.. SPDX-License-Identifier: BSD-3-Clause Copyright(c) 2022 Intel Corporation ===================================================== vm2vm vhost-user/virtio-pmd with DSA driver test plan ===================================================== This document provides the test plan for testing some basic functions with DSA driver(kernel IDXD driver and DPDK vfio-pci driver) in vm2vm vhost-user/virtio-pmd topology environment. 1. vm2vm mergeable, non-mergebale path test with virtio 1.0 and virtio1.1 and check virtio-pmd tx chain packets in mergeable path. 2. dynamic change queue number. .. note:: 1.For packed virtqueue virtio-net test, need qemu version > 4.2.0 and VM kernel version > 5.1, and packed ring multi-queues not support reconnect in qemu yet. 2.For split virtqueue virtio-net with multi-queues server mode test, better to use qemu version >= 5.2.0, dut to qemu(v4.2.0~v5.1.0) exist split ring multi-queues reconnection issue. 3.When DMA devices are bound to vfio driver, VA mode is the default and recommended. For PA mode, page by page mapping may exceed IOMMU's max capability, better to use 1G guest hugepage. 4.DPDK local patch that about vhost pmd is needed when testing Vhost asynchronous data path with testpmd. In this patch, we enable asynchronous data path for vhostpmd. Asynchronous data path is enabled per tx/rx queue, and users need to specify the DMA device used by the tx/rx queue. Each tx/rx queue only supports to use one DMA device (This is limited by the implementation of vhostpmd), but one DMA device can be shared among multiple tx/rx queues of different vhost PMD ports. Prerequisites ============= Topology -------- Test flow: Virtio-pmd-->Vhost-user-->Testpmd-->Vhost-user-->Virtio-pmd Software -------- iperf General set up -------------- 1. Compile DPDK:: # CC=gcc meson --werror -Denable_kmods=True -Dlibdir=lib -Dexamples=all --default-library=static # ninja -C -j 110 For example: CC=gcc meson --werror -Denable_kmods=True -Dlibdir=lib -Dexamples=all --default-library=static x86_64-native-linuxapp-gcc ninja -C x86_64-native-linuxapp-gcc -j 110 2. Get the PCI device of DUT, for example, 0000:6a:01.0 - 0000:f6:01.0 are DSA devices:: # ./usertools/dpdk-devbind.py -s DMA devices using kernel driver =============================== 0000:6a:01.0 'Device 0b25' drv=idxd unused=vfio-pci 0000:6f:01.0 'Device 0b25' drv=idxd unused=vfio-pci 0000:74:01.0 'Device 0b25' drv=idxd unused=vfio-pci 0000:79:01.0 'Device 0b25' drv=idxd unused=vfio-pci 0000:e7:01.0 'Device 0b25' drv=idxd unused=vfio-pci 0000:ec:01.0 'Device 0b25' drv=idxd unused=vfio-pci 0000:f1:01.0 'Device 0b25' drv=idxd unused=vfio-pci 0000:f6:01.0 'Device 0b25' drv=idxd unused=vfio-pci Test case ========= Common steps ------------ 1.Bind DSA devices to DPDK vfio-pci driver:: # ./usertools/dpdk-devbind.py -b vfio-pci For example, bind 2 DSA devices to vfio-pci driver: # ./usertools/dpdk-devbind.py -b vfio-pci 0000:e7:01.0 0000:ec:01.0 .. note:: One DPDK DSA device can create 8 WQ at most. Below is an example, where DPDK DSA device will create one and eight WQ for DSA deivce 0000:e7:01.0 and 0000:ec:01.0. The value of “max_queues” is 1~8: # ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 4 -n 4 -a 0000:e7:01.0,max_queues=1 -- -i # ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 4 -n 4 -a 0000:ec:01.0,max_queues=8 -- -i 2. Bind DSA devices to kernel idxd driver, and configure Work Queue (WQ):: # ./usertools/dpdk-devbind.py -b idxd # ./drivers/dma/dma/idxd/dpdk_idxd_cfg.py -q .. note:: Better to reset WQ when need operate DSA devices that bound to idxd drvier: # ./drivers/dma/idxd/dpdk_idxd_cfg.py --reset You can check it by 'ls /dev/dsa' dsa_idx: Index of DSA devices, where 0<=dsa_idx<=7, corresponding to 0000:6a:01.0 - 0000:f6:01.0 wq_num: Number of workqueues per DSA endpoint, where 1<=wq_num<=8 For example, bind 2 DSA devices to idxd driver and configure WQ: # ./usertools/dpdk-devbind.py -b idxd 6a:01.0 6f:01.0 # ./drivers/dma/idxd/dpdk_idxd_cfg.py -q 1 0 # ./drivers/dma/idxd/dpdk_idxd_cfg.py -q 4 1 Check WQ by 'ls /dev/dsa' and can find "wq0.0 wq1.0 wq1.1 wq1.2 wq1.3" Test Case 1: VM2VM virtio-pmd split ring mergeable path dynamic queue size with dsa dpdk driver and server mode --------------------------------------------------------------------------------------------------------------- This case tests split ring mergeable path in VM2VM vhost-user/virtio-pmd topology when vhost uses the asynchronous operations with dsa dpdk driver, check that it can tx chain packets normally after dynamically changing queue number from vhost, reconnection has also been tested. 