Testpmd Application User Guide

April 03, 2015

Contents

• 1. Introduction
  • 1.1. DocumentationRoadmap
• 2. Overview
• 3. Compiling the Application
• 4. Running the Application
  • 4.1. EAL Command-line Options
  • 4.2. Testpmd Command-line Options
• 5. Testpmd Runtime Functions
  • 5.1. Help Functions
  • 5.2. Control Functions
    • 5.2.1. start
    • 5.2.2. start tx_first
    • 5.2.3. stop
    • 5.2.4. quit
  • 5.3. Display Functions
    • 5.3.1. show port
    • 5.3.2. show port rss reta
    • 5.3.3. show port rss-hash
    • 5.3.4. clear port
    • 5.3.5. show config
    • 5.3.6. read rxd
    • 5.3.7. read txd
  • 5.4. Configuration Functions
    • 5.4.1. set default
    • 5.4.2. set verbose
    • 5.4.3. set nbport
    • 5.4.4. set nbcore
    • 5.4.5. set coremask
    • 5.4.6. set portmask
    • 5.4.7. set burst
    • 5.4.8. set txpkts
    • 5.4.9. set corelist
    • 5.4.10. set portlist
    • 5.4.11. vlan set strip
    • 5.4.12. vlan set stripq
    • 5.4.13. vlan set filter
    • 5.4.14. vlan set qinq
    • 5.4.15. vlan set tpid
    • 5.4.16. rx_vlan add
    • 5.4.17. rx_vlan rm
    • 5.4.18. rx_vlan add(for VF)
    • 5.4.19. rx_vlan rm(for VF)
    • 5.4.20. rx_vlan set tpid
    • 5.4.21. tunnel_filter add
    • 5.4.22. tunnel_filter remove
    • 5.4.23. rx_vxlan_port add
    • 5.4.24. rx_vxlan_port remove
    • 5.4.25. tx_vlan set
    • 5.4.26. tx_vlan set pvid
    • 5.4.27. tx_vlan reset
    • 5.4.28. csum set
    • 5.4.29. csum parse-tunnel
    • 5.4.30. csum show
    • 5.4.31. tso set
    • 5.4.32. tso show
    • 5.4.33. set fwd
    • 5.4.34. mac_addr add
    • 5.4.35. mac_addr remove
    • 5.4.36. mac_addr add(for VF)
    • 5.4.37. set port-uta
    • 5.4.38. set promisc
    • 5.4.39. set allmulti
    • 5.4.40. set flow_ctrl rx
    • 5.4.41. set pfc_ctrl rx
    • 5.4.42. set stat_qmap
    • 5.4.43. set port - rx/tx(for VF)
    • 5.4.44. set port - mac address filter (for VF)
    • 5.4.45. set port - rx mode(for VF)
    • 5.4.46. set port - tx_rate (for Queue)
    • 5.4.47. set port - tx_rate (for VF)
    • 5.4.48. set port - mirror rule
    • 5.4.49. reset port - mirror rule
    • 5.4.50. set flush_rx
    • 5.4.51. set bypass mode
    • 5.4.52. set bypass event
    • 5.4.53. set bypass timeout
    • 5.4.54. show bypass config
    • 5.4.55. set link up
    • 5.4.56. set link down
  • 5.5. Port Functions
    • 5.5.1. port attach
    • 5.5.2. port detach
    • 5.5.3. port start
    • 5.5.4. port stop
    • 5.5.5. port close
    • 5.5.6. port start/stop queue
    • 5.5.7. port config - speed
    • 5.5.8. port config - queues/descriptors
    • 5.5.9. port config - max-pkt-len
    • 5.5.10. port config - CRC Strip
    • 5.5.11. port config - RX Checksum
    • 5.5.12. port config - VLAN
    • 5.5.13. port config - VLAN filter
    • 5.5.14. port config - VLAN strip
    • 5.5.15. port config - VLAN extend
    • 5.5.16. port config - Drop Packets
    • 5.5.17. port config - RSS
    • 5.5.18. port config - RSS Reta
    • 5.5.19. port config - DCB
    • 5.5.20. port config - Burst
    • 5.5.21. port config - Threshold
  • 5.6. Link Bonding Functions
    • 5.6.1. create bonded device
    • 5.6.2. add bonding slave
    • 5.6.3. remove bonding slave
    • 5.6.4. set bonding mode
    • 5.6.5. set bonding primary
    • 5.6.6. set bonding mac
    • 5.6.7. set bonding xmit_balance_policy
    • 5.6.8. set bonding mon_period
    • 5.6.9. show bonding config
  • 5.7. Register Functions
    • 5.7.1. read reg
    • 5.7.2. read regfield
    • 5.7.3. read regbit
    • 5.7.4. write reg
    • 5.7.5. write regfield
    • 5.7.6. write regbit
  • 5.8. Filter Functions
    • 5.8.1. ethertype_filter
    • 5.8.2. 2tuple_filter
    • 5.8.3. 5tuple_filter
    • 5.8.4. syn_filter
    • 5.8.5. flex_filter
    • 5.8.6. flow_director_filter
    • 5.8.7. flush_flow_director
    • 5.8.8. flow_director_mask
    • 5.8.9. flow_director_flex_mask
    • 5.8.10. flow_director_flex_payload
    • 5.8.11. get_sym_hash_ena_per_port
    • 5.8.12. set_sym_hash_ena_per_port
    • 5.8.13. get_hash_global_config
    • 5.8.14. set_hash_global_config