_id, struct rte_eth_dev *switch_dev)
__rte_experimental int	rte_pmd_i40e_set_pf_src_prune (uint16_t port, uint8_t on)

Detailed Description

i40e PMD specific functions.

EXPERIMENTAL: this API may change, or be removed, without prior notice

Definition in file rte_pmd_i40e.h.

Macro Definition Documentation

RTE_PMD_I40E_PTYPE_USER_DEFINE_MASK

#define RTE_PMD_I40E_PTYPE_USER_DEFINE_MASK   0x80000000

ptype mapping table only accept RTE_PTYPE_XXX or "user defined" ptype. A ptype with MSB set will be regarded as a user defined ptype. Below macro help to create a user defined ptype.

Definition at line 176 of file rte_pmd_i40e.h.

Enumeration Type Documentation

rte_pmd_i40e_mb_event_rsp

enum rte_pmd_i40e_mb_event_rsp

Response sent back to i40e driver from user app after callback

Enumerator
RTE_PMD_I40E_MB_EVENT_NOOP_ACK	skip mbox request and ACK
RTE_PMD_I40E_MB_EVENT_NOOP_NACK	skip mbox request and NACK
RTE_PMD_I40E_MB_EVENT_PROCEED	proceed with mbox request
RTE_PMD_I40E_MB_EVENT_MAX	max value of this enum

Definition at line 28 of file rte_pmd_i40e.h.

rte_pmd_i40e_package_op

enum rte_pmd_i40e_package_op

Option of package processing.

Enumerator
RTE_PMD_I40E_PKG_OP_WR_ADD	load package and add to info list
RTE_PMD_I40E_PKG_OP_WR_DEL	load package and delete from info list
RTE_PMD_I40E_PKG_OP_WR_ONLY	load package without modifying info list

Definition at line 49 of file rte_pmd_i40e.h.

rte_pmd_i40e_package_info

enum rte_pmd_i40e_package_info

Types of package information.

Definition at line 60 of file rte_pmd_i40e.h.

rte_pmd_i40e_queue_region_op

enum rte_pmd_i40e_queue_region_op

Option types of queue region.

Enumerator
RTE_PMD_I40E_RSS_QUEUE_REGION_SET	add queue region set
RTE_PMD_I40E_RSS_QUEUE_REGION_FLOWTYPE_SET	add PF region pctype set
RTE_PMD_I40E_RSS_QUEUE_REGION_USER_PRIORITY_SET	add queue region user priority set
RTE_PMD_I40E_RSS_QUEUE_REGION_ALL_FLUSH_ON	ALL configuration about queue region from up layer at first will only keep in DPDK software stored in driver, only after " FLUSH_ON ", it commit all configuration to HW. Because PMD had to set hardware configuration at a time, so it will record all up layer command at first.
RTE_PMD_I40E_RSS_QUEUE_REGION_ALL_FLUSH_OFF	"FLUSH_OFF " is just clean all configuration about queue region just now, and restore all to DPDK i40e driver default config when start up.

Definition at line 81 of file rte_pmd_i40e.h.

rte_pmd_i40e_pkt_template_behavior

enum rte_pmd_i40e_pkt_template_behavior

Behavior will be taken if raw packet template is matched.

Definition at line 234 of file rte_pmd_i40e.h.

rte_pmd_i40e_pkt_template_status

enum rte_pmd_i40e_pkt_template_status

Flow director report status It defines what will be reported if raw packet template is matched.

Enumerator
RTE_PMD_I40E_PKT_TEMPLATE_NO_REPORT_STATUS	report nothing
RTE_PMD_I40E_PKT_TEMPLATE_REPORT_ID	only report FD ID
RTE_PMD_I40E_PKT_TEMPLATE_REPORT_ID_FLEX_4	report FD ID and 4 flex bytes
RTE_PMD_I40E_PKT_TEMPLATE_REPORT_FLEX_8	report 8 flex bytes

Definition at line 244 of file rte_pmd_i40e.h.

Function Documentation

rte_pmd_i40e_flow_add_del_packet_template()

int rte_pmd_i40e_flow_add_del_packet_template	(	uint16_t	port,
		const struct rte_pmd_i40e_pkt_template_conf *	conf,
		uint8_t	add
	)

Add or remove raw packet template filter to Flow Director.