1. Bind 2 DSA device to vfio-pci, then launch the testpmd with 2 vhost ports below commands:: # ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost -a 0000:f1:01.0,max_queues=4 \ --vdev 'net_vhost0,iface=vhost-net0,client=1,queues=8,dmas=[txq0@0000:f1:01.0-q0;txq1@0000:f1:01.0-q0;txq2@0000:f1:01.0-q0;txq3@0000:f1:01.0-q0;rxq0@0000:f1:01.0-q1;rxq1@0000:f1:01.0-q1;rxq2@0000:f1:01.0-q1;rxq3@0000:f1:01.0-q1]' \ --vdev 'net_vhost1,iface=vhost-net1,client=1,queues=8,dmas=[txq0@0000:f1:01.0-q2;txq1@0000:f1:01.0-q2;txq2@0000:f1:01.0-q2;txq3@0000:f1:01.0-q2;rxq0@0000:f1:01.0-q3;rxq1@0000:f1:01.0-q3;rxq2@0000:f1:01.0-q3;rxq3@0000:f1:01.0-q3]' \ -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=4 --txq=4 testpmd>start 2. Launch VM1 and VM2 using qemu:: taskset -c 6-16 /usr/local/qemu-7.1.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 9 -m 4096 \ -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \ -numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu22-04.img \ -chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \ -device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \ -monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \ -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \ -chardev socket,id=char0,path=./vhost-net0,server \ -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \ -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :10 taskset -c 17-27 /usr/local/qemu-7.1.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 9 -m 4096 \ -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \ -numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu22-04-2.img \ -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \ -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \ -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \ -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \ -chardev socket,id=char0,path=./vhost-net1,server \ -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \ -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :12 3. On VM1 and VM2, bind virtio device with vfio-pci driver:: modprobe vfio modprobe vfio-pci echo 1 > /sys/module/vfio/parameters/enable_unsafe_noiommu_mode ./usertools/dpdk-devbind.py --force --bind=vfio-pci 0000:00:05.0 4. Launch testpmd in VM1:: # ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0x3 -n 4 -- -i --tx-offloads=0x00 --enable-hw-vlan-strip --txq=8 --rxq=8 --txd=1024 --rxd=1024 --max-pkt-len=9600 --rx-offloads=0x00002000 testpmd>set fwd mac testpmd>start 5. Launch testpmd in VM2 and send imix pkts, check imix packets can looped between two VMs for 1 mins and 4 queues (queue0 to queue3) have packets rx/tx:: # ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0x3 -n 4 -- -i --tx-offloads=0x00 --enable-hw-vlan-strip --txq=8 --rxq=8 --txd=1024 --rxd=1024 --max-pkt-len=9600 --rx-offloads=0x00002000 testpmd>set fwd mac testpmd>set txpkts 64,256,512,1024,2000,64,256,512,1024,2000 testpmd>start tx_first 32 testpmd>show port stats all 6. Check vhost use the asynchronous data path(funtion like virtio_dev_rx_async_xxx/virtio_dev_tx_async_xxx):: perf top 7. Stop vhost, check that both 4 queues can rx/tx queues:: testpmd>stop 8. On host, dynamic change queue numbers:: testpmd>stop testpmd>port stop all testpmd>port config all rxq 8 testpmd>port config all txq 8 testpmd>port start all testpmd>start 9. Send packets by testpmd in VM2:: testpmd>stop testpmd>start tx_first 32 testpmd>show port stats all 10. Check vhost testpmd RX/TX can work normally, packets can looped between two VMs and both 8 queues can RX/TX traffic. 11. Rerun step 6. Test Case 2: VM2VM virtio-pmd split ring non-mergeable path dynamic queue size with dsa dpdk driver and server mode ------------------------------------------------------------------------------------------------------------------- This case tests split ring non-mergeable path in VM2VM vhost-user/virtio-pmd topology when vhost uses the asynchronous operations with dsa dpdk driver, check that it can work normally after dynamically changing queue number at virtio-pmd side, reconnection has also been tested. 1. Bind 2 DSA device to vfio-pci, then launch the testpmd with 2 vhost ports below commands:: ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost -a 0000:f1:01.0,max_queues=4 -a 0000:f6:01.0,max_queues=4 \ --vdev 'net_vhost0,iface=vhost-net0,client=1,queues=8,dmas=[txq0@0000:f1:01.0-q0;txq1@0000:f1:01.0-q0;txq2@0000:f1:01.0-q1;txq3@0000:f1:01.0-q1;rxq0@0000:f1:01.0-q2;rxq1@0000:f1:01.0-q2;rxq2@0000:f1:01.0-q3;rxq3@0000:f1:01.0-q3]' \ --vdev 'net_vhost1,iface=vhost-net1,client=1,queues=8,dmas=[txq0@0000:f6:01.0-q0;txq1@0000:f6:01.0-q0;txq2@0000:f6:01.0-q1;txq3@0000:f6:01.0-q1;rxq0@0000:f6:01.0-q2;rxq1@0000:f6:01.0-q2;rxq2@0000:f6:01.0-q3;rxq3@0000:f6:01.0-q3]' \ -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8 testpmd>start 2. Launch VM1 and VM2 using qemu:: taskset -c 6-16 /usr/local/qemu-7.1.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 9 -m 4096 \ -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \ -numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu22-04.img \ -chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \ -device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \ -monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \ -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \ -chardev socket,id=char0,path=./vhost-net0,server \ -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \ -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :10 taskset -c 17-27 /usr/local/qemu-7.1.