rte_pmd_bphy.h File Reference

#include <stdint.h>
#include <rte_common.h>
#include <rte_dev.h>
#include <rte_malloc.h>
#include <rte_memcpy.h>
#include <rte_rawdev.h>

Go to the source code of this file.

Typedefs
typedef void(*	cnxk_bphy_intr_handler_t) (int irq_num, void *isr_data)

Enumerations
enum	cnxk_bphy_cgx_msg_type {   CNXK_BPHY_CGX_MSG_TYPE_GET_LINKINFO , CNXK_BPHY_CGX_MSG_TYPE_INTLBK_DISABLE , CNXK_BPHY_CGX_MSG_TYPE_INTLBK_ENABLE , CNXK_BPHY_CGX_MSG_TYPE_PTP_RX_DISABLE ,   CNXK_BPHY_CGX_MSG_TYPE_PTP_RX_ENABLE , CNXK_BPHY_CGX_MSG_TYPE_SET_LINK_MODE , CNXK_BPHY_CGX_MSG_TYPE_SET_LINK_STATE , CNXK_BPHY_CGX_MSG_TYPE_START_RXTX ,   CNXK_BPHY_CGX_MSG_TYPE_STOP_RXTX , CNXK_BPHY_CGX_MSG_TYPE_GET_SUPPORTED_FEC , CNXK_BPHY_CGX_MSG_TYPE_SET_FEC , CNXK_BPHY_CGX_MSG_TYPE_CPRI_MODE_CHANGE ,   CNXK_BPHY_CGX_MSG_TYPE_CPRI_TX_CONTROL , CNXK_BPHY_CGX_MSG_TYPE_CPRI_MODE_MISC }
enum	cnxk_bphy_cgx_eth_link_speed {   CNXK_BPHY_CGX_ETH_LINK_SPEED_NONE , CNXK_BPHY_CGX_ETH_LINK_SPEED_10M , CNXK_BPHY_CGX_ETH_LINK_SPEED_100M , CNXK_BPHY_CGX_ETH_LINK_SPEED_1G ,   CNXK_BPHY_CGX_ETH_LINK_SPEED_2HG , CNXK_BPHY_CGX_ETH_LINK_SPEED_5G , CNXK_BPHY_CGX_ETH_LINK_SPEED_10G , CNXK_BPHY_CGX_ETH_LINK_SPEED_20G ,   CNXK_BPHY_CGX_ETH_LINK_SPEED_25G , CNXK_BPHY_CGX_ETH_LINK_SPEED_40G , CNXK_BPHY_CGX_ETH_LINK_SPEED_50G , CNXK_BPHY_CGX_ETH_LINK_SPEED_80G ,   CNXK_BPHY_CGX_ETH_LINK_SPEED_100G , __CNXK_BPHY_CGX_ETH_LINK_SPEED_MAX }
enum	cnxk_bphy_cgx_eth_link_fec { CNXK_BPHY_CGX_ETH_LINK_FEC_NONE , CNXK_BPHY_CGX_ETH_LINK_FEC_BASE_R , CNXK_BPHY_CGX_ETH_LINK_FEC_RS , __CNXK_BPHY_CGX_ETH_LINK_FEC_MAX }
enum	cnxk_bphy_cgx_eth_link_mode {   CNXK_BPHY_CGX_ETH_LINK_MODE_SGMII_BIT , CNXK_BPHY_CGX_ETH_LINK_MODE_1000_BASEX_BIT , CNXK_BPHY_CGX_ETH_LINK_MODE_QSGMII_BIT , CNXK_BPHY_CGX_ETH_LINK_MODE_10G_C2C_BIT ,   CNXK_BPHY_CGX_ETH_LINK_MODE_10G_C2M_BIT , CNXK_BPHY_CGX_ETH_LINK_MODE_10G_KR_BIT , CNXK_BPHY_CGX_ETH_LINK_MODE_20G_C2C_BIT , CNXK_BPHY_CGX_ETH_LINK_MODE_25G_C2C_BIT ,   CNXK_BPHY_CGX_ETH_LINK_MODE_25G_C2M_BIT , CNXK_BPHY_CGX_ETH_LINK_MODE_25G_2_C2C_BIT , CNXK_BPHY_CGX_ETH_LINK_MODE_25G_CR_BIT , CNXK_BPHY_CGX_ETH_LINK_MODE_25G_KR_BIT ,   CNXK_BPHY_CGX_ETH_LINK_MODE_40G_C2C_BIT , CNXK_BPHY_CGX_ETH_LINK_MODE_40G_C2M_BIT , CNXK_BPHY_CGX_ETH_LINK_MODE_40G_CR4_BIT , CNXK_BPHY_CGX_ETH_LINK_MODE_40G_KR4_BIT ,   CNXK_BPHY_CGX_ETH_LINK_MODE_40GAUI_C2C_BIT , CNXK_BPHY_CGX_ETH_LINK_MODE_50G_C2C_BIT , CNXK_BPHY_CGX_ETH_LINK_MODE_50G_C2M_BIT , CNXK_BPHY_CGX_ETH_LINK_MODE_50G_4_C2C_BIT ,   CNXK_BPHY_CGX_ETH_LINK_MODE_50G_CR_BIT , CNXK_BPHY_CGX_ETH_LINK_MODE_50G_KR_BIT , CNXK_BPHY_CGX_ETH_LINK_MODE_80GAUI_C2C_BIT , CNXK_BPHY_CGX_ETH_LINK_MODE_100G_C2C_BIT ,   CNXK_BPHY_CGX_ETH_LINK_MODE_100G_C2M_BIT , CNXK_BPHY_CGX_ETH_LINK_MODE_100G_CR4_BIT , CNXK_BPHY_CGX_ETH_LINK_MODE_100G_KR4_BIT , CNXK_BPHY_CGX_ETH_LINK_MODE_50GAUI_2_C2C_BIT ,   CNXK_BPHY_CGX_ETH_LINK_MODE_50GAUI_2_C2M_BIT , CNXK_BPHY_CGX_ETH_LINK_MODE_50GBASE_CR2_C_BIT , CNXK_BPHY_CGX_ETH_LINK_MODE_50GBASE_KR2_C_BIT , CNXK_BPHY_CGX_ETH_LINK_MODE_100GAUI_2_C2C_BIT ,   CNXK_BPHY_CGX_ETH_LINK_MODE_100GAUI_2_C2M_BIT , CNXK_BPHY_CGX_ETH_LINK_MODE_100GBASE_CR2_BIT , CNXK_BPHY_CGX_ETH_LINK_MODE_100GBASE_KR2_BIT , CNXK_BPHY_CGX_ETH_LINK_MODE_SFI_1G_BIT ,   CNXK_BPHY_CGX_ETH_LINK_MODE_25GBASE_CR_C_BIT , CNXK_BPHY_CGX_ETH_LINK_MODE_25GBASE_KR_C_BIT , __CNXK_BPHY_CGX_ETH_LINK_MODE_MAX }
enum	cnxk_bphy_cgx_eth_mode_cpri {   CNXK_BPHY_CGX_ETH_MODE_CPRI_2_4G_BIT , CNXK_BPHY_CGX_ETH_MODE_CPRI_3_1G_BIT , CNXK_BPHY_CGX_ETH_MODE_CPRI_4_9G_BIT , CNXK_BPHY_CGX_ETH_MODE_CPRI_6_1G_BIT ,   CNXK_BPHY_CGX_ETH_MODE_CPRI_9_8G_BIT , CNXK_BPHY_CGX_ETH_MODE_CPRI_10_1_BIT , CNXK_BPHY_CGX_ETH_MODE_CPRI_24_3G_BIT }
enum	cnxk_bphy_cgx_mode_group { CNXK_BPHY_CGX_MODE_GROUP_ETH , CNXK_BPHY_CGX_MODE_GROUP_CPRI = 2 }
enum	cnxk_bphy_irq_msg_type {   CNXK_BPHY_IRQ_MSG_TYPE_INIT , CNXK_BPHY_IRQ_MSG_TYPE_FINI , CNXK_BPHY_IRQ_MSG_TYPE_REGISTER , CNXK_BPHY_IRQ_MSG_TYPE_UNREGISTER ,   CNXK_BPHY_IRQ_MSG_TYPE_MEM_GET , CNXK_BPHY_MSG_TYPE_NPA_PF_FUNC , CNXK_BPHY_MSG_TYPE_SSO_PF_FUNC }