Parameters

port	The port identifier of the Ethernet device.
conf	Specifies configuration parameters of raw packet template filter.
add	Specifies an action to be taken - add or remove raw packet template filter.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if conf invalid.
• (-ENOTSUP) not supported by firmware.

rte_pmd_i40e_ping_vfs()

int rte_pmd_i40e_ping_vfs	(	uint16_t	port,
		uint16_t	vf
	)

Notify VF when PF link status changes.

Parameters

port	The port identifier of the Ethernet device.
vf	VF id.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if vf invalid.

rte_pmd_i40e_set_vf_mac_anti_spoof()

int rte_pmd_i40e_set_vf_mac_anti_spoof	(	uint16_t	port,
		uint16_t	vf_id,
		uint8_t	on
	)

Enable/Disable VF MAC anti spoofing.

Parameters

port	The port identifier of the Ethernet device.
vf_id	VF on which to set MAC anti spoofing.
on	1 - Enable VFs MAC anti spoofing. 0 - Disable VFs MAC anti spoofing.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if bad parameter.

rte_pmd_i40e_set_vf_vlan_anti_spoof()

int rte_pmd_i40e_set_vf_vlan_anti_spoof	(	uint16_t	port,
		uint16_t	vf_id,
		uint8_t	on
	)

Enable/Disable VF VLAN anti spoofing.

Parameters

port	The port identifier of the Ethernet device.
vf_id	VF on which to set VLAN anti spoofing.
on	1 - Enable VFs VLAN anti spoofing. 0 - Disable VFs VLAN anti spoofing.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if bad parameter.

rte_pmd_i40e_set_tx_loopback()

int rte_pmd_i40e_set_tx_loopback	(	uint16_t	port,
		uint8_t	on
	)

Enable/Disable TX loopback on all the PF and VFs.

Parameters

port	The port identifier of the Ethernet device.
on	1 - Enable TX loopback. 0 - Disable TX loopback.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if bad parameter.

rte_pmd_i40e_set_vf_unicast_promisc()

int rte_pmd_i40e_set_vf_unicast_promisc	(	uint16_t	port,
		uint16_t	vf_id,
		uint8_t	on
	)

Enable/Disable VF unicast promiscuous mode.

Parameters

port	The port identifier of the Ethernet device.
vf_id	VF on which to set.
on	1 - Enable. 0 - Disable.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if bad parameter.

rte_pmd_i40e_set_vf_multicast_promisc()

int rte_pmd_i40e_set_vf_multicast_promisc	(	uint16_t	port,
		uint16_t	vf_id,
		uint8_t	on
	)

Enable/Disable VF multicast promiscuous mode.

Parameters

port	The port identifier of the Ethernet device.
vf_id	VF on which to set.
on	1 - Enable. 0 - Disable.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if bad parameter.

rte_pmd_i40e_set_vf_mac_addr()

int rte_pmd_i40e_set_vf_mac_addr	(	uint16_t	port,
		uint16_t	vf_id,
		struct rte_ether_addr *	mac_addr
	)

Set the VF MAC address.

PF should set MAC address before VF initialized, if PF sets the MAC address after VF initialized, new MAC address won't be effective until VF reinitialize.

This will remove all existing MAC filters.

Parameters

port	The port identifier of the Ethernet device.
vf_id	VF id.
mac_addr	VF MAC address.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if vf or mac_addr is invalid.

Examples:

examples/vm_power_manager/main.c.

rte_pmd_i40e_remove_vf_mac_addr()

int rte_pmd_i40e_remove_vf_mac_addr	(	uint16_t	port,
		uint16_t	vf_id,
		struct rte_ether_addr *	mac_addr
	)

Remove the VF MAC address.