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 9 -m 4096 \ -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \ -numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu22-04-2.img \ -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \ -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \ -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \ -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \ -chardev socket,id=char0,path=./vhost-net1,server \ -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \ -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :12 3. On VM1 and VM2, bind virtio device with vfio-pci driver:: modprobe vfio modprobe vfio-pci echo 1 > /sys/module/vfio/parameters/enable_unsafe_noiom mu_mode ./usertools/dpdk-devbind.py --force --bind=vfio-pci 0000:00:05.0 4. Launch testpmd in VM1:: ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0x3 -n 4 -- -i --tx-offloads=0x00 --enable-hw-vlan-strip --txq=8 --rxq=8 --txd=1024 --rxd=1024 testpmd>set fwd mac testpmd>start 5. Launch testpmd in VM2 and send imix pkts, check imix packets can looped between two VMs for 1 mins and 4 queues (queue0 to queue3) have packets rx/tx:: ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0x3 -n 4 -- -i --tx-offloads=0x00 --enable-hw-vlan-strip --txq=8 --rxq=8 --txd=1024 --rxd=1024 testpmd>set fwd mac testpmd>set txpkts 64,256,512 testpmd>start tx_first 32 testpmd>show port stats all 6. Check vhost use the asynchronous data path(funtion like virtio_dev_rx_async_xxx/virtio_dev_tx_async_xxx):: perf top 7. Stop vhost, check that both 8 queues can rx/tx queues, then start the vhost. testpmd>stop testpmd>start 8. On VM2, dynamic change queue numbers at virtio-pmd side from 8 queues to 4 queues:: testpmd>stop testpmd>port stop all testpmd>port config all rxq 4 testpmd>port config all txq 4 testpmd>port start all testpmd>start 9. Send packets by testpmd in VM2, check Check virtio-pmd RX/TX can work normally and imix packets can looped between two VMs for 1 mins:: testpmd>stop testpmd>start tx_first 32 testpmd>show port stats all 10. Rerun step 6. 11. Stop testpmd in VM2, and check that 4 queues can RX/TX traffic. Test Case 3: VM2VM virtio-pmd packed ring mergeable path dynamic queue size with dsa dpdk driver and server mode ---------------------------------------------------------------------------------------------------------------- This case tests packed ring mergeable path in VM2VM vhost-user/virtio-pmd topology when vhost uses the asynchronous operations with dsa dpdk driver, check that it can tx chain packets normally after dynamically changing queue number. 1. Bind 2 DSA device to vfio-pci, then launch the testpmd with 2 vhost ports below commands:: ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost -a 0000:f1:01.0,max_queues=4 \ --vdev 'net_vhost0,iface=vhost-net0,client=1,queues=8,dmas=[txq0@0000:f1:01.0-q0;txq1@0000:f1:01.0-q1;txq2@0000:f1:01.0-q2;txq3@0000:f1:01.0-q3;rxq0@0000:f1:01.0-q0;rxq1@0000:f1:01.0-q1;rxq2@0000:f1:01.0-q2;rxq3@0000:f1:01.0-q3]' \ --vdev 'net_vhost1,iface=vhost-net1,client=1,queues=8,dmas=[txq0@0000:f1:01.0-q0;txq1@0000:f1:01.0-q1;txq2@0000:f1:01.0-q2;txq3@0000:f1:01.0-q3;rxq0@0000:f1:01.0-q0;rxq1@0000:f1:01.0-q1;rxq2@0000:f1:01.0-q2;rxq3@0000:f1:01.0-q3]' \ -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=4 --txq=4 testpmd>start 2. Launch VM1 and VM2 using qemu:: taskset -c 6-16 /usr/local/qemu-7.1.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 9 -m 4096 \ -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \ -numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu22-04.img \ -chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \ -device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \ -monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \ -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \ -chardev socket,id=char0,path=./vhost-net0,server \ -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \ -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :10 taskset -c 17-27 /usr/local/qemu-7.1.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 9 -m 4096 \ -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \ -numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu22-04-2.img \ -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \ -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \ -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \ -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \ -chardev socket,id=char0,path=./vhost-net1,server \ -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \ -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :12 3. On VM1 and VM2, bind virtio device with vfio-pci driver:: modprobe vfio modprobe vfio-pci echo 1 > /sys/module/vfio/parameters/enable_unsafe_noiommu_mode ./usertools/dpdk-devbind.py --force --bind=vfio-pci 0000:00:05.0 