rte_pmd_ixgbe.h File Reference

#include <rte_compat.h>
#include <rte_ethdev.h>
#include <rte_ether.h>

Go to the source code of this file.

Data Structures
struct	rte_pmd_ixgbe_mb_event_param

Enumerations
enum	rte_pmd_ixgbe_mb_event_rsp { RTE_PMD_IXGBE_MB_EVENT_NOOP_ACK , RTE_PMD_IXGBE_MB_EVENT_NOOP_NACK , RTE_PMD_IXGBE_MB_EVENT_PROCEED , RTE_PMD_IXGBE_MB_EVENT_MAX }

Functions
int	rte_pmd_ixgbe_ping_vf (uint16_t port, uint16_t vf)
int	rte_pmd_ixgbe_set_vf_mac_addr (uint16_t port, uint16_t vf, struct rte_ether_addr *mac_addr)
int	rte_pmd_ixgbe_set_vf_vlan_anti_spoof (uint16_t port, uint16_t vf, uint8_t on)
int	rte_pmd_ixgbe_set_vf_mac_anti_spoof (uint16_t port, uint16_t vf, uint8_t on)
int	rte_pmd_ixgbe_set_vf_vlan_insert (uint16_t port, uint16_t vf, uint16_t vlan_id)
int	rte_pmd_ixgbe_set_tx_loopback (uint16_t port, uint8_t on)
int	rte_pmd_ixgbe_set_all_queues_drop_en (uint16_t port, uint8_t on)
int	rte_pmd_ixgbe_set_vf_split_drop_en (uint16_t port, uint16_t vf, uint8_t on)
int	rte_pmd_ixgbe_set_vf_vlan_stripq (uint16_t port, uint16_t vf, uint8_t on)
int	rte_pmd_ixgbe_macsec_enable (uint16_t port, uint8_t en, uint8_t rp)
int	rte_pmd_ixgbe_macsec_disable (uint16_t port)
int	rte_pmd_ixgbe_macsec_config_txsc (uint16_t port, uint8_t *mac)
int	rte_pmd_ixgbe_macsec_config_rxsc (uint16_t port, uint8_t *mac, uint16_t pi)
int	rte_pmd_ixgbe_macsec_select_txsa (uint16_t port, uint8_t idx, uint8_t an, uint32_t pn, uint8_t *key)
int	rte_pmd_ixgbe_macsec_select_rxsa (uint16_t port, uint8_t idx, uint8_t an, uint32_t pn, uint8_t *key)
int	rte_pmd_ixgbe_set_vf_rxmode (uint16_t port, uint16_t vf, uint16_t rx_mask, uint8_t on)
int	rte_pmd_ixgbe_set_vf_rx (uint16_t port, uint16_t vf, uint8_t on)
int	rte_pmd_ixgbe_set_vf_tx (uint16_t port, uint16_t vf, uint8_t on)
int	rte_pmd_ixgbe_set_vf_vlan_filter (uint16_t port, uint16_t vlan, uint64_t vf_mask, uint8_t vlan_on)
int	rte_pmd_ixgbe_set_vf_rate_limit (uint16_t port, uint16_t vf, uint16_t tx_rate, uint64_t q_msk)
int	rte_pmd_ixgbe_set_tc_bw_alloc (uint16_t port, uint8_t tc_num, uint8_t *bw_weight)
int	rte_pmd_ixgbe_bypass_init (uint16_t port)
int	rte_pmd_ixgbe_bypass_state_show (uint16_t port, uint32_t *state)
int	rte_pmd_ixgbe_bypass_state_set (uint16_t port, uint32_t *new_state)
int	rte_pmd_ixgbe_bypass_event_show (uint16_t port, uint32_t event, uint32_t *state)
int	rte_pmd_ixgbe_bypass_event_store (uint16_t port, uint32_t event, uint32_t state)
int	rte_pmd_ixgbe_bypass_wd_timeout_store (uint16_t port, uint32_t timeout)
int	rte_pmd_ixgbe_bypass_ver_show (uint16_t port, uint32_t *ver)
int	rte_pmd_ixgbe_bypass_wd_timeout_show (uint16_t port, uint32_t *wd_timeout)
int	rte_pmd_ixgbe_bypass_wd_reset (uint16_t port)
__rte_experimental int	rte_pmd_ixgbe_mdio_lock (uint16_t port)
__rte_experimental int	rte_pmd_ixgbe_mdio_unlock (uint16_t port)
__rte_experimental int	rte_pmd_ixgbe_mdio_unlocked_read (uint16_t port, uint32_t reg_addr, uint32_t dev_type, uint16_t *phy_data)
__rte_experimental int	rte_pmd_ixgbe_mdio_unlocked_write (uint16_t port, uint32_t reg_addr, uint32_t dev_type, uint16_t phy_data)
__rte_experimental int	rte_pmd_ixgbe_upd_fctrl_sbp (uint16_t port, int enable)
__rte_experimental int	rte_pmd_ixgbe_get_fdir_info (uint16_t port, struct rte_eth_fdir_info *fdir_info)
__rte_experimental int	rte_pmd_ixgbe_get_fdir_stats (uint16_t port, struct rte_eth_fdir_stats *fdir_stats)

