5. dpdk-test-crypto-perf Application

5.3.1. EAL Options

The following are the EAL command-line options that can be used in conjunction with the dpdk-test-crypto-perf applcation. See the DPDK Getting Started Guides for more information on these options.

• -c <COREMASK>

  Set the hexadecimal bitmask of the cores to run on.

• -w <PCI>

  Add a PCI device in white list.

• --vdev <driver><id>

  Add a virtual device.

5.3.2. Appication Options

The following are the appication command-line options:

• --ptest type

  Set test type, where type is one of the following:

  throughput
  latency
  

• --silent

  Disable options dump.

• --pool-sz <n>

  Set the number of mbufs to be allocated in the mbuf pool.

• --total-ops <n>

  Set the number of total operations performed.

• --burst-sz <n>

  Set the number of packets per burst.

• --buffer-sz <n>

  Set the size of single packet (plaintext or ciphertext in it).

• --segments-nb <n>

  Set the number of segments per packet.

• --devtype <name>

  Set device type, where name is one of the following:

  crypto_null
  crypto_aesni_mb
  crypto_aesni_gcm
  crypto_openssl
  crypto_qat
  crypto_snow3g
  crypto_kasumi
  crypto_zuc
  

• --optype <name>

  Set operation type, where name is one of the following:

  cipher-only
  auth-only
  cipher-then-auth
  auth-then-cipher
  aead
  

• --sessionless

  Enable session-less crypto operations mode.

• --out-of-place

  Enable out-of-place crypto operations mode.

• --verify

  Enable verify that all crypto operations were successful. The verification is done after the performance test.

• --test-file <name>

  Set test vector file path. See the Test Vector File chapter.

• --test-name <name>

  Set specific test name section in the test vector file.

• --cipher-algo <name>

  Set cipher algorithm name, where name is one of the following:

  3des-cbc
  3des-ecb
  3des-ctr
  aes-cbc
  aes-ccm
  aes-ctr
  aes-ecb
  aes-gcm
  aes-f8
  aes-xts
  arc4
  null
  kasumi-f8
  snow3g-uea2
  zuc-eea3
  

• --cipher-op <mode>

  Set cipher operation mode, where mode is one of the following:

  encrypt
  decrypt
  

• --cipher-key-sz <n>

  Set the size of cipher key.

• --cipher-iv-sz <n>

  Set the size of cipher iv.

• --auth-algo <name>

  Set authentication algorithm name, where name is one of the following:

  3des-cbc
  aes-cbc-mac
  aes-ccm
  aes-cmac
  aes-gcm
  aes-gmac
  aes-xcbc-mac
  md5
  md5-hmac
  sha1
  sha1-hmac
  sha2-224
  sha2-224-hmac
  sha2-256
  sha2-256-hmac
  sha2-384
  sha2-384-hmac
  sha2-512
  sha2-512-hmac
  kasumi-f9
  snow3g-uia2
  zuc-eia3
  

• --auth-op <mode>

  Set authentication operation mode, where mode is one of the following:

  verify
  generate
  

• --auth-key-sz <n>

  Set the size of authentication key.

• --auth-digest-sz <n>

  Set the size of authentication digest.

• --auth-aad-sz <n>

  Set the size of authentication aad.

• --csv-friendly

  Enable test result output CSV friendly rather than human friendly.

5.3.3. Test Vector File

The test vector file is a text file contain information about test vectors. The file is made of the sections. The first section doesn’t have header. It contain global information used in each test variant vectors - typicaly information about plaintext, ciphertext, cipher key, aut key, initial vector. All other sections begin header. The sections contain particular information typicaly digest.

Format of the file:

Each line beginig with sign ‘#’ contain comment and it is ignored by parser:

# <comment>

Header line is just name in square bracket:

[<section name>]

Data line contain information tocken then sign ‘=’ and a string of bytes in C byte array format:

<tocken> = <C byte array>

Tockens list:

• plaintext

  Original plaintext to be crypted.

• ciphertext

  Encrypted plaintext string.

• cipher_key

  Key used in cipher operation.

• auth_key

  Key used in auth operation.

• iv

  Initial vector.

• aad

  Additional data.

• digest

  Digest string.