10. NXP DPAA2 CAAM (DPAA2_SEC)
The DPAA2_SEC PMD provides poll mode crypto driver support for NXP DPAA2 CAAM hardware accelerator.
SEC is the SOC’s security engine, which serves as NXP’s latest cryptographic acceleration and offloading hardware. It combines functions previously implemented in separate modules to create a modular and scalable acceleration and assurance engine. It also implements block encryption algorithms, stream cipher algorithms, hashing algorithms, public key algorithms, run-time integrity checking, and a hardware random number generator. SEC performs higher-level cryptographic operations than previous NXP cryptographic accelerators. This provides significant improvement to system level performance.
DPAA2_SEC is one of the hardware resource in DPAA2 Architecture. More information on DPAA2 Architecture is described in DPAA2 Overview.
DPAA2_SEC PMD is one of DPAA2 drivers which interacts with Management Complex (MC) portal to access the hardware object - DPSECI. The MC provides access to create, discover, connect, configure and destroy dpseci objects in DPAA2_SEC PMD.
DPAA2_SEC PMD also uses some of the other hardware resources like buffer pools, queues, queue portals to store and to enqueue/dequeue data to the hardware SEC.
DPSECI objects are detected by PMD using a resource container called DPRC (like in DPAA2 Overview).
DPRC.1 (bus) | +--+--------+-------+-------+-------+---------+ | | | | | | DPMCP.1 DPIO.1 DPBP.1 DPNI.1 DPMAC.1 DPSECI.1 DPMCP.2 DPIO.2 DPNI.2 DPMAC.2 DPSECI.2 DPMCP.3
SEC provides platform assurance by working with SecMon, which is a companion logic block that tracks the security state of the SOC. SEC is programmed by means of descriptors (not to be confused with frame descriptors (FDs)) that indicate the operations to be performed and link to the message and associated data. SEC incorporates two DMA engines to fetch the descriptors, read the message data, and write the results of the operations. The DMA engine provides a scatter/gather capability so that SEC can read and write data scattered in memory. SEC may be configured by means of software for dynamic changes in byte ordering. The default configuration for this version of SEC is little-endian mode.
A block diagram similar to dpaa2 NIC is shown below to show where DPAA2_SEC fits in the DPAA2 Bus model
+----------------+ | DPDK DPAA2_SEC | | PMD | +----------------+ +------------+ | MC SEC object |.......| Mempool | . . . . . . . . . | (DPSECI) | | (DPBP) | . +---+---+--------+ +-----+------+ . ^ | . . | |<enqueue, . . | | dequeue> . . | | . . +---+---V----+ . . . . . . . . . . . .| DPIO driver| . . . | (DPIO) | . . . +-----+------+ . . . | QBMAN | . . . | Driver | . +----+------+-------+ +-----+----- | . | dpaa2 bus | | . | VFIO fslmc-bus |....................|......................... | | | | /bus/fslmc | | +-------------------+ | | ========================== HARDWARE =====|======================= DPIO | DPSECI---DPBP =========================================|========================
The DPAA2_SEC PMD has support for:
10.4. Supported DPAA2 SoCs
10.5. Allowing & Blocking
The DPAA2 SEC device can be blocked with the following:
<dpdk app> <EAL args> -b "fslmc:dpseci.x" -- ...
Where x is the device object id as configured in resource container.
- Hash followed by Cipher mode is not supported
- Only supports the session-oriented API implementation (session-less APIs are not supported).
DPAA2_SEC driver has similar pre-requisites as described in DPAA2 Overview. The following dependencies are not part of DPDK and must be installed separately:
See NXP QorIQ DPAA2 Board Support Package for setup information
- Follow the DPDK Getting Started Guide for Linux to setup the basic DPDK environment.
10.8. Enabling logs
For enabling logs, use the following EAL parameter:
./your_crypto_application <EAL args> --log-level=pmd.crypto.dpaa2:<level>
crypto.dpaa2 as log matching criteria, all Crypto PMD logs can be
enabled which are lower than logging
10.9. Enabling debug prints
Use dev arg option
drv_dump_mode=x to dump useful debug prints on HW sec
error. There are 3 dump modes available 0, 1 and 2. Mode 0 means no dump print
on error, mode 1 means dump HW error code and mode 2 means dump HW error code
along with other useful debugging information like session, queue, descriptor
10.10. Enable strict ordering
Use dev arg option
drv_strict_order=1 to enable strict ordering.
By default, loose ordering is set for ordered schedule type event.