7. VF daemon (VFd)
VFd (the VF daemon) is a mechanism which can be used to configure features on a VF (SR-IOV Virtual Function) without direct access to the PF (SR-IOV Physical Function). VFd is an EXPERIMENTAL feature which can only be used in the scenario of DPDK PF with a DPDK VF. If the PF port is driven by the Linux kernel driver then the VFd feature will not work. Currently VFd is only supported by the ixgbe and i40e drivers.
In general VF features cannot be configured directly by an end user application since they are under the control of the PF. The normal approach to configuring a feature on a VF is that an application would call the APIs provided by the VF driver. If the required feature cannot be configured by the VF directly (the most common case) the VF sends a message to the PF through the mailbox on ixgbe and i40e. This means that the availability of the feature depends on whether the appropriate mailbox messages are defined.
DPDK leverages the mailbox interface defined by the Linux kernel driver so that compatibility with the kernel driver can be guaranteed. The downside of this approach is that the availability of messages supported by the kernel become a limitation when the user wants to configure features on the VF.
VFd is a new method of controlling the features on a VF. The VF driver doesn’t talk directly to the PF driver when configuring a feature on the VF. When a VF application (i.e., an application using the VF ports) wants to enable a VF feature, it can send a message to the PF application (i.e., the application using the PF port, which can be the same as the VF application). The PF application will configure the feature for the VF. Obviously, the PF application can also configure the VF features without a request from the VF application.
Compared with the traditional approach the VFd moves the negotiation between VF and PF from the driver level to application level. So the application should define how the negotiation between the VF and PF works, or even if the control should be limited to the PF.
It is the application’s responsibility to use VFd. Consider for example a KVM migration, the VF application may transfer from one VM to another. It is recommended in this case that the PF control the VF features without participation from the VF. Then the VF application has no capability to configure the features. So the user doesn’t need to define the interface between the VF application and the PF application. The service provider should take the control of all the features.
The following sections describe the VFd functionality.
Note
Although VFd is supported by both ixgbe and i40e, please be aware that since the hardware capability is different, the functions supported by ixgbe and i40e are not the same.
7.1. Preparing
VFd only can be used in the scenario of DPDK PF + DPDK VF. Users should bind
the PF port to igb_uio
, then create the VFs based on the DPDK PF host.
The typical procedure to achieve this is as follows:
Boot the system without iommu, or with
iommu=pt
.Bind the PF port to
igb_uio
, for example:dpdk-devbind.py -b igb_uio 01:00.0
Create a Virtual Function:
echo 1 > /sys/bus/pci/devices/0000:01:00.0/max_vfs
Start a VM with the new VF port bypassed to it.
Run a DPDK application on the PF in the host:
dpdk-testpmd -l 0-7 -n 4 -- -i --txqflags=0
Bind the VF port to
igb_uio
in the VM:dpdk-devbind.py -b igb_uio 03:00.0
Run a DPDK application on the VF in the VM:
dpdk-testpmd -l 0-7 -n 4 -- -i --txqflags=0
7.2. Common functions of IXGBE and I40E
The following sections show how to enable PF/VF functionality based on the above testpmd setup.
7.2.1. TX loopback
Run a testpmd runtime command on the PF to set TX loopback:
set tx loopback 0 on|off
This sets whether the PF port and all the VF ports that belong to it are allowed to send the packets to other virtual ports.
Although it is a VFd function, it is the global setting for the whole physical port. When using this function, the PF and all the VFs TX loopback will be enabled/disabled.
7.2.2. VF MAC address setting
Run a testpmd runtime command on the PF to set the MAC address for a VF port:
set vf mac addr 0 0 A0:36:9F:7B:C3:51
This testpmd runtime command will change the MAC address of the VF port to this new address. If any other addresses are set before, they will be overwritten.
7.2.3. VF MAC anti-spoofing
Run a testpmd runtime command on the PF to enable/disable the MAC anti-spoofing for a VF port:
set vf mac antispoof 0 0 on|off
When enabling the MAC anti-spoofing, the port will not forward packets whose source MAC address is not the same as the port.
7.2.4. VF VLAN anti-spoofing
Run a testpmd runtime command on the PF to enable/disable the VLAN anti-spoofing for a VF port:
set vf vlan antispoof 0 0 on|off
When enabling the VLAN anti-spoofing, the port will not send packets whose VLAN ID does not belong to VLAN IDs that this port can receive.
7.2.5. VF VLAN insertion
Run a testpmd runtime command on the PF to set the VLAN insertion for a VF port:
set vf vlan insert 0 0 1
When using this testpmd runtime command, an assigned VLAN ID can be inserted to the transmitted packets by the hardware.
The assigned VLAN ID can be 0. It means disabling the VLAN insertion.