Functions
static __rte_always_inline int	rte_pmd_bphy_intr_init (uint16_t dev_id)
static __rte_always_inline int	rte_pmd_bphy_intr_fini (uint16_t dev_id)
static __rte_always_inline int	rte_pmd_bphy_intr_register (uint16_t dev_id, int irq_num, cnxk_bphy_intr_handler_t handler, void *data, int cpu)
static __rte_always_inline int	rte_pmd_bphy_intr_unregister (uint16_t dev_id, int irq_num)
static __rte_always_inline int	rte_pmd_bphy_intr_mem_get (uint16_t dev_id, struct cnxk_bphy_mem *mem)
static __rte_always_inline int	rte_pmd_bphy_npa_pf_func_get (uint16_t dev_id, uint16_t *pf_func)
static __rte_always_inline int	rte_pmd_bphy_sso_pf_func_get (uint16_t dev_id, uint16_t *pf_func)
static __rte_always_inline int	rte_pmd_bphy_cgx_get_link_info (uint16_t dev_id, uint16_t lmac, struct cnxk_bphy_cgx_msg_link_info *info)
static __rte_always_inline int	rte_pmd_bphy_cgx_intlbk_disable (uint16_t dev_id, uint16_t lmac)
static __rte_always_inline int	rte_pmd_bphy_cgx_intlbk_enable (uint16_t dev_id, uint16_t lmac)
static __rte_always_inline int	rte_pmd_bphy_cgx_ptp_rx_disable (uint16_t dev_id, uint16_t lmac)
static __rte_always_inline int	rte_pmd_bphy_cgx_ptp_rx_enable (uint16_t dev_id, uint16_t lmac)
static __rte_always_inline int	rte_pmd_bphy_cgx_set_link_mode (uint16_t dev_id, uint16_t lmac, struct cnxk_bphy_cgx_msg_link_mode *mode)
static __rte_always_inline int	rte_pmd_bphy_cgx_set_link_state (uint16_t dev_id, uint16_t lmac, struct cnxk_bphy_cgx_msg_set_link_state *state)
static __rte_always_inline int	rte_pmd_bphy_cgx_start_rxtx (uint16_t dev_id, uint16_t lmac)
static __rte_always_inline int	rte_pmd_bphy_cgx_stop_rxtx (uint16_t dev_id, uint16_t lmac)
static __rte_always_inline int	rte_pmd_bphy_cgx_get_supported_fec (uint16_t dev_id, uint16_t lmac, enum cnxk_bphy_cgx_eth_link_fec *fec)
static __rte_always_inline int	rte_pmd_bphy_cgx_set_fec (uint16_t dev_id, uint16_t lmac, enum cnxk_bphy_cgx_eth_link_fec fec)
static __rte_always_inline int	rte_pmd_bphy_cgx_cpri_mode_change (uint16_t dev_id, uint16_t lmac, struct cnxk_bphy_cgx_msg_cpri_mode_change *mode)
static __rte_always_inline int	rte_pmd_bphy_cgx_cpri_tx_control (uint16_t dev_id, uint16_t lmac, struct cnxk_bphy_cgx_msg_cpri_mode_tx_ctrl *mode)
static __rte_always_inline int	rte_pmd_bphy_cgx_cpri_mode_misc (uint16_t dev_id, uint16_t lmac, struct cnxk_bphy_cgx_msg_cpri_mode_misc *mode)
int	rte_pmd_bphy_npa_pf_func_get_rmt (uint16_t *pf_func)
int	rte_pmd_bphy_sso_pf_func_get_rmt (uint16_t *pf_func)

Detailed Description

Marvell CGX and BPHY PMD specific structures and interface

This API allows applications to manage BPHY memory in user space along with installing interrupt handlers for low latency signal processing.

Definition in file rte_pmd_bphy.h.

Typedef Documentation

cnxk_bphy_intr_handler_t

typedef void(* cnxk_bphy_intr_handler_t) (int irq_num, void *isr_data)

BPHY interrupt handler

Parameters

irq_num	Zero-based interrupt number
isr_data	Cookie passed to interrupt handler

Definition at line 299 of file rte_pmd_bphy.h.

