|
DPDK
18.11.11
|
#include <rte_comp.h>
Data Fields | |
| struct rte_mempool * | mempool |
| rte_iova_t | iova_addr |
| struct rte_mbuf * | m_src |
| struct rte_mbuf * | m_dst |
| enum rte_comp_flush_flag | flush_flag |
| uint64_t | input_chksum |
| uint64_t | output_chksum |
| uint32_t | consumed |
| uint32_t | produced |
| uint64_t | debug_status |
| uint8_t | status |
| void * | private_xform |
| void * | stream |
| uint32_t | offset |
| uint32_t | length |
| uint8_t * | digest |
Compression Operation.
This structure contains data relating to performing a compression operation on the referenced mbuf data buffers.
Comp operations are enqueued and dequeued in comp PMDs using the rte_compressdev_enqueue_burst() / rte_compressdev_dequeue_burst() APIs
Definition at line 287 of file rte_comp.h.
| void* private_xform |
Stateless private PMD data derived from an rte_comp_xform. A handle returned by rte_compressdev_private_xform_create() must be attached to operations of op_type RTE_COMP_STATELESS.
Definition at line 290 of file rte_comp.h.
| void* stream |
Private PMD data derived initially from an rte_comp_xform, which holds state and history data and evolves as operations are processed. rte_compressdev_stream_create() must be called on a device for all STATEFUL data streams and the resulting stream attached to the one or more operations associated with the data stream. All operations in a stream must be sent to the same device.
Definition at line 295 of file rte_comp.h.
| struct rte_mempool* mempool |
Pool from which operation is allocated
Definition at line 306 of file rte_comp.h.
| rte_iova_t iova_addr |
| struct rte_mbuf* m_src |
source mbuf The total size of the input buffer(s) can be retrieved using rte_pktmbuf_pkt_len(m_src). The max data size which can fit in a single mbuf is limited by the uint16_t rte_mbuf.data_len to 64k-1. If the input data is bigger than this it can be passed to the PMD in a chain of mbufs if the PMD's capabilities indicate it supports this.
Definition at line 310 of file rte_comp.h.
| struct rte_mbuf* m_dst |
destination mbuf The total size of the output buffer(s) can be retrieved using rte_pktmbuf_pkt_len(m_dst). The max data size which can fit in a single mbuf is limited by the uint16_t rte_mbuf.data_len to 64k-1. If the output data is expected to be bigger than this a chain of mbufs can be passed to the PMD if the PMD's capabilities indicate it supports this.
Definition at line 318 of file rte_comp.h.
| uint32_t offset |
Starting point for compression or decompression, specified as number of bytes from start of packet in source buffer. This offset starts from the first segment of the buffer, in case the m_src is a chain of mbufs. Starting point for checksum generation in compress direction.
Starting point for writing output data, specified as number of bytes from start of packet in dest buffer. This offset starts from the first segment of the buffer, in case the m_dst is a chain of mbufs. Starting point for checksum generation in decompress direction.
Definition at line 329 of file rte_comp.h.
| uint32_t length |
The length, in bytes, of the data in source buffer to be compressed or decompressed. Also the length of the data over which the checksum should be generated in compress direction
Definition at line 337 of file rte_comp.h.
| uint8_t* digest |
Output buffer to store hash output, if enabled in xform. Buffer would contain valid value only after an op with flush flag = RTE_COMP_FLUSH_FULL/FLUSH_FINAL is processed successfully.
Length of buffer should be contiguous and large enough to accommodate digest produced by specific hash algo.
Definition at line 356 of file rte_comp.h.
| enum rte_comp_flush_flag flush_flag |
Defines flush characteristics for the output data. Only applicable in compress direction
Definition at line 368 of file rte_comp.h.
| uint64_t input_chksum |
An input checksum can be provided to generate a cumulative checksum across sequential blocks in a STATELESS stream. Checksum type is as specified in xform chksum_type
Definition at line 372 of file rte_comp.h.
| uint64_t output_chksum |
If a checksum is generated it will be written in here. Checksum type is as specified in xform chksum_type.
Definition at line 377 of file rte_comp.h.
| uint32_t consumed |
The number of bytes from the source buffer which were compressed/decompressed.
Definition at line 381 of file rte_comp.h.
| uint32_t produced |
The number of bytes written to the destination buffer which were compressed/decompressed.
Definition at line 385 of file rte_comp.h.
| uint64_t debug_status |
Status of the operation is returned in the status param. This field allows the PMD to pass back extra pmd-specific debug information. Value is not defined on the API.
Definition at line 389 of file rte_comp.h.
| uint8_t status |
Operation status - use values from enum rte_comp_status. This is reset to RTE_COMP_OP_STATUS_NOT_PROCESSED on allocation from mempool and will be set to RTE_COMP_OP_STATUS_SUCCESS after operation is successfully processed by a PMD
Definition at line 395 of file rte_comp.h.
1.8.9.1