Parameters

port	The port identifier of the Ethernet device.
vf_id	VF id.
mac_addr	VF MAC address.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if vf or mac_addr is invalid.

rte_pmd_i40e_set_vf_vlan_stripq()

int rte_pmd_i40e_set_vf_vlan_stripq	(	uint16_t	port,
		uint16_t	vf,
		uint8_t	on
	)

Enable/Disable vf vlan strip for all queues in a pool

Parameters

port	The port identifier of the Ethernet device.
vf	ID specifying VF.
on	1 - Enable VF's vlan strip on RX queues. 0 - Disable VF's vlan strip on RX queues.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if bad parameter.

rte_pmd_i40e_set_vf_vlan_insert()

int rte_pmd_i40e_set_vf_vlan_insert	(	uint16_t	port,
		uint16_t	vf_id,
		uint16_t	vlan_id
	)

Enable/Disable vf vlan insert

Parameters

port	The port identifier of the Ethernet device.
vf_id	ID specifying VF.
vlan_id	0 - Disable VF's vlan insert. n - Enable; n is inserted as the vlan id.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if bad parameter.

rte_pmd_i40e_set_vf_broadcast()

int rte_pmd_i40e_set_vf_broadcast	(	uint16_t	port,
		uint16_t	vf_id,
		uint8_t	on
	)

Enable/Disable vf broadcast mode

Parameters

port	The port identifier of the Ethernet device.
vf_id	ID specifying VF.
on	0 - Disable broadcast. 1 - Enable broadcast.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if bad parameter.

rte_pmd_i40e_set_vf_vlan_tag()

int rte_pmd_i40e_set_vf_vlan_tag	(	uint16_t	port,
		uint16_t	vf_id,
		uint8_t	on
	)

Enable/Disable vf vlan tag

Parameters

port	The port identifier of the Ethernet device.
vf_id	ID specifying VF.
on	0 - Disable VF's vlan tag. n - Enable VF's vlan tag.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if bad parameter.

rte_pmd_i40e_set_vf_vlan_filter()

int rte_pmd_i40e_set_vf_vlan_filter	(	uint16_t	port,
		uint16_t	vlan_id,
		uint64_t	vf_mask,
		uint8_t	on
	)

Enable/Disable VF VLAN filter

Parameters

port	The port identifier of the Ethernet device.
vlan_id	ID specifying VLAN
vf_mask	Mask to filter VF's
on	0 - Disable VF's VLAN filter. 1 - Enable VF's VLAN filter.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if bad parameter.
• (-ENOTSUP) not supported by firmware.

rte_pmd_i40e_get_vf_stats()

int rte_pmd_i40e_get_vf_stats	(	uint16_t	port,
		uint16_t	vf_id,
		struct rte_eth_stats *	stats
	)

Get VF's statistics

Parameters

port	The port identifier of the Ethernet device.
vf_id	VF on which to get.
stats	A pointer to a structure of type rte_eth_stats to be filled with the values of device counters for the following set of statistics: ipackets with the total of successfully received packets. opackets with the total of successfully transmitted packets. ibytes with the total of successfully received bytes. obytes with the total of successfully transmitted bytes. ierrors with the total of erroneous received packets. oerrors with the total of failed transmitted packets.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if bad parameter.

Examples:

examples/vm_power_manager/channel_monitor.c.

rte_pmd_i40e_reset_vf_stats()

int rte_pmd_i40e_reset_vf_stats	(	uint16_t	port,
		uint16_t	vf_id
	)

Clear VF's statistics

Parameters

port	The port identifier of the Ethernet device.
vf_id	VF on which to get.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if bad parameter.

rte_pmd_i40e_set_vf_max_bw()

int rte_pmd_i40e_set_vf_max_bw	(	uint16_t	port,
		uint16_t	vf_id,
		uint32_t	bw
	)

Set VF's max bandwidth.

Per VF bandwidth limitation and per TC bandwidth limitation cannot be enabled in parallel. If per TC bandwidth is enabled, this function will disable it.

Parameters

port	The port identifier of the Ethernet device.
vf_id	ID specifying VF.
bw	Bandwidth for this VF. The value should be an absolute bandwidth in Mbps. The bandwidth is a L2 bandwidth counting the bytes of ethernet packets. Not count the bytes added by physical layer.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if bad parameter.
• (-ENOTSUP) not supported by firmware.

rte_pmd_i40e_set_vf_tc_bw_alloc()

int rte_pmd_i40e_set_vf_tc_bw_alloc	(	uint16_t	port,
		uint16_t	vf_id,
		uint8_t	tc_num,
		uint8_t *	bw_weight
	)

Set all the TCs' bandwidth weight on a specific VF.