Detailed Description

ixgbe PMD specific functions.

Definition in file rte_pmd_ixgbe.h.

Enumeration Type Documentation

rte_pmd_ixgbe_mb_event_rsp

enum rte_pmd_ixgbe_mb_event_rsp

Response sent back to ixgbe driver from user app after callback

Enumerator
RTE_PMD_IXGBE_MB_EVENT_NOOP_ACK	skip mbox request and ACK
RTE_PMD_IXGBE_MB_EVENT_NOOP_NACK	skip mbox request and NACK
RTE_PMD_IXGBE_MB_EVENT_PROCEED	proceed with mbox request
RTE_PMD_IXGBE_MB_EVENT_MAX	max value of this enum

Definition at line 657 of file rte_pmd_ixgbe.h.

Function Documentation

rte_pmd_ixgbe_ping_vf()

int rte_pmd_ixgbe_ping_vf	(	uint16_t	port,
		uint16_t	vf
	)

Notify VF when PF link status changes.

Parameters

port	The port identifier of the Ethernet device.
vf	VF id.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if vf invalid.

rte_pmd_ixgbe_set_vf_mac_addr()

int rte_pmd_ixgbe_set_vf_mac_addr	(	uint16_t	port,
		uint16_t	vf,
		struct rte_ether_addr *	mac_addr
	)

Set the VF MAC address.

Parameters

port	The port identifier of the Ethernet device.
vf	VF id.
mac_addr	VF MAC address.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if vf or mac_addr is invalid.

Examples

examples/vm_power_manager/main.c.

rte_pmd_ixgbe_set_vf_vlan_anti_spoof()

int rte_pmd_ixgbe_set_vf_vlan_anti_spoof	(	uint16_t	port,
		uint16_t	vf,
		uint8_t	on
	)

Enable/Disable VF VLAN anti spoofing.

Parameters

port	The port identifier of the Ethernet device.
vf	VF on which to set VLAN anti spoofing.
on	1 - Enable VFs VLAN anti spoofing. 0 - Disable VFs VLAN anti spoofing.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if bad parameter.

rte_pmd_ixgbe_set_vf_mac_anti_spoof()

int rte_pmd_ixgbe_set_vf_mac_anti_spoof	(	uint16_t	port,
		uint16_t	vf,
		uint8_t	on
	)

Enable/Disable VF MAC anti spoofing.

Parameters

port	The port identifier of the Ethernet device.
vf	VF on which to set MAC anti spoofing.
on	1 - Enable VFs MAC anti spoofing. 0 - Disable VFs MAC anti spoofing.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if bad parameter.

rte_pmd_ixgbe_set_vf_vlan_insert()

int rte_pmd_ixgbe_set_vf_vlan_insert	(	uint16_t	port,
		uint16_t	vf,
		uint16_t	vlan_id
	)

Enable/Disable vf vlan insert

Parameters

port	The port identifier of the Ethernet device.
vf	ID specifying VF.
vlan_id	0 - Disable VF's vlan insert. n - Enable; n is inserted as the vlan id.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if bad parameter.

rte_pmd_ixgbe_set_tx_loopback()

int rte_pmd_ixgbe_set_tx_loopback	(	uint16_t	port,
		uint8_t	on
	)

Enable/Disable tx loopback

Parameters

port	The port identifier of the Ethernet device.
on	1 - Enable tx loopback. 0 - Disable tx loopback.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if bad parameter.

