7. Quick Assist Crypto Poll Mode Driver

The QAT PMD provides poll mode crypto driver support for Intel QuickAssist Technology DH895xxC hardware accelerator.

7.1. Features

The QAT PMD has support for:

Cipher algorithms:

  • RTE_CRYPTO_SYM_CIPHER_AES128_CBC
  • RTE_CRYPTO_SYM_CIPHER_AES192_CBC
  • RTE_CRYPTO_SYM_CIPHER_AES256_CBC
  • RTE_CRYPTO_SYM_CIPHER_AES128_CTR
  • RTE_CRYPTO_SYM_CIPHER_AES192_CTR
  • RTE_CRYPTO_SYM_CIPHER_AES256_CTR
  • RTE_CRYPTO_SYM_CIPHER_SNOW3G_UEA2
  • RTE_CRYPTO_CIPHER_AES_GCM

Hash algorithms:

  • RTE_CRYPTO_AUTH_SHA1_HMAC
  • RTE_CRYPTO_AUTH_SHA256_HMAC
  • RTE_CRYPTO_AUTH_SHA512_HMAC
  • RTE_CRYPTO_AUTH_AES_XCBC_MAC
  • RTE_CRYPTO_AUTH_SNOW3G_UIA2

7.2. Limitations

  • Chained mbufs are not supported.
  • Hash only is not supported except Snow3G UIA2.
  • Cipher only is not supported except Snow3G UEA2.
  • Only supports the session-oriented API implementation (session-less APIs are not supported).
  • Not performance tuned.
  • Snow3g(UEA2) supported only if cipher length, cipher offset fields are byte-aligned.
  • Snow3g(UIA2) supported only if hash length, hash offset fields are byte-aligned.
  • No BSD support as BSD QAT kernel driver not available.

7.3. Installation

To use the DPDK QAT PMD an SRIOV-enabled QAT kernel driver is required. The VF devices exposed by this driver will be used by QAT PMD.

If you are running on kernel 4.4 or greater, see instructions for Installation using kernel.org driver below. If you are on a kernel earlier than 4.4, see Installation using 01.org QAT driver.

7.4. Installation using 01.org QAT driver

Download the latest QuickAssist Technology Driver from 01.org Consult the Getting Started Guide at the same URL for further information.

The steps below assume you are:

  • Building on a platform with one DH895xCC device.
  • Using package qatmux.l.2.3.0-34.tgz.
  • On Fedora21 kernel 3.17.4-301.fc21.x86_64.

In the BIOS ensure that SRIOV is enabled and VT-d is disabled.

Uninstall any existing QAT driver, for example by running:

  • ./installer.sh uninstall in the directory where originally installed.
  • or rmmod qat_dh895xcc; rmmod intel_qat.

Build and install the SRIOV-enabled QAT driver:

mkdir /QAT
cd /QAT
# copy qatmux.l.2.3.0-34.tgz to this location
tar zxof qatmux.l.2.3.0-34.tgz

export ICP_WITHOUT_IOMMU=1
./installer.sh install QAT1.6 host

You can use cat /proc/icp_dh895xcc_dev0/version to confirm the driver is correctly installed. You can use lspci -d:443 to confirm the bdf of the 32 VF devices are available per DH895xCC device.

To complete the installation - follow instructions in Binding the available VFs to the DPDK UIO driver.

Note: If using a later kernel and the build fails with an error relating to strict_stroul not being available apply the following patch:

/QAT/QAT1.6/quickassist/utilities/downloader/Target_CoreLibs/uclo/include/linux/uclo_platform.h
+ #if LINUX_VERSION_CODE >= KERNEL_VERSION(3,18,5)
+ #define STR_TO_64(str, base, num, endPtr) {endPtr=NULL; if (kstrtoul((str), (base), (num))) printk("Error strtoull convert %s\n", str); }
+ #else
#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,38)
#define STR_TO_64(str, base, num, endPtr) {endPtr=NULL; if (strict_strtoull((str), (base), (num))) printk("Error strtoull convert %s\n", str); }
#else
#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,25)
#define STR_TO_64(str, base, num, endPtr) {endPtr=NULL; strict_strtoll((str), (base), (num));}
#else
#define STR_TO_64(str, base, num, endPtr)                                 \
     do {                                                               \
           if (str[0] == '-')                                           \
           {                                                            \
                *(num) = -(simple_strtoull((str+1), &(endPtr), (base))); \
           }else {                                                      \
                *(num) = simple_strtoull((str), &(endPtr), (base));      \
           }                                                            \
     } while(0)
+ #endif
#endif
#endif

If the build fails due to missing header files you may need to do following:

  • sudo yum install zlib-devel
  • sudo yum install openssl-devel

If the build or install fails due to mismatching kernel sources you may need to do the following:

  • sudo yum install kernel-headers-`uname -r`
  • sudo yum install kernel-src-`uname -r`
  • sudo yum install kernel-devel-`uname -r`

7.5. Installation using kernel.org driver

Assuming you are running on at least a 4.4 kernel, you can use the stock kernel.org QAT driver to start the QAT hardware.

The steps below assume you are:

  • Running DPDK on a platform with one DH895xCC device.
  • On a kernel at least version 4.4.

In BIOS ensure that SRIOV is enabled and VT-d is disabled.

Ensure the QAT driver is loaded on your system, by executing:

lsmod | grep qat

You should see the following output:

qat_dh895xcc            5626  0
intel_qat              82336  1 qat_dh895xcc

Next, you need to expose the VFs using the sysfs file system.

First find the bdf of the DH895xCC device:

lspci -d : 435

You should see output similar to:

03:00.0 Co-processor: Intel Corporation Coleto Creek PCIe Endpoint

Using the sysfs, enable the VFs:

echo 32 > /sys/bus/pci/drivers/dh895xcc/0000\:03\:00.0/sriov_numvfs

If you get an error, it’s likely you’re using a QAT kernel driver earlier than kernel 4.4.

To verify that the VFs are available for use - use lspci -d:443 to confirm the bdf of the 32 VF devices are available per DH895xCC device.

To complete the installation - follow instructions in Binding the available VFs to the DPDK UIO driver.

Note: If the QAT kernel modules are not loaded and you see an error like
Failed to load MMP firmware qat_895xcc_mmp.bin this may be as a result of not using a distribution, but just updating the kernel directly.

Download firmware from the kernel firmware repo at: http://git.kernel.org/cgit/linux/kernel/git/firmware/linux-firmware.git/tree/

Copy qat binaries to /lib/firmware: * cp qat_895xcc.bin /lib/firmware * cp qat_895xcc_mmp.bin /lib/firmware

cd to your linux source root directory and start the qat kernel modules: * insmod ./drivers/crypto/qat/qat_common/intel_qat.ko * insmod ./drivers/crypto/qat/qat_dh895xcc/qat_dh895xcc.ko

Note:The following warning in /var/log/messages can be ignored:
IOMMU should be enabled for SR-IOV to work correctly

7.6. Binding the available VFs to the DPDK UIO driver

The unbind command below assumes bdfs of 03:01.00-03:04.07, if yours are different adjust the unbind command below:

cd $RTE_SDK
modprobe uio
insmod ./build/kmod/igb_uio.ko

for device in $(seq 1 4); do \
    for fn in $(seq 0 7); do \
        echo -n 0000:03:0${device}.${fn} > \
        /sys/bus/pci/devices/0000\:03\:0${device}.${fn}/driver/unbind; \
    done; \
done

echo "8086 0443" > /sys/bus/pci/drivers/igb_uio/new_id

You can use lspci -vvd:443 to confirm that all devices are now in use by igb_uio kernel driver.