46. Power Management
The DPDK Power Management feature allows users space applications to save power by dynamically adjusting CPU frequency or entering into different C-States.
- Adjusting the CPU frequency dynamically according to the utilization of RX queue.
- Entering into different deeper C-States according to the adaptive algorithms to speculate brief periods of time suspending the application if no packets are received.
The interfaces for adjusting the operating CPU frequency are in the power management library. C-State control is implemented in applications according to the different use cases.
46.1. CPU Frequency Scaling
The Linux kernel provides a cpufreq module for CPU frequency scaling for each lcore. For example, for cpuX, /sys/devices/system/cpu/cpuX/cpufreq/ has the following sys files for frequency scaling:
In the DPDK, scaling_governor is configured in user space. Then, a user space application can prompt the kernel by writing scaling_setspeed to adjust the CPU frequency according to the strategies defined by the user space application.
46.2. Core-load Throttling through C-States
Core state can be altered by speculative sleeps whenever the specified lcore has nothing to do. In the DPDK, if no packet is received after polling, speculative sleeps can be triggered according the strategies defined by the user space application.
46.3. Per-core Turbo Boost
Individual cores can be allowed to enter a Turbo Boost state on a per-core basis. This is achieved by enabling Turbo Boost Technology in the BIOS, then looping through the relevant cores and enabling/disabling Turbo Boost on each core.
46.4. Use of Power Library in a Hyper-Threaded Environment
In the case where the power library is in use on a system with Hyper-Threading enabled, the frequency on the physical core is set to the highest frequency of the Hyper-Thread siblings. So even though an application may request a scale down, the core frequency will remain at the highest frequency until all Hyper-Threads on that core request a scale down.
46.5. API Overview of the Power Library
The main methods exported by power library are for CPU frequency scaling and include the following:
- Freq up: Prompt the kernel to scale up the frequency of the specific lcore.
- Freq down: Prompt the kernel to scale down the frequency of the specific lcore.
- Freq max: Prompt the kernel to scale up the frequency of the specific lcore to the maximum.
- Freq min: Prompt the kernel to scale down the frequency of the specific lcore to the minimum.
- Get available freqs: Read the available frequencies of the specific lcore from the sys file.
- Freq get: Get the current frequency of the specific lcore.
- Freq set: Prompt the kernel to set the frequency for the specific lcore.
- Enable turbo: Prompt the kernel to enable Turbo Boost for the specific lcore.
- Disable turbo: Prompt the kernel to disable Turbo Boost for the specific lcore.
46.6. User Cases
The power management mechanism is used to save power when performing L3 forwarding.
46.7. Empty Poll API
For packet processing workloads such as DPDK polling is continuous. This means CPU cores always show 100% busy independent of how much work those cores are doing. It is critical to accurately determine how busy a core is hugely important for the following reasons:
- No indication of overload conditions
- User does not know how much real load is on a system, resulting in wasted energy as no power management is utilized
Compared to the original l3fwd-power design, instead of going to sleep after detecting an empty poll, the new mechanism just lowers the core frequency. As a result, the application does not stop polling the device, which leads to improved handling of bursts of traffic.
When the system become busy, the empty poll mechanism can also increase the core frequency (including turbo) to do best effort for intensive traffic. This gives us more flexible and balanced traffic awareness over the standard l3fwd-power application.
46.7.2. Proposed Solution
The proposed solution focuses on how many times empty polls are executed. The less the number of empty polls, means current core is busy with processing workload, therefore, the higher frequency is needed. The high empty poll number indicates the current core not doing any real work therefore, we can lower the frequency to safe power.
In the current implementation, each core has 1 empty-poll counter which assume 1 core is dedicated to 1 queue. This will need to be expanded in the future to support multiple queues per core.
126.96.36.199. Power state definition:
- LOW: Not currently used, reserved for future use.
- MED: the frequency is used to process modest traffic workload.
- HIGH: the frequency is used to process busy traffic workload.
188.8.131.52. There are two phases to establish the power management system:
- Training phase. This phase is used to measure the optimal frequency change thresholds for a given system. The thresholds will differ from system to system due to differences in processor micro-architecture, cache and device configurations. In this phase, the user must ensure that no traffic can enter the system so that counts can be measured for empty polls at low, medium and high frequencies. Each frequency is measured for two seconds. Once the training phase is complete, the threshold numbers are displayed, and normal mode resumes, and traffic can be allowed into the system. These threshold number can be used on the command line when starting the application in normal mode to avoid re-training every time.
- Normal phase. Every 10ms the run-time counters are compared to the supplied threshold values, and the decision will be made whether to move to a different power state (by adjusting the frequency).
46.7.3. API Overview for Empty Poll Power Management
- State Init: initialize the power management system.
- State Free: free the resource hold by power management system.
- Update Empty Poll Counter: update the empty poll counter.
- Update Valid Poll Counter: update the valid poll counter.
- Set the Frequency Index: update the power state/frequency mapping.
- Detect empty poll state change: empty poll state change detection algorithm then take action.
46.8. User Cases
The mechanism can applied to any device which is based on polling. e.g. NIC, FPGA.
46.9. Ethernet PMD Power Management API
Existing power management mechanisms require developers to change application design or change code to make use of it. The PMD power management API provides a convenient alternative by utilizing Ethernet PMD RX callbacks, and triggering power saving whenever empty poll count reaches a certain number.
- This power saving scheme will put the CPU into optimized power state
and use the
rte_power_monitor()function to monitor the Ethernet PMD RX descriptor address, and wake the CPU up whenever there’s new traffic.
- This power saving scheme will avoid busy polling
by either entering power-optimized sleep state
rte_power_pause()function, or, if it’s not available, use
- Frequency scaling
- This power saving scheme will use
librte_powerlibrary functionality to scale the core frequency up/down depending on traffic volume.
Currently, this power management API is limited to mandatory mapping of 1 queue to 1 core (multiple queues are supported, but they must be polled from different cores).
46.9.2. API Overview for Ethernet PMD Power Management
- Queue Enable: Enable specific power scheme for certain queue/port/core.
- Queue Disable: Disable power scheme for certain queue/port/core.
- The L3 Forwarding with Power Management Sample Application chapter in the Sample Applications User Guides section.
- The Virtual Machine Power Management Application chapter in the Sample Applications User Guides section.