4. Launch testpmd in VM1:: ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0x3 -n 4 -- -i --tx-offloads=0x00 --enable-hw-vlan-strip --txq=8 --rxq=8 --txd=1024 --rxd=1024 --max-pkt-len=9600 --rx-offloads=0x00002000 testpmd>set fwd mac testpmd>start 5. Launch testpmd in VM2 and send imix pkts, check imix packets can looped between two VMs for 1 mins and 4 queues (queue0 to queue3) have packets rx/tx:: ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0x3 -n 4 -- -i --tx-offloads=0x00 --enable-hw-vlan-strip --txq=8 --rxq=8 --txd=1024 --rxd=1024 --max-pkt-len=9600 --rx-offloads=0x00002000 testpmd>set fwd mac testpmd>set txpkts 64,256,512,1024,2000,64,256,512,1024,2000 testpmd>start tx_first 32 testpmd>show port stats all testpmd>stop 6. Quit VM2 and relaunch VM2 with split ring:: taskset -c 17-27 /usr/local/qemu-7.1.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 9 -m 4096 \ -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \ -numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu22-04-2.img \ -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \ -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \ -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \ -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \ -chardev socket,id=char0,path=./vhost-net1,server \ -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \ -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :12 7. Bind virtio device with vfio-pci driver:: modprobe vfio modprobe vfio-pci echo 1 > /sys/module/vfio/parameters/enable_unsafe_noiommu_mode ./usertools/dpdk-devbind.py --force --bind=vfio-pci 0000:00:05.0 8. Launch testpmd in VM2 and send imix pkts from VM2:: # ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0x3 -n 4 -- -i --tx-offloads=0x00 --enable-hw-vlan-strip --txq=8 --rxq=8 --txd=1024 --rxd=1024 --max-pkt-len=9600 --rx-offloads=0x00002000 testpmd>set fwd mac testpmd>set txpkts 64,256,512,1024,2000,64,256,512,1024,2000 testpmd>start tx_first 32 9. On host, Check imix packets can looped between two VMs and 4 queues all have packets rx/tx:: testpmd>show port stats all testpmd>stop testpmd>start 10. Check vhost use the asynchronous data path(funtion like virtio_dev_rx_async_xxx/virtio_dev_tx_async_xxx):: perf top 11. On host, dynamic change queue numbers:: testpmd>stop testpmd>port stop all testpmd>port config all rxq 8 testpmd>port config all txq 8 testpmd>port start all testpmd>start 12. Send packets by testpmd in VM2:: testpmd>stop testpmd>start tx_first 32 testpmd>show port stats all 13. Check vhost testpmd RX/TX can work normally, packets can looped between two VMs and both 8 queues can RX/TX traffic. 14. Rerun step 10. Test Case 4: VM2VM virtio-pmd packed ring non-mergeable path dynamic queue size with dsa dpdk driver and server mode -------------------------------------------------------------------------------------------------------------------- This case tests packed ring non-mergeable path in VM2VM vhost-user/virtio-pmd topology when vhost uses the asynchronous operations with dsa dpdk driver, check that it can work normally after dynamically changing queue number at virtio-pmd side. 1. Bind 2 DSA device to vfio-pci, then launch the testpmd with 2 vhost ports below commands:: ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost -a 0000:f1:01.0,max_queues=4 -a 0000:f6:01.0,max_queues=4 \ --vdev 'net_vhost0,iface=vhost-net0,client=1,queues=8,dmas=[txq0@0000:f1:01.0-q0;txq1@0000:f1:01.0-q1;txq2@0000:f1:01.0-q2;txq3@0000:f1:01.0-q3;rxq0@0000:f1:01.0-q0;rxq1@0000:f1:01.0-q1;rxq2@0000:f1:01.0-q2;rxq3@0000:f1:01.0-q3]' \ --vdev 'net_vhost1,iface=vhost-net1,client=1,queues=8,dmas=[txq0@0000:f1:01.0-q0;txq1@0000:f1:01.0-q1;txq2@0000:f1:01.0-q2;txq3@0000:f1:01.0-q3;rxq0@0000:f1:01.0-q0;rxq1@0000:f1:01.0-q1;rxq2@0000:f1:01.0-q2;rxq3@0000:f1:01.0-q3]' \ -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8 testpmd>start 2. Launch VM1 and VM2 using qemu:: taskset -c 6-16 /usr/local/qemu-7.1.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 9 -m 4096 \ -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \ -numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu22-04.img \ -chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \ -device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \ -monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \ -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \ -chardev socket,id=char0,path=./vhost-net0,server \ -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \ -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :10 taskset -c 17-27 /usr/local/qemu-7.1.