Enumeration Type Documentation

cnxk_bphy_cgx_msg_type

enum cnxk_bphy_cgx_msg_type

Available message types

Enumerator
CNXK_BPHY_CGX_MSG_TYPE_GET_LINKINFO	Type used to obtain link information
CNXK_BPHY_CGX_MSG_TYPE_INTLBK_DISABLE	Type used to disable internal loopback
CNXK_BPHY_CGX_MSG_TYPE_INTLBK_ENABLE	Type used to enable loopback
CNXK_BPHY_CGX_MSG_TYPE_PTP_RX_DISABLE	Type used to disable PTP on RX
CNXK_BPHY_CGX_MSG_TYPE_PTP_RX_ENABLE	Type used to enable PTP on RX
CNXK_BPHY_CGX_MSG_TYPE_SET_LINK_MODE	Type used to set link mode
CNXK_BPHY_CGX_MSG_TYPE_SET_LINK_STATE	Type used to set link state
CNXK_BPHY_CGX_MSG_TYPE_START_RXTX	Type used to start transmission and packet reception
CNXK_BPHY_CGX_MSG_TYPE_STOP_RXTX	Type used to stop transmission and packet reception
CNXK_BPHY_CGX_MSG_TYPE_GET_SUPPORTED_FEC	Type used to obtain supported FEC
CNXK_BPHY_CGX_MSG_TYPE_SET_FEC	Type used to set FEC
CNXK_BPHY_CGX_MSG_TYPE_CPRI_MODE_CHANGE	Type used to switch from eCPRI to CPRI
CNXK_BPHY_CGX_MSG_TYPE_CPRI_TX_CONTROL	Type used to enable TX for CPRI SERDES
CNXK_BPHY_CGX_MSG_TYPE_CPRI_MODE_MISC	Type use to change misc CPRI SERDES settings

Definition at line 36 of file rte_pmd_bphy.h.

cnxk_bphy_cgx_eth_link_speed

enum cnxk_bphy_cgx_eth_link_speed

Available link speeds

Enumerator
CNXK_BPHY_CGX_ETH_LINK_SPEED_NONE	None
CNXK_BPHY_CGX_ETH_LINK_SPEED_10M	10 Mbps
CNXK_BPHY_CGX_ETH_LINK_SPEED_100M	100 Mbps
CNXK_BPHY_CGX_ETH_LINK_SPEED_1G	1 Gbps
CNXK_BPHY_CGX_ETH_LINK_SPEED_2HG	2.5 Gbps
CNXK_BPHY_CGX_ETH_LINK_SPEED_5G	5 Gbps
CNXK_BPHY_CGX_ETH_LINK_SPEED_10G	10 Gbps
CNXK_BPHY_CGX_ETH_LINK_SPEED_20G	20 Gbps
CNXK_BPHY_CGX_ETH_LINK_SPEED_25G	25 Gbps
CNXK_BPHY_CGX_ETH_LINK_SPEED_40G	40 Gbps
CNXK_BPHY_CGX_ETH_LINK_SPEED_50G	50 Gbps
CNXK_BPHY_CGX_ETH_LINK_SPEED_80G	80 Gbps
CNXK_BPHY_CGX_ETH_LINK_SPEED_100G	100 Gbps

Definition at line 68 of file rte_pmd_bphy.h.

cnxk_bphy_cgx_eth_link_fec

enum cnxk_bphy_cgx_eth_link_fec

Available FEC modes

Enumerator
CNXK_BPHY_CGX_ETH_LINK_FEC_NONE	Disable FEC
CNXK_BPHY_CGX_ETH_LINK_FEC_BASE_R	Base FEC (IEEE 802.3 CLause 74)
CNXK_BPHY_CGX_ETH_LINK_FEC_RS	Reed-Solomon FEC

Definition at line 86 of file rte_pmd_bphy.h.

