rte_ring_c11_pvt.h

/* SPDX-License-Identifier: BSD-3-Clause
 *
 * Copyright (c) 2017,2018 HXT-semitech Corporation.
 * Copyright (c) 2007-2009 Kip Macy kmacy@freebsd.org
 * Copyright (c) 2021 Arm Limited
 * All rights reserved.
 * Derived from FreeBSD's bufring.h
 * Used as BSD-3 Licensed with permission from Kip Macy.
 */
 
#ifndef _RTE_RING_C11_PVT_H_
#define _RTE_RING_C11_PVT_H_
 
static __rte_always_inline void
__rte_ring_update_tail(struct rte_ring_headtail *ht, uint32_t old_val,
        uint32_t new_val, uint32_t single, uint32_t enqueue)
{
    RTE_SET_USED(enqueue);
 
    /*
     * If there are other enqueues/dequeues in progress that preceded us,
     * we need to wait for them to complete
     */
    if (!single)
        rte_wait_until_equal_32(&ht->tail, old_val, __ATOMIC_RELAXED);
 
    __atomic_store_n(&ht->tail, new_val, __ATOMIC_RELEASE);
}
 
static __rte_always_inline unsigned int
__rte_ring_move_prod_head(struct rte_ring *r, unsigned int is_sp,
        unsigned int n, enum rte_ring_queue_behavior behavior,
        uint32_t *old_head, uint32_t *new_head,
        uint32_t *free_entries)
{
    const uint32_t capacity = r->capacity;
    uint32_t cons_tail;
    unsigned int max = n;
    int success;
 
    *old_head = __atomic_load_n(&r->prod.head, __ATOMIC_RELAXED);
    do {
        /* Reset n to the initial burst count */
        n = max;
 
        /* Ensure the head is read before tail */
        __atomic_thread_fence(__ATOMIC_ACQUIRE);
 
        /* load-acquire synchronize with store-release of ht->tail
         * in update_tail.
         */
        cons_tail = __atomic_load_n(&r->cons.tail,
                    __ATOMIC_ACQUIRE);
 
        /* The subtraction is done between two unsigned 32bits value
         * (the result is always modulo 32 bits even if we have
         * *old_head > cons_tail). So 'free_entries' is always between 0
         * and capacity (which is < size).
         */
        *free_entries = (capacity + cons_tail - *old_head);
 
        /* check that we have enough room in ring */
        if (unlikely(n > *free_entries))
            n = (behavior == RTE_RING_QUEUE_FIXED) ?
                    0 : *free_entries;
 
        if (n == 0)
            return 0;
 
        *new_head = *old_head + n;
        if (is_sp)
            r->prod.head = *new_head, success = 1;
        else
            /* on failure, *old_head is updated */
            success = __atomic_compare_exchange_n(&r->prod.head,
                    old_head, *new_head,
                    0, __ATOMIC_RELAXED,
                    __ATOMIC_RELAXED);
    } while (unlikely(success == 0));
    return n;
}
 
static __rte_always_inline unsigned int
__rte_ring_move_cons_head(struct rte_ring *r, int is_sc,
        unsigned int n, enum rte_ring_queue_behavior behavior,
        uint32_t *old_head, uint32_t *new_head,
        uint32_t *entries)
{
    unsigned int max = n;
    uint32_t prod_tail;
    int success;
 
    /* move cons.head atomically */
    *old_head = __atomic_load_n(&r->cons.head, __ATOMIC_RELAXED);
    do {
        /* Restore n as it may change every loop */
        n = max;
 
        /* Ensure the head is read before tail */
        __atomic_thread_fence(__ATOMIC_ACQUIRE);
 
        /* this load-acquire synchronize with store-release of ht->tail
         * in update_tail.
         */
        prod_tail = __atomic_load_n(&r->prod.tail,
                    __ATOMIC_ACQUIRE);
 
        /* The subtraction is done between two unsigned 32bits value
         * (the result is always modulo 32 bits even if we have
         * cons_head > prod_tail). So 'entries' is always between 0
         * and size(ring)-1.
         */
        *entries = (prod_tail - *old_head);
 
        /* Set the actual entries for dequeue */
        if (n > *entries)
            n = (behavior == RTE_RING_QUEUE_FIXED) ? 0 : *entries;
 
        if (unlikely(n == 0))
            return 0;
 
        *new_head = *old_head + n;
        if (is_sc)
            r->cons.head = *new_head, success = 1;
        else
            /* on failure, *old_head will be updated */
            success = __atomic_compare_exchange_n(&r->cons.head,
                            old_head, *new_head,
                            0, __ATOMIC_RELAXED,
                            __ATOMIC_RELAXED);
    } while (unlikely(success == 0));
    return n;
}
 
#endif /* _RTE_RING_C11_PVT_H_ */