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 9 -m 4096 \ -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \ -numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu22-04-2.img \ -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \ -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \ -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \ -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \ -chardev socket,id=char0,path=./vhost-net1,server \ -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \ -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :12 3. On VM1 and VM2, bind virtio device with vfio-pci driver:: modprobe vfio modprobe vfio-pci echo 1 > /sys/module/vfio/parameters/enable_unsafe_noiommu_mode ./usertools/dpdk-devbind.py --force --bind=vfio-pci 0000:00:05.0 4. Launch testpmd in VM1:: ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0x3 -n 4 -- -i --tx-offloads=0x00 --enable-hw-vlan-strip --txq=8 --rxq=8 --txd=1024 --rxd=1024 testpmd>set fwd mac testpmd>start 5. Launch testpmd in VM2 and send imix pkts, check imix packets can looped between two VMs for 1 mins:: ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0x3 -n 4 -- -i --tx-offloads=0x00 --enable-hw-vlan-strip --txq=8 --rxq=8 --txd=1024 --rxd=1024 testpmd>set fwd mac testpmd>set txpkts 64,256,512 testpmd>start tx_first 32 testpmd>show port stats all 6. Check vhost use the asynchronous data path(funtion like virtio_dev_rx_async_xxx/virtio_dev_tx_async_xxx):: perf top 7. On VM2, stop the testpmd, check that both 8 queues have packets rx/tx:: testpmd>stop 8. On VM2, dynamic change queue numbers at virtio-pmd side from 8 queues to 4 queues:: testpmd>stop testpmd>port stop all testpmd>port config all rxq 4 te stpmd>port config all txq 4 testpmd>port start all testpmd>start 9. Send packets by testpmd in VM2, check Check virtio-pmd RX/TX can work normally and imix packets can looped between two VMs for 1 mins:: testpmd>stop testpmd>start tx_first 32 testpmd>show port stats all 10. Rerun step 6. 11. Stop testpmd in VM2, and check that 4 queues can RX/TX traffic. Test Case 5: VM2VM virtio-pmd split ring mergeable path dynamic queue size with dsa kernel driver and server mode ----------------------------------------------------------------------------------------------------------------- This case tests split ring mergeable path in VM2VM vhost-user/virtio-pmd topology when vhost uses the asynchronous operations with dsa kernel driver, check that it can tx chain packets normally after dynamically changing queue number at vhost side, reconnection has also been tested. 1. Bind 2 DSA device to idxd:: ls /dev/dsa #check wq configure, reset if exist ./usertools/dpdk-devbind.py -u 6a:01.0 6f:01.0 ./usertools/dpdk-devbind.py -b idxd 6a:01.0 6f:01.0 ./drivers/raw/ioat/dpdk_idxd_cfg.py -q 8 0 ./drivers/raw/ioat/dpdk_idxd_cfg.py -q 8 1 ls /dev/dsa #check wq configure success 2. Launch the testpmd with 2 vhost ports below commands:: ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost \ --vdev 'net_vhost0,iface=vhost-net0,client=1,queues=8,dmas=[txq0@wq0.0;txq1@wq0.0;txq2@wq0.0;txq3@wq0.0;rxq0@wq0.1;rxq1@wq0.1;rxq2@wq0.1;rxq3@wq0.1]' \ --vdev 'net_vhost1,iface=vhost-net1,client=1,queues=8,dmas=[txq0@wq0.1;txq1@wq0.1;txq2@wq0.1;txq3@wq0.1;rxq0@wq0.0;rxq1@wq0.0;rxq2@wq0.0;rxq3@wq0.0]' \ -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=4 --txq=4 testpmd>start 3. Launch VM1 and VM2 using qemu:: taskset -c 6-16 /usr/local/qemu-7.1.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 9 -m 4096 \ -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \ -numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu22-04.img \ -chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \ -device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \ -monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \ -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \ -chardev socket,id=char0,path=./vhost-net0,server \ -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \ -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :10 taskset -c 17-27 /usr/local/qemu-7.1.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 9 -m 4096 \ -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \ -numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu22-04-2.img \ -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \ -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \ -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \ -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \ -chardev socket,id=char0,path=./vhost-net1,server \ -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \ -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :12 4. On VM1 and VM2, bind virtio device with vfio-pci driver:: modprobe vfio modprobe vfio-pci echo 1 > /sys/module/vfio/parameters/enable_unsafe_noiommu_mode ./usertools/dpdk-devbind.py --force --bind=vfio-pci 0000:00:05.0 5. Launch testpmd in VM1:: ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0x3 -n 4 -- -i --tx-offloads=0x00 --enable-hw-vlan-strip --txq=8 --rxq=8 --txd=1024 --rxd=1024 --max-pkt-len=9600 --rx-offloads=0x00002000 testpmd>set fwd mac testpmd>start 6. Launch testpmd in VM2 and send imix pkts, check imix packets can looped between two VMs for 1 mins and 4 queues (queue0 to queue3) have packets rx/tx:: ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0x3 -n 4 -- -i --tx-offloads=0x00 --enable-hw-vlan-strip --txq=8 --rxq=8 --txd=1024 --rxd=1024 --max-pkt-len=9600 --rx-offloads=0x00002000 testpmd>set fwd mac testpmd>set txpkts 64,256,512,1024,2000,64,256,512,1024,2000 testpmd>start tx_first 32 testpmd>show port stats all 7. Check vhost use the asynchronous data path(funtion like virtio_dev_rx_async_xxx/virtio_dev_tx_async_xxx):: perf top 8. Stop vhost, check that both 4 queues can rx/tx queues. 