rte_pmd_ixgbe_set_all_queues_drop_en()

int rte_pmd_ixgbe_set_all_queues_drop_en	(	uint16_t	port,
		uint8_t	on
	)

set all queues drop enable bit

Parameters

port	The port identifier of the Ethernet device.
on	1 - set the queue drop enable bit for all pools. 0 - reset the queue drop enable bit for all pools.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if bad parameter.

rte_pmd_ixgbe_set_vf_split_drop_en()

int rte_pmd_ixgbe_set_vf_split_drop_en	(	uint16_t	port,
		uint16_t	vf,
		uint8_t	on
	)

set drop enable bit in the VF split rx control register

Parameters

port	The port identifier of the Ethernet device.
vf	ID specifying VF.
on	1 - set the drop enable bit in the split rx control register. 0 - reset the drop enable bit in the split rx control register.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if bad parameter.

rte_pmd_ixgbe_set_vf_vlan_stripq()

int rte_pmd_ixgbe_set_vf_vlan_stripq	(	uint16_t	port,
		uint16_t	vf,
		uint8_t	on
	)

Enable/Disable vf vlan strip for all queues in a pool

Parameters

port	The port identifier of the Ethernet device.
vf	ID specifying VF.
on	1 - Enable VF's vlan strip on RX queues. 0 - Disable VF's vlan strip on RX queues.

Returns

• (0) if successful.
• (-ENOTSUP) if hardware doesn't support this feature.
• (-ENODEV) if port invalid.
• (-EINVAL) if bad parameter.

rte_pmd_ixgbe_macsec_enable()

int rte_pmd_ixgbe_macsec_enable	(	uint16_t	port,
		uint8_t	en,
		uint8_t	rp
	)

Enable MACsec offload.

Parameters

port	The port identifier of the Ethernet device.
en	1 - Enable encryption (encrypt and add integrity signature). 0 - Disable encryption (only add integrity signature).
rp	1 - Enable replay protection. 0 - Disable replay protection.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-ENOTSUP) if hardware doesn't support this feature.

rte_pmd_ixgbe_macsec_disable()

int rte_pmd_ixgbe_macsec_disable

(

uint16_t

port

)

Disable MACsec offload.

Parameters

port	The port identifier of the Ethernet device.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-ENOTSUP) if hardware doesn't support this feature.

rte_pmd_ixgbe_macsec_config_txsc()

int rte_pmd_ixgbe_macsec_config_txsc	(	uint16_t	port,
		uint8_t *	mac
	)

Configure Tx SC (Secure Connection).

Parameters

port	The port identifier of the Ethernet device.
mac	The MAC address on the local side.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-ENOTSUP) if hardware doesn't support this feature.

rte_pmd_ixgbe_macsec_config_rxsc()

int rte_pmd_ixgbe_macsec_config_rxsc	(	uint16_t	port,
		uint8_t *	mac,
		uint16_t	pi
	)

Configure Rx SC (Secure Connection).

Parameters

port	The port identifier of the Ethernet device.
mac	The MAC address on the remote side.
pi	The PI (port identifier) on the remote side.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-ENOTSUP) if hardware doesn't support this feature.

rte_pmd_ixgbe_macsec_select_txsa()

int rte_pmd_ixgbe_macsec_select_txsa	(	uint16_t	port,
		uint8_t	idx,
		uint8_t	an,
		uint32_t	pn,
		uint8_t *	key
	)

Enable Tx SA (Secure Association).

Parameters

port	The port identifier of the Ethernet device.
idx	The SA to be enabled (0 or 1).
an	The association number on the local side.
pn	The packet number on the local side.
key	The key on the local side.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-ENOTSUP) if hardware doesn't support this feature.
• (-EINVAL) if bad parameter.

rte_pmd_ixgbe_macsec_select_rxsa()

int rte_pmd_ixgbe_macsec_select_rxsa	(	uint16_t	port,
		uint8_t	idx,
		uint8_t	an,
		uint32_t	pn,
		uint8_t *	key
	)

Enable Rx SA (Secure Association).

Parameters

port	The port identifier of the Ethernet device.
idx	The SA to be enabled (0 or 1)
an	The association number on the remote side.
pn	The packet number on the remote side.
key	The key on the remote side.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-ENOTSUP) if hardware doesn't support this feature.
• (-EINVAL) if bad parameter.

rte_pmd_ixgbe_set_vf_rxmode()

int rte_pmd_ixgbe_set_vf_rxmode	(	uint16_t	port,
		uint16_t	vf,
		uint16_t	rx_mask,
		uint8_t	on
	)

Set RX L2 Filtering mode of a VF of an Ethernet device.

