.. Copyright (c) <2019>, Intel Corporation
All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions
are met:
- Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
- Redistributions in binary forim must reproduce the above copyright
notice, this list of conditions and the following disclaimer in
the documentation and/or other materials provided with the
distribution.
- Neither the name of Intel Corporation nor the names of its
contributors may be used to endorse or promote products derived
from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
"AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
OF THE POSSIBILITY OF SUCH DAMAGE.
==========================================
perf vm2vm vhost-user/virtio-net test plan
==========================================
Description
===========
This test plan test vhost tx offload (TSO) function by verifing the TSO/cksum in the TCP/IP
stack enabled environment with vm2vm split ring and packed ring vhost-user/virtio-net mergeable
path. For packed virtqueue virtio-net test, need qemu version > 4.2.0 and VM kernel version > v5.1.
Test flow
=========
Virtio-net <-> Vhost <-> Testpmd <-> Vhost <-> Virtio-net
Test Case 1: Perf VM2VM split ring vhost-user/virtio-net test with tcp traffic
==============================================================================
1. Launch the Vhost sample by below commands::
rm -rf vhost-net*
./testpmd -l 2-4 -n 4 --no-pci --file-prefix=vhost --vdev 'net_vhost0,iface=vhost-net0,queues=1' \
--vdev 'net_vhost1,iface=vhost-net1,queues=1' -- -i --nb-cores=2 --txd=1024 --rxd=1024
testpmd>start
2. Launch VM1 and VM2::
taskset -c 13 qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 1 -m 4096 \
-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
-numa node,memdev=mem -mem-prealloc -drive file=/home/osimg/ubuntu16.img \
-chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
-device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
-monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
-chardev socket,id=char0,path=./vhost-net0 \
-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce \
-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,mrg_rxbuf=on,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on -vnc :10
taskset -c 15 qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 1 -m 4096 \
-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
-numa node,memdev=mem -mem-prealloc -drive file=/home/osimg/ubuntu16-2.img \
-chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
-device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
-monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
-chardev socket,id=char0,path=./vhost-net1 \
-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce \
-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,mrg_rxbuf=on,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on -vnc :12
3. On VM1, set virtio device IP and run arp protocal::
ifconfig ens5 1.1.1.2
arp -s 1.1.1.8 52:54:00:00:00:02
4. On VM2, set virtio device IP and run arp protocal::
ifconfig ens5 1.1.1.8
arp -s 1.1.1.2 52:54:00:00:00:01
5. Check the iperf performance between two VMs by below commands::
Under VM1, run: `iperf -s -i 1`
Under VM2, run: `iperf -c 1.1.1.2 -i 1 -t 60`
6. Check iperf throughput can get expected data.
Test Case 2: Perf VM2VM split ring vhost-user/virtio-net dequeue zero-copy test with tcp traffic
================================================================================================
1. Launch the Vhost sample by below commands::
rm -rf vhost-net*
./testpmd -l 2-4 -n 4 --no-pci --file-prefix=vhost --vdev 'net_vhost0,iface=vhost-net0,queues=1,dequeue-zero-copy=1' \
--vdev 'net_vhost1,iface=vhost-net1,queues=1,dequeue-zero-copy=1' -- -i --nb-cores=2 --txd=1024 --rxd=1024
testpmd>start
2. Launch VM1 and VM2::
taskset -c 13 qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 1 -m 4096 \
-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
-numa node,memdev=mem -mem-prealloc -drive file=/home/osimg/ubuntu16.img \
-chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
-device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
-monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
-chardev socket,id=char0,path=./vhost-net0 \
-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce \
-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,mrg_rxbuf=on,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on -vnc :10
taskset -c 15 qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 1 -m 4096 \
-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
-numa node,memdev=mem -mem-prealloc -drive file=/home/osimg/ubuntu16-2.img \
-chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
-device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
-monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
-chardev socket,id=char0,path=./vhost-net1 \
-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce \
-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,mrg_rxbuf=on,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on -vnc :12