The bw_weight means the percentage occupied by the TC. It can be taken as the relative min bandwidth setting.

Parameters

port	The port identifier of the Ethernet device.
vf_id	ID specifying VF.
tc_num	Number of TCs.
bw_weight	An array of relative bandwidth weight for all the TCs. The summary of the bw_weight should be 100.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if bad parameter.
• (-ENOTSUP) not supported by firmware.

rte_pmd_i40e_set_vf_tc_max_bw()

int rte_pmd_i40e_set_vf_tc_max_bw	(	uint16_t	port,
		uint16_t	vf_id,
		uint8_t	tc_no,
		uint32_t	bw
	)

Set a specific TC's max bandwidth on a specific VF.

Parameters

port	The port identifier of the Ethernet device.
vf_id	ID specifying VF.
tc_no	Number specifying TC.
bw	Max bandwidth for this TC. The value should be an absolute bandwidth in Mbps. The bandwidth is a L2 bandwidth counting the bytes of ethernet packets. Not count the bytes added by physical layer.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if bad parameter.
• (-ENOTSUP) not supported by firmware.

rte_pmd_i40e_set_tc_strict_prio()

int rte_pmd_i40e_set_tc_strict_prio	(	uint16_t	port,
		uint8_t	tc_map
	)

Set some TCs to strict priority mode on a physical port.

Parameters

port	The port identifier of the Ethernet device.
tc_map	A bit map for the TCs.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if bad parameter.
• (-ENOTSUP) not supported by firmware.

rte_pmd_i40e_process_ddp_package()

int rte_pmd_i40e_process_ddp_package	(	uint16_t	port,
		uint8_t *	buff,
		uint32_t	size,
		enum rte_pmd_i40e_package_op	op
	)

Load/Unload a ddp package

Parameters

port	The port identifier of the Ethernet device.
buff	buffer of package.
size	size of buffer.
op	Operation of package processing

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if bad parameter.
• (-EEXIST) if profile exists.
• (-EACCES) if profile does not exist.
• (-ENOTSUP) if operation not supported.

rte_pmd_i40e_get_ddp_info()

int rte_pmd_i40e_get_ddp_info	(	uint8_t *	pkg,
		uint32_t	pkg_size,
		uint8_t *	info,
		uint32_t	size,
		enum rte_pmd_i40e_package_info	type
	)

rte_pmd_i40e_get_ddp_info - Get profile's info

Parameters

pkg	buffer of package.
pkg_size	package buffer size
info	buffer for response
size	response buffer size
type	type of information requested

Returns

• (0) if successful.
• (-ENOTSUP) if information type not supported by the profile.
• (-EINVAL) if bad parameter.

rte_pmd_i40e_get_ddp_list()

int rte_pmd_i40e_get_ddp_list	(	uint16_t	port,
		uint8_t *	buff,
		uint32_t	size
	)

rte_pmd_i40e_get_ddp_list - Get loaded profile list

Parameters

port	port id
buff	buffer for response
size	buffer size

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if bad parameter.

rte_pmd_i40e_ptype_mapping_update()

int rte_pmd_i40e_ptype_mapping_update	(	uint16_t	port,
		struct rte_pmd_i40e_ptype_mapping *	mapping_items,
		uint16_t	count,
		uint8_t	exclusive
	)

Update hardware defined ptype to software defined packet type mapping table.

Parameters

port	pointer to port identifier of the device.
mapping_items	the base address of the mapping items array.
count	number of mapping items.
exclusive	the flag indicate different ptype mapping update method. -(0) only overwrite referred PTYPE mapping, keep other PTYPEs mapping unchanged. -(!0) overwrite referred PTYPE mapping, set other PTYPEs maps to PTYPE_UNKNOWN.

rte_pmd_i40e_ptype_mapping_reset()

int rte_pmd_i40e_ptype_mapping_reset

(

uint16_t

port

)

Reset hardware defined ptype to software defined ptype mapping table to default.