9. On host, dynamic change queue numbers:: testpmd>stop testpmd>port stop all testpmd>port config all rxq 8 testpmd>port config all txq 8 testpmd>port start all testpmd>start 10. Send packets by testpmd in VM2:: testpmd>stop testpmd>start tx_first 32 testpmd>show port stats all 11. Check vhost testpmd RX/TX can work normally, packets can looped between two VMs and both 8 queues can RX/TX traffic. 12. Rerun step 7. Test Case 6: VM2VM virtio-pmd split ring non-mergeable path dynamic queue size with dsa kernel driver and server mode --------------------------------------------------------------------------------------------------------------------- This case tests split ring non-mergeable path in VM2VM vhost-user/virtio-pmd topology when vhost uses the asynchronous operations with dsa kernel driver, check that it can work normally after dynamically changing queue number at virtio-pmd side, reconnection has also been tested. 1. Bind 2 DSA device to idxd:: ls /dev/dsa #check wq configure, reset if exist ./usertools/dpdk-devbind.py -u 6a:01.0 6f:01.0 ./usertools/dpdk-devbind.py -b idxd 6a:01.0 6f:01.0 ./drivers/raw/ioat/dpdk_idxd_cfg.py -q 8 0 ./drivers/raw/ioat/dpdk_idxd_cfg.py -q 8 1 ls /dev/dsa #check wq configure success 2. Launch the testpmd with 2 vhost ports below commands:: ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost \ --vdev 'net_vhost0,iface=vhost-net0,client=1,queues=8,dmas=[txq0@wq0.0;txq1@wq0.0;txq2@wq0.0;txq3@wq0.0;txq4@wq0.1;txq5@wq0.1;rxq2@wq1.0;rxq3@wq1.0;rxq4@wq1.1;rxq5@wq1.1;rxq6@wq1.1;rxq7@wq1.1]' \ --vdev 'net_vhost1,iface=vhost-net1,client=1,queues=8,dmas=[txq0@wq0.0;txq1@wq0.0;txq2@wq0.0;txq3@wq0.0;txq4@wq0.1;txq5@wq0.1;rxq2@wq1.0;rxq3@wq1.0;rxq4@wq1.1;rxq5@wq1.1;rxq6@wq1.1;rxq7@wq1.1]' \ -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8 testpmd>start 3. Launch VM1 and VM2 using qemu:: taskset -c 6-16 /usr/local/qemu-7.1.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 9 -m 4096 \ -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \ -numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu22-04.img \ -chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \ -device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \ -monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \ -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \ -chardev socket,id=char0,path=./vhost-net0,server \ -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \ -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :10 taskset -c 17-27 /usr/local/qemu-7.1.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 9 -m 4096 \ -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \ -numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu22-04-2.img \ -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \ -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \ -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \ -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \ -chardev socket,id=char0,path=./vhost-net1,server \ -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \ -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :12 4. On VM1 and VM2, bind virtio device with vfio-pci driver:: modprobe vfio modprobe vfio-pci echo 1 > /sys/module/vfio/parameters/enable_unsafe_noiommu_mode ./usertools/dpdk-devbind.py --force --bind=vfio-pci 0000:00:05.0 5. Launch testpmd in VM1:: ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0x3 -n 4 -- -i --tx-offloads=0x00 --enable-hw-vlan-strip --txq=8 --rxq=8 --txd=1024 --rxd=1024 testpmd>set fwd mac testpmd>start 6. Launch testpmd in VM2 and send imix pkts, check imix packets can looped between two VMs for 1 mins and 4 queues (queue0 to queue3) have packets rx/tx:: ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0x3 -n 4 -- -i --tx-offloads=0x00 --enable-hw-vlan-strip --txq=8 --rxq=8 --txd=1024 --rxd=1024 testpmd>set fwd mac testpmd>set txpkts 64,256,512 testpmd>start tx_first 32 testpmd>show port stats all 7. Check vhost use the asynchronous data path(funtion like virtio_dev_rx_async_xxx/virtio_dev_tx_async_xxx):: perf top 8. Stop testpmd in host, and check that 8 queues can RX/TX traffic. 8. On VM, dynamic change queue numbers at virtio-pmd side from 8 queues to 4 queues:: testpmd>stop testpmd>port stop all testpmd>port config all rxq 4 testpmd>port config all txq 4 testpmd>port start all testpmd>start 9. Send packets by testpmd in VM2, check Check virtio-pmd RX/TX can work normally and imix packets can looped between two VMs for 1 mins:: testpmd>stop testpmd>start tx_first 32 testpmd>show port stats all 10. Rerun step 7. 