3. On VM1, set virtio device IP and run arp protocal::
ifconfig ens5 1.1.1.2
arp -s 1.1.1.8 52:54:00:00:00:02
4. On VM2, set virtio device IP and run arp protocal::
ifconfig ens5 1.1.1.8
arp -s 1.1.1.2 52:54:00:00:00:01
5. Check the iperf performance between two VMs by below commands::
Under VM1, run: `iperf -s -i 1`
Under VM2, run: `iperf -c 1.1.1.2 -i 1 -t 60`
6. Check iperf throughput can get expected data.
Test Case 3: Perf VM2VM packed ring vhost-user/virtio-net test with tcp traffic
===============================================================================
1. Launch the Vhost sample by below commands::
rm -rf vhost-net*
./testpmd -l 2-4 -n 4 --no-pci --file-prefix=vhost --vdev 'net_vhost0,iface=vhost-net0,queues=1' \
--vdev 'net_vhost1,iface=vhost-net1,queues=1' -- -i --nb-cores=2 --txd=1024 --rxd=1024
testpmd>start
2. Launch VM1 and VM2::
taskset -c 13 qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 1 -m 4096 \
-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
-numa node,memdev=mem -mem-prealloc -drive file=/home/osimg/ubuntu16.img \
-chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
-device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
-monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
-chardev socket,id=char0,path=./vhost-net0 \
-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce \
-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,mrg_rxbuf=on,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,packed=on -vnc :10
taskset -c 15 qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 1 -m 4096 \
-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
-numa node,memdev=mem -mem-prealloc -drive file=/home/osimg/ubuntu16-2.img \
-chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
-device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
-monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
-chardev socket,id=char0,path=./vhost-net1 \
-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce \
-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,mrg_rxbuf=on,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,packed=on -vnc :12
3. On VM1, set virtio device IP and run arp protocal::
ifconfig ens3 1.1.1.2
arp -s 1.1.1.8 52:54:00:00:00:02
4. On VM2, set virtio device IP and run arp protocal::
ifconfig ens3 1.1.1.8
arp -s 1.1.1.2 52:54:00:00:00:01
5. Check the iperf performance between two VMs by below commands::
Under VM1, run: `iperf -s -i 1`
Under VM2, run: `iperf -c 1.1.1.2 -i 1 -t 60`
6. Check iperf throughput can get expected data.
Test Case 4: Perf VM2VM packed ring vhost-user/virtio-net dequeue zero-copy test with tcp traffic
=================================================================================================
1. Launch the Vhost sample by below commands::
rm -rf vhost-net*
./testpmd -l 2-4 -n 4 --no-pci --file-prefix=vhost --vdev 'net_vhost0,iface=vhost-net0,queues=1,dequeue-zero-copy=1' \
--vdev 'net_vhost1,iface=vhost-net1,queues=1,dequeue-zero-copy=1' -- -i --nb-cores=2 --txd=1024 --rxd=1024
testpmd>start
2. Launch VM1 and VM2::
taskset -c 13 qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 1 -m 4096 \
-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
-numa node,memdev=mem -mem-prealloc -drive file=/home/osimg/ubuntu16.img \
-chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
-device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
-monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
-chardev socket,id=char0,path=./vhost-net0 \
-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce \
-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,mrg_rxbuf=on,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,packed=on -vnc :10
taskset -c 15 qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 1 -m 4096 \
-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
-numa node,memdev=mem -mem-prealloc -drive file=/home/osimg/ubuntu16-2.img \
-chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
-device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
-monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
-chardev socket,id=char0,path=./vhost-net1 \
-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce \
-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,mrg_rxbuf=on,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,packed=on -vnc :12
3. On VM1, set virtio device IP and run arp protocal::
ifconfig ens3 1.1.1.2
arp -s 1.1.1.8 52:54:00:00:00:02
4. On VM2, set virtio device IP and run arp protocal::
ifconfig ens3 1.1.1.8
arp -s 1.1.1.2 52:54:00:00:00:01
5. Check the iperf performance between two VMs by below commands::
Under VM1, run: `iperf -s -i 1`
Under VM2, run: `iperf -c 1.1.1.2 -i 1 -t 60`
6. Check iperf throughput can get expected data.