Parameters

port	The port identifier of the Ethernet device.
vf	VF id.
rx_mask	The RX mode mask, which is one or more of accepting Untagged Packets, packets that match the PFUTA table, Broadcast and Multicast Promiscuous. RTE_ETH_VMDQ_ACCEPT_UNTAG, RTE_ETH_VMDQ_ACCEPT_HASH_UC, RTE_ETH_VMDQ_ACCEPT_BROADCAST and RTE_ETH_VMDQ_ACCEPT_MULTICAST will be used in rx_mode.
on	1 - Enable a VF RX mode. 0 - Disable a VF RX mode.

Returns

• (0) if successful.
• (-ENOTSUP) if hardware doesn't support.
• (-ENODEV) if port_id invalid.
• (-EINVAL) if bad parameter.

Examples

examples/ethtool/lib/rte_ethtool.c.

rte_pmd_ixgbe_set_vf_rx()

int rte_pmd_ixgbe_set_vf_rx	(	uint16_t	port,
		uint16_t	vf,
		uint8_t	on
	)

Enable or disable a VF traffic receive of an Ethernet device.

Parameters

port	The port identifier of the Ethernet device.
vf	VF id.
on	1 - Enable a VF traffic receive. 0 - Disable a VF traffic receive.

Returns

• (0) if successful.
• (-ENOTSUP) if hardware doesn't support.
• (-ENODEV) if port_id invalid.
• (-EINVAL) if bad parameter.

rte_pmd_ixgbe_set_vf_tx()

int rte_pmd_ixgbe_set_vf_tx	(	uint16_t	port,
		uint16_t	vf,
		uint8_t	on
	)

Enable or disable a VF traffic transmit of the Ethernet device.

Parameters

port	The port identifier of the Ethernet device.
vf	VF id.
on	1 - Enable a VF traffic transmit. 0 - Disable a VF traffic transmit.

Returns

• (0) if successful.
• (-ENODEV) if port_id invalid.
• (-ENOTSUP) if hardware doesn't support.
• (-EINVAL) if bad parameter.

rte_pmd_ixgbe_set_vf_vlan_filter()

int rte_pmd_ixgbe_set_vf_vlan_filter	(	uint16_t	port,
		uint16_t	vlan,
		uint64_t	vf_mask,
		uint8_t	vlan_on
	)

Enable/Disable hardware VF VLAN filtering by an Ethernet device of received VLAN packets tagged with a given VLAN Tag Identifier.

Parameters

port	The port identifier of the Ethernet device.
vlan	The VLAN Tag Identifier whose filtering must be enabled or disabled.
vf_mask	Bitmap listing which VFs participate in the VLAN filtering.
vlan_on	1 - Enable VFs VLAN filtering. 0 - Disable VFs VLAN filtering.

Returns

• (0) if successful.
• (-ENOTSUP) if hardware doesn't support.
• (-ENODEV) if port_id invalid.
• (-EINVAL) if bad parameter.

rte_pmd_ixgbe_set_vf_rate_limit()

int rte_pmd_ixgbe_set_vf_rate_limit	(	uint16_t	port,
		uint16_t	vf,
		uint16_t	tx_rate,
		uint64_t	q_msk
	)

Set the rate limitation for a vf on an Ethernet device.

Parameters

port	The port identifier of the Ethernet device.
vf	VF id.
tx_rate	The tx rate allocated from the total link speed for this VF id.
q_msk	The queue mask which need to set the rate.

Returns

• (0) if successful.
• (-ENOTSUP) if hardware doesn't support this feature.
• (-ENODEV) if port_id invalid.
• (-EINVAL) if bad parameter.

rte_pmd_ixgbe_set_tc_bw_alloc()

int rte_pmd_ixgbe_set_tc_bw_alloc	(	uint16_t	port,
		uint8_t	tc_num,
		uint8_t *	bw_weight
	)

Set all the TCs' bandwidth weight.

The bw_weight means the percentage occupied by the TC. It can be taken as the relative min bandwidth setting.

Parameters

port	The port identifier of the Ethernet device.
tc_num	Number of TCs.
bw_weight	An array of relative bandwidth weight for all the TCs. The summary of the bw_weight should be 100.