cnxk_bphy_cgx_eth_link_mode

enum cnxk_bphy_cgx_eth_link_mode

Available link modes

Enumerator
CNXK_BPHY_CGX_ETH_LINK_MODE_SGMII_BIT	SGMII
CNXK_BPHY_CGX_ETH_LINK_MODE_1000_BASEX_BIT	1000BASE-X
CNXK_BPHY_CGX_ETH_LINK_MODE_QSGMII_BIT	QSGMII
CNXK_BPHY_CGX_ETH_LINK_MODE_10G_C2C_BIT	10GBASE-C2C
CNXK_BPHY_CGX_ETH_LINK_MODE_10G_C2M_BIT	10GBASE-C2M
CNXK_BPHY_CGX_ETH_LINK_MODE_10G_KR_BIT	10GBASE-KR
CNXK_BPHY_CGX_ETH_LINK_MODE_20G_C2C_BIT	20GBASE-C2C
CNXK_BPHY_CGX_ETH_LINK_MODE_25G_C2C_BIT	25GBASE-C2C
CNXK_BPHY_CGX_ETH_LINK_MODE_25G_C2M_BIT	25GBASE-C2M
CNXK_BPHY_CGX_ETH_LINK_MODE_25G_2_C2C_BIT	25GBASE-2-C2M
CNXK_BPHY_CGX_ETH_LINK_MODE_25G_CR_BIT	25GBASE-CR
CNXK_BPHY_CGX_ETH_LINK_MODE_25G_KR_BIT	25GBASE-KR
CNXK_BPHY_CGX_ETH_LINK_MODE_40G_C2C_BIT	40GBASE-C2C
CNXK_BPHY_CGX_ETH_LINK_MODE_40G_C2M_BIT	40GBASE-C2M
CNXK_BPHY_CGX_ETH_LINK_MODE_40G_CR4_BIT	40GBASE-CR4
CNXK_BPHY_CGX_ETH_LINK_MODE_40G_KR4_BIT	40GBASE-KR4
CNXK_BPHY_CGX_ETH_LINK_MODE_40GAUI_C2C_BIT	40GAUI-C2C
CNXK_BPHY_CGX_ETH_LINK_MODE_50G_C2C_BIT	50GBASE-C2C
CNXK_BPHY_CGX_ETH_LINK_MODE_50G_C2M_BIT	50GBASE-C2M
CNXK_BPHY_CGX_ETH_LINK_MODE_50G_4_C2C_BIT	50GBASE-4-C2C
CNXK_BPHY_CGX_ETH_LINK_MODE_50G_CR_BIT	50GBASE-CR
CNXK_BPHY_CGX_ETH_LINK_MODE_50G_KR_BIT	50GBASE-KR
CNXK_BPHY_CGX_ETH_LINK_MODE_80GAUI_C2C_BIT	80GAUI-C2C
CNXK_BPHY_CGX_ETH_LINK_MODE_100G_C2C_BIT	100GBASE-C2C
CNXK_BPHY_CGX_ETH_LINK_MODE_100G_C2M_BIT	100GBASE-C2M
CNXK_BPHY_CGX_ETH_LINK_MODE_100G_CR4_BIT	100GBASE-CR4
CNXK_BPHY_CGX_ETH_LINK_MODE_100G_KR4_BIT	100GBASE-KR4
CNXK_BPHY_CGX_ETH_LINK_MODE_50GAUI_2_C2C_BIT	50GAUI-2-C2C
CNXK_BPHY_CGX_ETH_LINK_MODE_50GAUI_2_C2M_BIT	50GAUI-2-C2M
CNXK_BPHY_CGX_ETH_LINK_MODE_50GBASE_CR2_C_BIT	50GBASE-CR2-C
CNXK_BPHY_CGX_ETH_LINK_MODE_50GBASE_KR2_C_BIT	50GBASE-KR2-C
CNXK_BPHY_CGX_ETH_LINK_MODE_100GAUI_2_C2C_BIT	100GAUI-2-C2C
CNXK_BPHY_CGX_ETH_LINK_MODE_100GAUI_2_C2M_BIT	100GAUI-2-C2M
CNXK_BPHY_CGX_ETH_LINK_MODE_100GBASE_CR2_BIT	100GBASE-CR2
CNXK_BPHY_CGX_ETH_LINK_MODE_100GBASE_KR2_BIT	100GBASE-KR2
CNXK_BPHY_CGX_ETH_LINK_MODE_SFI_1G_BIT	SFI-1G
CNXK_BPHY_CGX_ETH_LINK_MODE_25GBASE_CR_C_BIT	25GBASE-CR-C
CNXK_BPHY_CGX_ETH_LINK_MODE_25GBASE_KR_C_BIT	25GBASE-KR-C

Definition at line 97 of file rte_pmd_bphy.h.