11. Stop testpmd in host, and check that 4 queues can RX/TX traffic. Test Case 7: VM2VM virtio-pmd packed ring mergeable path dynamic queue size with dsa kernel driver and server mode ------------------------------------------------------------------------------------------------------------------ This case tests packed ring mergeable path in VM2VM vhost-user/virtio-pmd topology when vhost uses the asynchronous operations with dsa kernel driver, check that it can tx chain packets normally after dynamically changing queue number. 1. Bind 1 DSA device to idxd:: ls /dev/dsa #check wq configure, reset if exist ./usertools/dpdk-devbind.py -u 6a:01.0 ./usertools/dpdk-devbind.py -b idxd 6a:01.0 ./drivers/raw/ioat/dpdk_idxd_cfg.py -q 4 0 ls /dev/dsa #check wq configure success 2. Launch the testpmd with 2 vhost ports below commands:: ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost \ --vdev 'net_vhost0,iface=vhost-net0,client=1,queues=8,dmas=[txq0@wq0.0;txq1@wq0.1;txq2@wq0.2;txq3@wq0.3;rxq0@wq0.0;rxq1@wq0.1;rxq2@wq0.2;rxq3@wq0.3]' \ --vdev 'net_vhost1,iface=vhost-net1,client=1,queues=8,dmas=[txq0@wq0.0;txq1@wq0.1;txq2@wq0.2;txq3@wq0.3;rxq0@wq0.0;rxq1@wq0.1;rxq2@wq0.2;rxq3@wq0.3]' \ -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=4 --txq=4 testpmd>start 3. Launch VM1 and VM2 using qemu:: taskset -c 6-16 /usr/local/qemu-7.1.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 9 -m 4096 \ -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \ -numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu22-04.img \ -chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \ -device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \ -monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \ -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \ -chardev socket,id=char0,path=./vhost-net0,server \ -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \ -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :10 taskset -c 17-27 /usr/local/qemu-7.1.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 9 -m 4096 \ -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \ -numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu22-04-2.img \ -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \ -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \ -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \ -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \ -chardev socket,id=char0,path=./vhost-net1,server \ -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \ -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :12 4. On VM1 and VM2, bind virtio device with vfio-pci driver:: modprobe vfio modprobe vfio-pci echo 1 > /sys/module/vfio/parameters/enable_unsafe_noiommu_mode ./usertools/dpdk-devbind.py --force --bind=vfio-pci 0000:00:05.0 5. Launch testpmd in VM1:: ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0x3 -n 4 -- -i --tx-offloads=0x00 --enable-hw-vlan-strip --txq=8 --rxq=8 --txd=1024 --rxd=1024 --max-pkt-len=9600 --rx-offloads=0x00002000 testpmd>set fwd mac testpmd>start 6. Launch testpmd in VM2 and send imix pkts, check imix packets can looped between two VMs for 1 mins and 4 queues (queue0 to queue3) have packets rx/tx:: ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0x3 -n 4 -- -i --tx-offloads=0x00 --enable-hw-vlan-strip --txq=8 --rxq=8 --txd=1024 --rxd=1024 --max-pkt-len=9600 --rx-offloads=0x00002000 testpmd>set fwd mac testpmd>set txpkts 64,256,512,1024,2000,64,256,512,1024,2000 testpmd>start tx_first 32 testpmd>show port stats all testpmd>stop 7. Quit VM2 and relaunch VM2 with split ring:: taskset -c 17-27 /usr/local/qemu-7.1.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 9 -m 4096 \ -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \ -numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu22-04-2.img \ -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \ -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \ -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \ -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \ -chardev socket,id=char0,path=./vhost-net1,server \ -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \ -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :12 8. Bind virtio device with vfio-pci driver:: modprobe vfio modprobe vfio-pci echo 1 > /sys/module/vfio/parameters/enable_unsafe_noiommu_mode ./usertools/dpdk-devbind.py --force --bind=vfio-pci 0000:00:05.0 9. Launch testpmd in VM2 and send imix pkts from VM2:: ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0x3 -n 4 -- -i --tx-offloads=0x00 --enable-hw-vlan-strip --txq=8 --rxq=8 --txd=1024 --rxd=1024 testpmd>set fwd mac testpmd>set txpkts 64,256,512 testpmd>start tx_first 32 10. Check vhost use the asynchronous data path(funtion like virtio_dev_rx_async_xxx/virtio_dev_tx_async_xxx):: perf top 11. On host, check imix packets can looped between two VMs and 4 queues all have packets rx/tx:: testpmd>show port stats all testpmd>stop 12. On host, dynamic change queue numbers:: testpmd>stop testpmd>port stop all testpmd>port config all rxq 8 testpmd>port config all txq 8 testpmd>port start all testpmd>start 13. Send packets by testpmd in VM2:: testpmd>stop testpmd>start tx_first 32 testpmd>show port stats all 14. Check vhost testpmd RX/TX can work normally, packets can looped between two VMs and both 8 queues can RX/TX traffic. 15. Rerun step 10. Test Case 8: VM2VM virtio-pmd packed ring non-mergeable path dynamic queue size with dsa kernel driver and server mode ---------------------------------------------------------------------------------------------------------------------- This case tests packed ring non-mergeable path in VM2VM vhost-user/virtio-pmd topology when vhost uses the asynchronous operations with dsa kernel driver, check that it can work normally after dynamically changing queue number at virtio-pmd side. 1. Bind 2 DSA device to idxd:: ls /dev/dsa #check wq configure, reset if exist ./usertools/dpdk-devbind.py -u 6a:01.0 6f:01.0 ./usertools/dpdk-devbind.py -b idxd 6a:01.0 6f:01.0 ./drivers/raw/ioat/dpdk_idxd_cfg.py -q 4 0 ./drivers/raw/ioat/dpdk_idxd_cfg.py -q 4 1 ls /dev/dsa #check wq configure success 1. Launch the testpmd with 2 vhost ports below commands:: ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost \ --vdev 'net_vhost0,iface=vhost-net0,client=1,queues=8,dmas=[txq0@wq0.0;txq1@wq0.0;txq2@wq0.0;txq3@wq0.0;txq4@wq0.1;txq5@wq0.1;rxq2@wq1.0;rxq3@wq1.0;rxq4@wq1.1;rxq5@wq1.1;rxq6@wq1.1;rxq7@wq1.1]' \ --vdev 'net_vhost1,iface=vhost-net1,client=1,queues=8,dmas=[txq0@wq0.2;txq1@wq0.2;txq2@wq0.2;txq3@wq0.2;txq4@wq0.3;txq5@wq0.3;rxq2@wq1.2;rxq3@wq1.2;rxq4@wq1.3;rxq5@wq1.3;rxq6@wq1.3;rxq7@wq1.3]' \ -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8 testpmd>start 2. Launch VM1 and VM2 using qemu:: taskset -c 6-16 /usr/local/qemu-7.1.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 9 -m 4096 \ -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \ -numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu22-04.img \ -chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \ -device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \ -monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \ -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \ -chardev socket,id=char0,path=./vhost-net0,server \ -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \ -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :10 taskset -c 17-27 /usr/local/qemu-7.1.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 9 -m 4096 \ -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \ -numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu22-04-2.img \ -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \ -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \ -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \ -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \ -chardev socket,id=char0,path=./vhost-net1,server \ -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \ -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :12 3. On VM1 and VM2, bind virtio device with vfio-pci driver:: modprobe vfio modprobe vfio-pci echo 1 > /sys/module/vfio/parameters/enable_unsafe_noiommu_mode ./usertools/dpdk-devbind.py --force --bind=vfio-pci 0000:00:05.0 4. Launch testpmd in VM1:: ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0x3 -n 4 -- -i --tx-offloads=0x00 --enable-hw-vlan-strip --txq=8 --rxq=8 --txd=1024 --rxd=1024 testpmd>set fwd mac testpmd>start 5. Launch testpmd in VM2 and send imix pkts, check imix packets can looped between two VMs for 1 mins:: ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0x3 -n 4 -- -i --tx-offloads=0x00 --enable-hw-vlan-strip --txq=8 --rxq=8 --txd=1024 --rxd=1024 testpmd>set fwd mac testpmd>set txpkts 64,256,512 testpmd>start tx_first 32 testpmd>show port stats all 6. Check vhost use the asynchronous data path(funtion like virtio_dev_rx_async_xxx/virtio_dev_tx_async_xxx):: perf top 7. On VM2, stop the testpmd, check that both 8 queues have packets rx/tx:: testpmd>stop 8. On VM2, dynamic change queue numbers at virtio-pmd side from 8 queues to 4 queues:: testpmd>stop testpmd>port stop all testpmd>port config all rxq 4 testpmd>port config all txq 4 testpmd>port start all testpmd>start 9. Send packets by testpmd in VM2, check Check virtio-pmd RX/TX can work normally and imix packets can looped between two VMs for 1 mins:: testpmd>stop testpmd>start tx_first 32 testpmd>show port stats all 10. Rerun step 6. 11. Stop testpmd in VM2, and check that 4 queues can RX/TX traffic. 12. On VM2, dynamic change queue numbers at virtio-pmd side from 4 queues to 8 queues:: testpmd>stop testpmd>port stop all testpmd>port config all rxq 8 testpmd>port config all txq 8 testpmd>port start all testpmd>start 13. Send packets by testpmd in VM2, check Check virtio-pmd RX/TX can work normally and imix packets can looped between two VMs for 1 mins:: testpmd>stop testpmd>start tx_first 32 testpmd>show port stats all 14. Rerun step 6. 15. Stop testpmd in VM2, and check that 8 queues can RX/TX traffic.