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-EINVAL) if bad parameter.
• (-ENOTSUP) not supported by firmware.

rte_pmd_ixgbe_bypass_init()

int rte_pmd_ixgbe_bypass_init

(

uint16_t

port

)

Initialize bypass logic. This function needs to be called before executing any other bypass API.

Parameters

port	The port identifier of the Ethernet device.

Returns

• (0) if successful.
• (-ENOTSUP) if hardware doesn't support.
• (-EINVAL) if bad parameter.

rte_pmd_ixgbe_bypass_state_show()

int rte_pmd_ixgbe_bypass_state_show	(	uint16_t	port,
		uint32_t *	state
	)

Return bypass state.

Parameters

port	The port identifier of the Ethernet device.
state	The return bypass state. (1) Normal mode (2) Bypass mode (3) Isolate mode

Returns

• (0) if successful.
• (-ENOTSUP) if hardware doesn't support.
• (-EINVAL) if bad parameter.

rte_pmd_ixgbe_bypass_state_set()

int rte_pmd_ixgbe_bypass_state_set	(	uint16_t	port,
		uint32_t *	new_state
	)

Set bypass state

Parameters

port	The port identifier of the Ethernet device.
new_state	The current bypass state. (1) Normal mode (2) Bypass mode (3) Isolate mode

Returns

• (0) if successful.
• (-ENOTSUP) if hardware doesn't support.
• (-EINVAL) if bad parameter.

rte_pmd_ixgbe_bypass_event_show()

int rte_pmd_ixgbe_bypass_event_show	(	uint16_t	port,
		uint32_t	event,
		uint32_t *	state
	)

Return bypass state when given event occurs.

Parameters

port	The port identifier of the Ethernet device.
event	The bypass event (1) Main power on (power button is pushed) (2) Auxiliary power on (power supply is being plugged) (3) Main power off (system shutdown and power supply is left plugged in) (4) Auxiliary power off (power supply is being unplugged) (5) Display or set the watchdog timer
state	The bypass state when given event occurred. (1) Normal mode (2) Bypass mode (3) Isolate mode

Returns

• (0) if successful.
• (-ENOTSUP) if hardware doesn't support.
• (-EINVAL) if bad parameter.

rte_pmd_ixgbe_bypass_event_store()

int rte_pmd_ixgbe_bypass_event_store	(	uint16_t	port,
		uint32_t	event,
		uint32_t	state
	)

Set bypass state when given event occurs.

Parameters

port	The port identifier of the Ethernet device.
event	The bypass event (1) Main power on (power button is pushed) (2) Auxiliary power on (power supply is being plugged) (3) Main power off (system shutdown and power supply is left plugged in) (4) Auxiliary power off (power supply is being unplugged) (5) Display or set the watchdog timer
state	The assigned state when given event occurs. (1) Normal mode (2) Bypass mode (3) Isolate mode

Returns

• (0) if successful.
• (-ENOTSUP) if hardware doesn't support.
• (-EINVAL) if bad parameter.

rte_pmd_ixgbe_bypass_wd_timeout_store()

int rte_pmd_ixgbe_bypass_wd_timeout_store	(	uint16_t	port,
		uint32_t	timeout
	)

Set bypass watchdog timeout count.

Parameters

port	The port identifier of the Ethernet device.
timeout	The timeout to be set. (0) 0 seconds (timer is off) (1) 1.5 seconds (2) 2 seconds (3) 3 seconds (4) 4 seconds (5) 8 seconds (6) 16 seconds (7) 32 seconds

Returns

• (0) if successful.
• (-ENOTSUP) if hardware doesn't support.
• (-EINVAL) if bad parameter.

rte_pmd_ixgbe_bypass_ver_show()

int rte_pmd_ixgbe_bypass_ver_show	(	uint16_t	port,
		uint32_t *	ver
	)

Get bypass firmware version.