cnxk_bphy_cgx_eth_mode_cpri

enum cnxk_bphy_cgx_eth_mode_cpri

Available CPRI modes

Enumerator
CNXK_BPHY_CGX_ETH_MODE_CPRI_2_4G_BIT	2.4G Lane Rate
CNXK_BPHY_CGX_ETH_MODE_CPRI_3_1G_BIT	3.1G Lane Rate
CNXK_BPHY_CGX_ETH_MODE_CPRI_4_9G_BIT	4.9G Lane Rate
CNXK_BPHY_CGX_ETH_MODE_CPRI_6_1G_BIT	6.1G Lane Rate
CNXK_BPHY_CGX_ETH_MODE_CPRI_9_8G_BIT	9.8G Lane Rate
CNXK_BPHY_CGX_ETH_MODE_CPRI_10_1_BIT	10.1G Lane Rate
CNXK_BPHY_CGX_ETH_MODE_CPRI_24_3G_BIT	24.3G Lane Rate

Definition at line 178 of file rte_pmd_bphy.h.

cnxk_bphy_cgx_mode_group

enum cnxk_bphy_cgx_mode_group

Available mode groups

Enumerator
CNXK_BPHY_CGX_MODE_GROUP_ETH	ETH group
CNXK_BPHY_CGX_MODE_GROUP_CPRI	CPRI group

Definition at line 196 of file rte_pmd_bphy.h.

cnxk_bphy_irq_msg_type

enum cnxk_bphy_irq_msg_type

Available IRQ configuration commands

Enumerator
CNXK_BPHY_IRQ_MSG_TYPE_INIT	Type used to initialize interrupts
CNXK_BPHY_IRQ_MSG_TYPE_FINI	Type used to deinitialize interrupts
CNXK_BPHY_IRQ_MSG_TYPE_REGISTER	Type used to register interrupt
CNXK_BPHY_IRQ_MSG_TYPE_UNREGISTER	Type used to unregister interrupt
CNXK_BPHY_IRQ_MSG_TYPE_MEM_GET	Type used to retrieve BPHY memory
CNXK_BPHY_MSG_TYPE_NPA_PF_FUNC	Type used to retrieve NPA PF function
CNXK_BPHY_MSG_TYPE_SSO_PF_FUNC	Type used to retrieve NPA SSO function

Definition at line 309 of file rte_pmd_bphy.h.

Function Documentation

rte_pmd_bphy_intr_init()

static __rte_always_inline int rte_pmd_bphy_intr_init ( uint16_t  dev_id )

static

Initialize BPHY subsystem

Parameters

dev_id

The identifier of the device

Returns

Returns 0 on success, negative error code otherwise

Definition at line 392 of file rte_pmd_bphy.h.

rte_pmd_bphy_intr_fini()

static __rte_always_inline int rte_pmd_bphy_intr_fini ( uint16_t  dev_id )

static

Deinitialize BPHY subsystem

Parameters

dev_id

The identifier of the device

Returns

Returns 0 on success, negative error code otherwise

Definition at line 412 of file rte_pmd_bphy.h.

rte_pmd_bphy_intr_register()

static __rte_always_inline int rte_pmd_bphy_intr_register ( uint16_t  dev_id, int  irq_num, cnxk_bphy_intr_handler_t  handler, void *  data, int  cpu  )

static

Register BPHY interrupt handler

Parameters

dev_id	The identifier of the device
irq_num	Zero-based interrupt number
handler	Interrupt handler to be executed
data	Data to be passed to interrupt handler
cpu	CPU number which will be handling interrupt

Returns

Returns 0 on success, negative error code otherwise

Definition at line 440 of file rte_pmd_bphy.h.

rte_pmd_bphy_intr_unregister()

static __rte_always_inline int rte_pmd_bphy_intr_unregister ( uint16_t  dev_id, int  irq_num  )

static

Unregister BPHY interrupt handler

Parameters

dev_id	The identifier of the device
irq_num	Zero-based interrupt number used during registration

Returns

Returns 0 on success, negative error code otherwise

Definition at line 471 of file rte_pmd_bphy.h.

rte_pmd_bphy_intr_mem_get()

static __rte_always_inline int rte_pmd_bphy_intr_mem_get ( uint16_t  dev_id, struct cnxk_bphy_mem *  mem  )

static

Obtain BPHY memory

Parameters

dev_id	The identifier of the device
mem	Memory structure which will be filled for memory access