Parameters

port	pointer to port identifier of the device

rte_pmd_i40e_ptype_mapping_get()

int rte_pmd_i40e_ptype_mapping_get	(	uint16_t	port,
		struct rte_pmd_i40e_ptype_mapping *	mapping_items,
		uint16_t	size,
		uint16_t *	count,
		uint8_t	valid_only
	)

Get hardware defined ptype to software defined ptype mapping items.

Parameters

port	pointer to port identifier of the device.
mapping_items	the base address of the array to store returned items.
size	the size of the input array.
count	the place to store the number of returned items.
valid_only	-(0) return full mapping table. -(!0) only return mapping items which packet_type != RTE_PTYPE_UNKNOWN.

rte_pmd_i40e_ptype_mapping_replace()

int rte_pmd_i40e_ptype_mapping_replace	(	uint16_t	port,
		uint32_t	target,
		uint8_t	mask,
		uint32_t	pkt_type
	)

Replace a specific or a group of software defined ptypes with a new one

Parameters

port	pointer to port identifier of the device
target	the packet type to be replaced
mask	-(0) target represent a specific software defined ptype. -(!0) target is a mask to represent a group of software defined ptypes.
pkt_type	the new packet type to overwrite

rte_pmd_i40e_add_vf_mac_addr()

int rte_pmd_i40e_add_vf_mac_addr	(	uint16_t	port,
		uint16_t	vf_id,
		struct rte_ether_addr *	mac_addr
	)

Add a VF MAC address.

Add more MAC address for VF. The existing MAC addresses are still effective.

Parameters

port	The port identifier of the Ethernet device.
vf_id	VF id.
mac_addr	VF MAC address.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if vf or mac_addr is invalid.

rte_pmd_i40e_flow_type_mapping_update()

int rte_pmd_i40e_flow_type_mapping_update	(	uint16_t	port,
		struct rte_pmd_i40e_flow_type_mapping *	mapping_items,
		uint16_t	count,
		uint8_t	exclusive
	)

Update hardware defined pctype to software defined flow type mapping table.

Parameters

port	pointer to port identifier of the device.
mapping_items	the base address of the mapping items array.
count	number of mapping items.
exclusive	the flag indicate different pctype mapping update method. -(0) only overwrite referred PCTYPE mapping, keep other PCTYPEs mapping unchanged. -(!0) overwrite referred PCTYPE mapping, set other PCTYPEs maps to PCTYPE_INVALID.

rte_pmd_i40e_flow_type_mapping_get()

int rte_pmd_i40e_flow_type_mapping_get	(	uint16_t	port,
		struct rte_pmd_i40e_flow_type_mapping *	mapping_items
	)

Get software defined flow type to hardware defined pctype mapping items.

Parameters

port	pointer to port identifier of the device.
mapping_items	the base address of the array to store returned items. array should be allocated by caller with minimum size of RTE_PMD_I40E_FLOW_TYPE_MAX items

rte_pmd_i40e_flow_type_mapping_reset()

int rte_pmd_i40e_flow_type_mapping_reset

(

uint16_t

port

)

Reset hardware defined pctype to software defined flow type mapping table to default.

Parameters

port	pointer to port identifier of the device

rte_pmd_i40e_query_vfid_by_mac()

int rte_pmd_i40e_query_vfid_by_mac	(	uint16_t	port,
		const struct rte_ether_addr *	vf_mac
	)

On the PF, find VF index based on VF MAC address

Parameters

port	pointer to port identifier of the device
vf_mac	the mac address of the vf to determine index of

Returns

The index of vfid If successful. -EINVAL: vf mac address does not exist for this port -ENOTSUP: i40e not supported for this port.