7.2.6. VF VLAN stripping
Run a testpmd runtime command on the PF to enable/disable the VLAN stripping for a VF port:
set vf vlan stripq 0 0 on|off
This testpmd runtime command is used to enable/disable the RX VLAN stripping for a specific VF port.
7.2.7. VF VLAN filtering
Run a testpmd runtime command on the PF to set the VLAN filtering for a VF port:
rx_vlan add 1 port 0 vf 1
rx_vlan rm 1 port 0 vf 1
These two testpmd runtime commands can be used to add or remove the VLAN filter for several VF ports. When the VLAN filters are added only the packets that have the assigned VLAN IDs can be received. Other packets will be dropped by hardware.
7.3. The IXGBE specific VFd functions
The functions in this section are specific to the ixgbe driver.
7.3.1. All queues drop
Run a testpmd runtime command on the PF to enable/disable the all queues drop:
set all queues drop on|off
This is a global setting for the PF and all the VF ports of the physical port.
Enabling the all queues drop
feature means that when there is no available
descriptor for the received packets they are dropped. The all queues drop
feature should be enabled in SR-IOV mode to avoid one queue blocking others.
7.3.2. VF packet drop
Run a testpmd runtime command on the PF to enable/disable the packet drop for a specific VF:
set vf split drop 0 0 on|off
This is a similar function as all queues drop
. The difference is that this
function is per VF setting and the previous function is a global setting.
7.3.3. VF rate limit
Run a testpmd runtime command on the PF to all queues’ rate limit for a specific VF:
set port 0 vf 0 rate 10 queue_mask 1
This is a function to set the rate limit for all the queues in the
queue_mask
bitmap. It is not used to set the summary of the rate
limit. The rate limit of every queue will be set equally to the assigned rate
limit.
7.3.4. VF RX enabling
Run a testpmd runtime command on the PF to enable/disable packet receiving for a specific VF:
set port 0 vf 0 rx on|off
This function can be used to stop/start packet receiving on a VF.
7.3.5. VF TX enabling
Run a testpmd runtime command on the PF to enable/disable packet transmitting for a specific VF:
set port 0 vf 0 tx on|off
This function can be used to stop/start packet transmitting on a VF.
7.3.6. VF RX mode setting
Run a testpmd runtime command on the PF to set the RX mode for a specific VF:
set port 0 vf 0 rxmode AUPE|ROPE|BAM|MPE on|off
This function can be used to enable/disable some RX modes on the VF, including:
- If it accept untagged packets.
- If it accepts packets matching the MAC filters.
- If it accept MAC broadcast packets,
- If it enables MAC multicast promiscuous mode.
7.4. The I40E specific VFd functions
The functions in this section are specific to the i40e driver.
7.4.1. VF statistics
This provides an API to get the a specific VF’s statistic from PF.
7.4.2. VF statistics resetting
This provides an API to rest the a specific VF’s statistic from PF.
7.4.3. VF link status change notification
This provide an API to let a specific VF know if the physical link status changed.
Normally if a VF received this notification, the driver should notify the application to reset the VF port.
7.4.4. VF MAC broadcast setting
Run a testpmd runtime command on the PF to enable/disable MAC broadcast packet receiving for a specific VF:
set vf broadcast 0 0 on|off
7.4.5. VF MAC multicast promiscuous mode
Run a testpmd runtime command on the PF to enable/disable MAC multicast promiscuous mode for a specific VF:
set vf allmulti 0 0 on|off
7.4.6. VF MAC unicast promiscuous mode
Run a testpmd runtime command on the PF to enable/disable MAC unicast promiscuous mode for a specific VF:
set vf promisc 0 0 on|off
7.4.7. VF max bandwidth
Run a testpmd runtime command on the PF to set the TX maximum bandwidth for a specific VF:
set vf tx max-bandwidth 0 0 2000
The maximum bandwidth is an absolute value in Mbps.
7.4.8. VF TC bandwidth allocation
Run a testpmd runtime command on the PF to set the TCs (traffic class) TX bandwidth allocation for a specific VF:
set vf tc tx min-bandwidth 0 0 (20,20,20,40)
The allocated bandwidth should be set for all the TCs. The allocated bandwidth is a relative value as a percentage. The sum of all the bandwidth should be 100.
7.4.9. VF TC max bandwidth
Run a testpmd runtime command on the PF to set the TCs TX maximum bandwidth for a specific VF:
set vf tc tx max-bandwidth 0 0 0 10000
The maximum bandwidth is an absolute value in Mbps.
7.4.10. TC strict priority scheduling
Run a testpmd runtime command on the PF to enable/disable several TCs TX strict priority scheduling:
set tx strict-link-priority 0 0x3
The 0 in the TC bitmap means disabling the strict priority scheduling for this TC. To enable use a value of 1.