Returns

Returns 0 on success, negative error code otherwise

Definition at line 497 of file rte_pmd_bphy.h.

rte_pmd_bphy_npa_pf_func_get()

static __rte_always_inline int rte_pmd_bphy_npa_pf_func_get ( uint16_t  dev_id, uint16_t *  pf_func  )

static

Obtain NPA PF func

Parameters

dev_id	The identifier of the device
pf_func	NPA PF function to obtain

Returns

Returns 0 on success, negative error code otherwise

Definition at line 519 of file rte_pmd_bphy.h.

rte_pmd_bphy_sso_pf_func_get()

static __rte_always_inline int rte_pmd_bphy_sso_pf_func_get ( uint16_t  dev_id, uint16_t *  pf_func  )

static

Obtain SSO PF func

Parameters

dev_id	The identifier of the device
pf_func	SSO PF function to obtain

Returns

Returns 0 on success, negative error code otherwise

Definition at line 541 of file rte_pmd_bphy.h.

rte_pmd_bphy_cgx_get_link_info()

static __rte_always_inline int rte_pmd_bphy_cgx_get_link_info ( uint16_t  dev_id, uint16_t  lmac, struct cnxk_bphy_cgx_msg_link_info *  info  )

static

Obtain link information

Parameters

dev_id	The identifier of the device
lmac	LMAC number for operation
info	Link information structure

Returns

Returns 0 on success, negative error code otherwise

Definition at line 565 of file rte_pmd_bphy.h.

rte_pmd_bphy_cgx_intlbk_disable()

static __rte_always_inline int rte_pmd_bphy_cgx_intlbk_disable ( uint16_t  dev_id, uint16_t  lmac  )

static

Disable loopback mode for an interface

Parameters

dev_id	The identifier of the device
lmac	LMAC number for operation

Returns

Returns 0 on success, negative error code otherwise

Definition at line 587 of file rte_pmd_bphy.h.

rte_pmd_bphy_cgx_intlbk_enable()

static __rte_always_inline int rte_pmd_bphy_cgx_intlbk_enable ( uint16_t  dev_id, uint16_t  lmac  )

static

Enable loopback mode for an interface

Parameters

dev_id	The identifier of the device
lmac	LMAC number for operation

Returns

Returns 0 on success, negative error code otherwise

Definition at line 608 of file rte_pmd_bphy.h.

rte_pmd_bphy_cgx_ptp_rx_disable()

static __rte_always_inline int rte_pmd_bphy_cgx_ptp_rx_disable ( uint16_t  dev_id, uint16_t  lmac  )

static

Disable PTP on RX path

Parameters

dev_id	The identifier of the device
lmac	LMAC number for operation

Returns

Returns 0 on success, negative error code otherwise

Definition at line 629 of file rte_pmd_bphy.h.

rte_pmd_bphy_cgx_ptp_rx_enable()

static __rte_always_inline int rte_pmd_bphy_cgx_ptp_rx_enable ( uint16_t  dev_id, uint16_t  lmac  )

static

Enable PTP on RX path

Parameters

dev_id	The identifier of the device
lmac	LMAC number for operation

Returns

Returns 0 on success, negative error code otherwise

Definition at line 650 of file rte_pmd_bphy.h.

rte_pmd_bphy_cgx_set_link_mode()

static __rte_always_inline int rte_pmd_bphy_cgx_set_link_mode ( uint16_t  dev_id, uint16_t  lmac, struct cnxk_bphy_cgx_msg_link_mode *  mode  )

static

Set link mode for a CGX

Parameters

dev_id	The identifier of the device
lmac	LMAC number for operation
mode	Link mode to set

Returns

Returns 0 on success, negative error code otherwise

Definition at line 673 of file rte_pmd_bphy.h.

rte_pmd_bphy_cgx_set_link_state()

static __rte_always_inline int rte_pmd_bphy_cgx_set_link_state ( uint16_t  dev_id, uint16_t  lmac, struct cnxk_bphy_cgx_msg_set_link_state *  state  )

static

Set link state for a CGX

Parameters

dev_id	The identifier of the device
lmac	LMAC number for operation
state	Link state to set

Returns

Returns 0 on success, negative error code otherwise

Definition at line 698 of file rte_pmd_bphy.h.