Examples:

examples/vm_power_manager/channel_monitor.c.

rte_pmd_i40e_rss_queue_region_conf()

int rte_pmd_i40e_rss_queue_region_conf	(	uint16_t	port_id,
		enum rte_pmd_i40e_queue_region_op	op_type,
		void *	arg
	)

Do RSS queue region configuration for that port as the command option type

Parameters

port_id	The port identifier of the Ethernet device.
op_type	Queue region operation type
arg	Queue region operation type specific data

rte_pmd_i40e_inset_get()

int rte_pmd_i40e_inset_get	(	uint16_t	port,
		uint8_t	pctype,
		struct rte_pmd_i40e_inset *	inset,
		enum rte_pmd_i40e_inset_type	inset_type
	)

Get input set

Parameters

port	The port identifier of the Ethernet device.
pctype	HW pctype.
inset	Buffer for input set info.
inset_type	Type of input set.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if bad parameter.
• (-ENOTSUP) if operation not supported.

rte_pmd_i40e_inset_set()

int rte_pmd_i40e_inset_set	(	uint16_t	port,
		uint8_t	pctype,
		struct rte_pmd_i40e_inset *	inset,
		enum rte_pmd_i40e_inset_type	inset_type
	)

Set input set

Parameters

port	The port identifier of the Ethernet device.
pctype	HW pctype.
inset	Input set info.
inset_type	Type of input set.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if bad parameter.
• (-ENOTSUP) if operation not supported.

rte_pmd_i40e_inset_field_get()

static int rte_pmd_i40e_inset_field_get ( uint64_t  inset, uint8_t  field_idx  )

inlinestatic

Get bit value for some field index

Parameters

inset	Input set value.
field_idx	Field index for input set.

Returns

• (1) if set.
• (0) if cleared.

Definition at line 1006 of file rte_pmd_i40e.h.

rte_pmd_i40e_inset_field_set()

static int rte_pmd_i40e_inset_field_set ( uint64_t *  inset, uint8_t  field_idx  )

inlinestatic

Set bit value for some field index

Parameters

inset	Input set value.
field_idx	Field index for input set.

Returns

• (-1) if failed.
• (0) if success.

Definition at line 1032 of file rte_pmd_i40e.h.

rte_pmd_i40e_inset_field_clear()

static int rte_pmd_i40e_inset_field_clear ( uint64_t *  inset, uint8_t  field_idx  )

inlinestatic

Clear bit value for some field index

Parameters

inset	Input set value.
field_idx	Field index for input set.

Returns

• (-1) if failed.
• (0) if success.

Definition at line 1057 of file rte_pmd_i40e.h.

rte_pmd_i40e_get_fdir_info()

__rte_experimental int rte_pmd_i40e_get_fdir_info	(	uint16_t	port,
		struct rte_eth_fdir_info *	fdir_info
	)

Get port fdir info

Parameters

port	The port identifier of the Ethernet device.
fdir_info	The fdir info of the port

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-ENOTSUP) if operation not supported.

rte_pmd_i40e_get_fdir_stats()

__rte_experimental int rte_pmd_i40e_get_fdir_stats	(	uint16_t	port,
		struct rte_eth_fdir_stats *	fdir_stat
	)

Get port fdir status

Parameters

port	The port identifier of the Ethernet device.
fdir_stat	The fdir status of the port

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-ENOTSUP) if operation not supported.

rte_pmd_i40e_set_gre_key_len()

__rte_experimental int rte_pmd_i40e_set_gre_key_len	(	uint16_t	port,
		uint8_t	len
	)

Set GRE key length

Parameters

port	The port identifier of the Ethernet device.
len	Length of gre-key

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-ENOTSUP) if operation not supported.

rte_pmd_i40e_set_switch_dev()

__rte_experimental int rte_pmd_i40e_set_switch_dev	(	uint16_t	port_id,
		struct rte_eth_dev *	switch_dev
	)

For ipn3ke, i40e works with FPGA. In this situation, i40e get link status from fpga, fpga works as switch_dev for i40e. This function set switch_dev for i40e.

Parameters

port_id	port_id of i40e device to be set switch device.
switch_dev	target switch device from which i40e device to get link status from.

Returns

• (less than 0) if failed.
• (0) if success.

rte_pmd_i40e_set_pf_src_prune()

__rte_experimental int rte_pmd_i40e_set_pf_src_prune	(	uint16_t	port,
		uint8_t	on
	)

Enable/Disable source prune on all the PF.

Parameters

port	The port identifier of the Ethernet device.
on	1 - Enable source prune. 0 - Disable source prune.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if bad parameter.