Parameters

port	The port identifier of the Ethernet device.
ver	The firmware version

Returns

• (0) if successful.
• (-ENOTSUP) if hardware doesn't support.
• (-EINVAL) if bad parameter.

rte_pmd_ixgbe_bypass_wd_timeout_show()

int rte_pmd_ixgbe_bypass_wd_timeout_show	(	uint16_t	port,
		uint32_t *	wd_timeout
	)

Return bypass watchdog timeout in seconds

Parameters

port	The port identifier of the Ethernet device.
wd_timeout	The return watchdog timeout. "0" represents timer expired (0) 0 seconds (timer is off) (1) 1.5 seconds (2) 2 seconds (3) 3 seconds (4) 4 seconds (5) 8 seconds (6) 16 seconds (7) 32 seconds

Returns

• (0) if successful.
• (-ENOTSUP) if hardware doesn't support.
• (-EINVAL) if bad parameter.

rte_pmd_ixgbe_bypass_wd_reset()

int rte_pmd_ixgbe_bypass_wd_reset

(

uint16_t

port

)

Reset bypass watchdog timer

Parameters

port	The port identifier of the Ethernet device.

Returns

• (0) if successful.
• (-ENOTSUP) if hardware doesn't support.
• (-EINVAL) if bad parameter.

rte_pmd_ixgbe_mdio_lock()

__rte_experimental int rte_pmd_ixgbe_mdio_lock

(

uint16_t

port

)

Acquire swfw semaphore lock for MDIO access

Parameters

port	The port identifier of the Ethernet device.

Returns

• (0) if successful.
• (-ENOTSUP) if hardware doesn't support.
• (-ENODEV) if port invalid.
• (IXGBE_ERR_SWFW_SYNC) If sw/fw semaphore acquisition failed

rte_pmd_ixgbe_mdio_unlock()

__rte_experimental int rte_pmd_ixgbe_mdio_unlock

(

uint16_t

port

)

Release swfw semaphore lock used for MDIO access

Parameters

port	The port identifier of the Ethernet device.

Returns

• (0) if successful.
• (-ENOTSUP) if hardware doesn't support.
• (-ENODEV) if port invalid.

rte_pmd_ixgbe_mdio_unlocked_read()

__rte_experimental int rte_pmd_ixgbe_mdio_unlocked_read	(	uint16_t	port,
		uint32_t	reg_addr,
		uint32_t	dev_type,
		uint16_t *	phy_data
	)

Read PHY register using MDIO without MDIO lock The lock must be taken separately before calling this API

Parameters

port	The port identifier of the Ethernet device.
reg_addr	32 bit PHY Register
dev_type	Used to define device base address
phy_data	Pointer for reading PHY register data

Returns

• (0) if successful.
• (-ENOTSUP) if hardware doesn't support.
• (-ENODEV) if port invalid.
• (IXGBE_ERR_PHY) If PHY read command failed

rte_pmd_ixgbe_mdio_unlocked_write()

__rte_experimental int rte_pmd_ixgbe_mdio_unlocked_write	(	uint16_t	port,
		uint32_t	reg_addr,
		uint32_t	dev_type,
		uint16_t	phy_data
	)

Write data to PHY register using without MDIO lock The lock must be taken separately before calling this API

Parameters

port	The port identifier of the Ethernet device.
reg_addr	32 bit PHY Register
dev_type	Used to define device base address
phy_data	Data to write to PHY register

Returns

• (0) if successful.
• (-ENOTSUP) if hardware doesn't support.
• (-ENODEV) if port invalid.
• (IXGBE_ERR_PHY) If PHY read command failed

rte_pmd_ixgbe_upd_fctrl_sbp()

__rte_experimental int rte_pmd_ixgbe_upd_fctrl_sbp	(	uint16_t	port,
		int	enable
	)

Parameters

port	The port identifier of the Ethernet device.
enable	0 to disable and nonzero to enable 'SBP' bit in FCTRL register to receive all packets

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-ENOTSUP) if hardware doesn't support this feature.

rte_pmd_ixgbe_get_fdir_info()

__rte_experimental int rte_pmd_ixgbe_get_fdir_info	(	uint16_t	port,
		struct rte_eth_fdir_info *	fdir_info
	)

Get port fdir info

Parameters

port	The port identifier of the Ethernet device.
fdir_info	The fdir info of the port

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-ENOTSUP) if operation not supported.

rte_pmd_ixgbe_get_fdir_stats()

__rte_experimental int rte_pmd_ixgbe_get_fdir_stats	(	uint16_t	port,
		struct rte_eth_fdir_stats *	fdir_stats
	)

Get port fdir status

Parameters

port	The port identifier of the Ethernet device.
fdir_stats	The fdir status of the port

Returns

• (0) if successful.
• (-ENODEV) if port invalid.
• (-ENOTSUP) if operation not supported.