rte_pmd_bphy_cgx_start_rxtx()

static __rte_always_inline int rte_pmd_bphy_cgx_start_rxtx ( uint16_t  dev_id, uint16_t  lmac  )

static

Start CGX

Parameters

dev_id	The identifier of the device
lmac	LMAC number for operation

Returns

Returns 0 on success, negative error code otherwise

Definition at line 721 of file rte_pmd_bphy.h.

rte_pmd_bphy_cgx_stop_rxtx()

static __rte_always_inline int rte_pmd_bphy_cgx_stop_rxtx ( uint16_t  dev_id, uint16_t  lmac  )

static

Stop CGX

Parameters

dev_id	The identifier of the device
lmac	LMAC number for operation

Returns

Returns 0 on success, negative error code otherwise

Definition at line 742 of file rte_pmd_bphy.h.

rte_pmd_bphy_cgx_get_supported_fec()

static __rte_always_inline int rte_pmd_bphy_cgx_get_supported_fec ( uint16_t  dev_id, uint16_t  lmac, enum cnxk_bphy_cgx_eth_link_fec *  fec  )

static

Get supported list FEC mode

Parameters

dev_id	The identifier of the device
lmac	LMAC number for operation
fec	FEC structure which holds information

Returns

Returns 0 on success, negative error code otherwise

Definition at line 765 of file rte_pmd_bphy.h.

rte_pmd_bphy_cgx_set_fec()

static __rte_always_inline int rte_pmd_bphy_cgx_set_fec ( uint16_t  dev_id, uint16_t  lmac, enum cnxk_bphy_cgx_eth_link_fec  fec  )

static

Set FEC mode for a device

Parameters

dev_id	The identifier of the device
lmac	LMAC number for operation
fec	FEC structure which holds information to set

Returns

Returns 0 on success, negative error code otherwise

Definition at line 789 of file rte_pmd_bphy.h.

rte_pmd_bphy_cgx_cpri_mode_change()

static __rte_always_inline int rte_pmd_bphy_cgx_cpri_mode_change ( uint16_t  dev_id, uint16_t  lmac, struct cnxk_bphy_cgx_msg_cpri_mode_change *  mode  )

static

Switch from eCPRI to CPRI and change

Parameters

dev_id	The identifier of the device
lmac	LMAC number for operation
mode	CPRI structure which holds configuration data

Returns

Returns 0 on success, negative error code otherwise

Definition at line 814 of file rte_pmd_bphy.h.

rte_pmd_bphy_cgx_cpri_tx_control()

static __rte_always_inline int rte_pmd_bphy_cgx_cpri_tx_control ( uint16_t  dev_id, uint16_t  lmac, struct cnxk_bphy_cgx_msg_cpri_mode_tx_ctrl *  mode  )

static

Enable TX for SERDES configured in CPRI mode

Parameters

dev_id	The identifier of the device
lmac	LMAC number for operation
mode	CPRI TX control structure holding control data

Returns

Returns 0 on success, negative error code otherwise

Definition at line 839 of file rte_pmd_bphy.h.

rte_pmd_bphy_cgx_cpri_mode_misc()

static __rte_always_inline int rte_pmd_bphy_cgx_cpri_mode_misc ( uint16_t  dev_id, uint16_t  lmac, struct cnxk_bphy_cgx_msg_cpri_mode_misc *  mode  )

static

CPRI misc settings

Parameters

dev_id	The identifier of the device
lmac	LMAC number for operation
mode	CPRI settings holding misc control data

Returns

Returns 0 on success, negative error code otherwise

Definition at line 864 of file rte_pmd_bphy.h.

rte_pmd_bphy_npa_pf_func_get_rmt()

int rte_pmd_bphy_npa_pf_func_get_rmt

(

uint16_t *

pf_func

)

Obtain NPA PF func

Parameters

pf_func

Address of an NPA PF and function for NPA free pointer requests to obtain

Returns

Returns 0 on success, negative error code otherwise

rte_pmd_bphy_sso_pf_func_get_rmt()

int rte_pmd_bphy_sso_pf_func_get_rmt

(

uint16_t *

pf_func

)

Obtain SSO PF func

Parameters

pf_func

Address SSO PF and function for SSO add-work requests to obtain

Returns

Returns 0 on success, negative error code otherwise