DPDK  21.02.0
Data Fields
rte_comp_op Struct Reference

#include <rte_comp.h>

Data Fields

struct rte_mempoolmempool
 
rte_iova_t iova_addr
 
struct rte_mbufm_src
 
struct rte_mbufm_dst
 
enum rte_comp_flush_flag flush_flag
 
uint64_t input_chksum
 
uint64_t output_chksum
 
uint32_t consumed
 
uint32_t produced
 
uint64_t debug_status
 
uint8_t status
 
void * private_xform
 
void * stream
 
uint32_t offset
 
uint32_t length
 
uint8_t * digest
 

Detailed Description

Compression Operation.

This structure contains data relating to performing a compression operation on the referenced mbuf data buffers.

Comp operations are enqueued and dequeued in comp PMDs using the rte_compressdev_enqueue_burst() / rte_compressdev_dequeue_burst() APIs

Definition at line 287 of file rte_comp.h.

Field Documentation

void* private_xform

Stateless private PMD data derived from an rte_comp_xform. A handle returned by rte_compressdev_private_xform_create() must be attached to operations of op_type RTE_COMP_STATELESS.

Definition at line 290 of file rte_comp.h.

void* stream

Private PMD data derived initially from an rte_comp_xform, which holds state and history data and evolves as operations are processed. rte_compressdev_stream_create() must be called on a device for all STATEFUL data streams and the resulting stream attached to the one or more operations associated with the data stream. All operations in a stream must be sent to the same device.

Definition at line 295 of file rte_comp.h.

struct rte_mempool* mempool

Pool from which operation is allocated

Definition at line 306 of file rte_comp.h.

rte_iova_t iova_addr

IOVA address of this operation

IO address of the buffer

Definition at line 308 of file rte_comp.h.

struct rte_mbuf* m_src

source mbuf The total size of the input buffer(s) can be retrieved using rte_pktmbuf_pkt_len(m_src). The max data size which can fit in a single mbuf is limited by the uint16_t rte_mbuf.data_len to 64k-1. If the input data is bigger than this it can be passed to the PMD in a chain of mbufs if the PMD's capabilities indicate it supports this.

Definition at line 310 of file rte_comp.h.

struct rte_mbuf* m_dst

destination mbuf The total size of the output buffer(s) can be retrieved using rte_pktmbuf_pkt_len(m_dst). The max data size which can fit in a single mbuf is limited by the uint16_t rte_mbuf.data_len to 64k-1. If the output data is expected to be bigger than this a chain of mbufs can be passed to the PMD if the PMD's capabilities indicate it supports this.

Note
, if incompressible data is passed to an engine for compression using RTE_COMP_ALGO_DEFLATE, it's possible for the output data to be larger than the uncompressed data, due to the inclusion of the DEFLATE header blocks. The size of m_dst should accommodate this, else OUT_OF_SPACE errors can be expected in this case.

Definition at line 318 of file rte_comp.h.

uint32_t offset

Starting point for compression or decompression, specified as number of bytes from start of packet in source buffer. This offset starts from the first segment of the buffer, in case the m_src is a chain of mbufs. Starting point for checksum generation in compress direction.

Starting point for writing output data, specified as number of bytes from start of packet in dest buffer. This offset starts from the first segment of the buffer, in case the m_dst is a chain of mbufs. Starting point for checksum generation in decompress direction.

Definition at line 335 of file rte_comp.h.

uint32_t length

The length, in bytes, of the data in source buffer to be compressed or decompressed. Also the length of the data over which the checksum should be generated in compress direction

Definition at line 343 of file rte_comp.h.

uint8_t* digest

Output buffer to store hash output, if enabled in xform. Buffer would contain valid value only after an op with flush flag = RTE_COMP_FLUSH_FULL/FLUSH_FINAL is processed successfully.

Length of buffer should be contiguous and large enough to accommodate digest produced by specific hash algo.

Definition at line 362 of file rte_comp.h.

enum rte_comp_flush_flag flush_flag

Defines flush characteristics for the output data. Only applicable in compress direction

Definition at line 374 of file rte_comp.h.

uint64_t input_chksum

An input checksum can be provided to generate a cumulative checksum across sequential blocks in a STATELESS stream. Checksum type is as specified in xform chksum_type

Definition at line 378 of file rte_comp.h.

uint64_t output_chksum

If a checksum is generated it will be written in here. Checksum type is as specified in xform chksum_type.

Definition at line 383 of file rte_comp.h.

uint32_t consumed

The number of bytes from the source buffer which were compressed/decompressed.

Definition at line 387 of file rte_comp.h.

uint32_t produced

The number of bytes written to the destination buffer which were compressed/decompressed.

Definition at line 391 of file rte_comp.h.

uint64_t debug_status

Status of the operation is returned in the status param. This field allows the PMD to pass back extra pmd-specific debug information. Value is not defined on the API.

Definition at line 395 of file rte_comp.h.

uint8_t status

Operation status - use values from enum rte_comp_status. This is reset to RTE_COMP_OP_STATUS_NOT_PROCESSED on allocation from mempool and will be set to RTE_COMP_OP_STATUS_SUCCESS after operation is successfully processed by a PMD

Definition at line 401 of file rte_comp.h.


The documentation for this struct was generated from the following file: